Відео

4y55tttttttt

There's a spray can product at the big orange box store that you spray on the coils (let it sit on about 10 min.) and hose off, in case you don't want to use the on-hose cleaner. I did mine without even taking the case off...much better!

Looking to buy the yellow adapter . Did you pushed it with something??? What you called it please. Any link ?

I have to ask why you cut the damn coil out to replace a compressor??? I have done many of those a never had to cut the coil out. Invest in the NAVAC for swage tool. Worth every penny.

I stoled your music and I'm moving to Nashville!

WOW!

Never seen one that dirty.

What kind of sprayer are you using?

1000 dollars for capacitor and coil cleaning, Say its not so?

Wow... Now that it's clean...customer should have a lower light bill..now that compressor isn't working so hard...awesome job

Probably should start showing you turn off the power lol.

Heard the song and knew he knew what he was doing😂😂😂

Careful with that nu-brite on that grass, they’re gonna be pissed when it’s all dead

Yes sir that'll be 500 buckaroos cuz gonna be cold cold now

Spine fin coils are water only. Nu-brite is way too strong.

👍🤙🤘😮

Glad you didn't step off the ledge, looks bit DANGEROUS

Good old carrier heat exchangers, they keep us busy

And they hate hard low volt wires, they want it to be shielded stranded wire

Worked for a carrier dealer and installed many communicating Infiniti systems, the tech is cool but carrier is just all around bad design, many inverter issues, worst heat exchanger design ever, ecm inducers, many installation errors……we are a Rheem dealer now, phenomenal service records……it all starts at the install

What, i thought you couldn't stop a Trane

That’s called the we’re friends discount

is it really worth all the time and effort taking all the metal and coil out just to swap the compressor?

How old is the unit? I’m assuming it’s the variable speed unit?

How old is the unit? I’m assuming it’s the variable speed unit?

That will be $250 sir.

Is the outside condenser unit the same for a heat pump vs a regular AC system? I know the inside “furnace” unit is different.

Lol atleast you where ready! Haha i try to look at the label first to see if its a long shank. Atleast with the equipment i work on, tp valve on the side will be longer to get past insulation, if its op the top, it tends to be short and on a nipple

Mines just went at my house 7yrs after I installed it, sent me a new one 2-3days later from the 15yr warranty.

Too much work. I just remove compressor and braze it back in. No need to remove coil unless you cant reach down there

Man, an hvac guy used one of those crimp connectors on my filter/dryer and it failed massively about 4 mos later. Now my compressor is dead and he says it’s because the reversing valve musta got stuck in the middle. Is he BS’ing me?

As long as the clearance above the ac unit is 5’ or more, the airflow will not be increased in air pressure. That should last along time. IMHO

What refrigerant are you putting in the Bosch? Doesn't look like 410A bottle you got there. Has Bosch already started shipping them out with R32?

Danfoss compressor to the field 😊

Why? That's an old r22 Trane!?!

Ya took the coil off to replace the compressor😅 then used a B tank…….typical Trane bs 😂 I would of had the compressor out and in in 15 minutes

Dude what size are those damn compressor bolts

Why do people keep calling brazing solder ?! It's not soldering 🚫. More heat , makes the difference. Less heat is soldering 😉

that american standard logo is so friggin old. are you that poor of a professional to not basically force someone into something more efficient and that cost less than the repair itself? or is th is work in a 3rd world country?

Lucky if you get 10 -12 years from a pin boiler

👍👍

Dam don’t think I’ve seen that before

Looks like you have done this a time or two , why does the unit sit so high off the ground? ✌️

👍👍

It’s a shit design heat exchanger it holds way to much water as you can see it’s just gonna do it again, if you could clean the water while it’s in the heat exchanger it would eat through that bitch, we don’t sell many of those around my parts but I personally have a Rheem tankless and as long as I clean it once a year I’ve been good

People don’t understand how Acidic condensate water is out of a high efficiency furnace, I’ve seen it eat rubber hoses on pressure switches to breaking down drains when dummies use black iron and galvanized pipes instead of pvc

👍👍

Made in china ?

Why Is This Brand New Furnace Not Heating? "American Standard" Well there you go, theres the problem.

The prime rule of ownership , maintenance pay me now or pay me later . Part 2 pay me later is ALWAYS MORE EXPENSIVE and potentially deadly!