- 56
- 40 097
Jimmydoinstuff
Приєднався 5 чер 2013
Yoooo welcome to the place i do stuff
Can the Flashing M & S and Limp Mode be an Easy Fix on the Landrover Discovery 2?
We are gonna find out how easy working on a Discovery 2 can actually be. I had been having a on going isssue with the truck going into limp mode and the M and S flashing on the dash. After some research and a new battery I came to the conclusion my XYZ switch has become faulty and needed a “rebuild”. Follow along or just enjoy watching thanks!
#landrover #discovery2 #carvlog #mechanic #restoration #rangerover #project #asmr #4x4 #diy
#landrover #discovery2 #carvlog #mechanic #restoration #rangerover #project #asmr #4x4 #diy
Переглядів: 54
Відео
Will These 3d Printed Parts Fix my Land Rover Discovery windows?
Переглядів 297Місяць тому
Is your disco 2 windows going slow, popping, or jamming well nost likely its because of the shity plastic roller design. Here i 3d print some new ones and see if i can get them to work! If you need some hit me up!! *note I been rocking these and they have been working for weeks at this point now #4x4 #mechanic #asmr #landrover #discovery2 #repair #maintenance #restoration #carvlog
2004 Land Rover Discovery 2: Headliner Removal, Sunroof Motor Rebuild, Roof Re-Paint
Переглядів 1,3 тис.Місяць тому
Heyy yooo enjoy!! Sorta the season finale to the land rover, more videos but shes back and I will be dailying it! #4x4 #discovery2 #landrover #carvlog #asmr #british #automobile #mechanic #build #project #restoration
2004 Land Rover Discovery 2: Inner Axle seal install, Front Wheel Hub Install, and Wheel paint!!
Переглядів 1432 місяці тому
Welcome to the struggle i show my method of inner axle seal installs and put the new hubs in…twice (route the speed sensor under the carrier. And paint the wheels! #asmr #automobile #landrover #discovery2 #british #4x4 #mechanic #restoration #carvlog #project
2004 Land Rover Discovery 2: Front Hub Disassembly, Ball joint install
Переглядів 1703 місяці тому
Hey! Enjoy the new video. Landie is coming along great, in this video i dismantle the front hubs and install the new ball joints. This is up there in difficulty especially removing the old ball joints. #carvlog #mechanic #build #landrover #discovery2 #asmr #suspension #4x4
2004 Land Rover Discovery 2: Thermostat Change, Dash Peel Repair.
Переглядів 6174 місяці тому
Enjoy! My pain and and discovery something new about yourself. Attempted the leather repair but its too cold and repaired the dash peel using lucky 8’s repair kit. I also changed the thermostat to a new lower degree one. #mechanic #carvlog #discovery2 #landrover #restoration #asmr #build
2000 NB Miata: Install Adjustable Control Arm, Fender roll, and NEW WHEELS?
Переглядів 3074 місяці тому
Waddup!! Tried installing second hand adjustable control arms, nope! I actually ended up selling them. I will go a different route using offset bushings and extendo lower ball joints. Rolled fenders as prep for new 15x9 0mm offset wheels! You can get that fender roller from amazon! Enjoy! Subscribe and like if you care!🫡 #miata #carvlog #mechanic #driftcar #build #slammed
1971 Karmann Ghia: Seat removal, Seat Reupholstery
Переглядів 4035 місяців тому
Waddupppp! Hope all you lovely people are having a lovely life. Here we are learning how to remove the seats and reupholstering them!! Enjoy, comments or suggestions are appreciated. #mechanic #karmannghia #classiccar #car #volkswagen #restoration #howto #reupholstery
1995 Honda cb750 Nighthawk: Creating a Custom Offset Front Sprocket
Переглядів 2,5 тис.6 місяців тому
The story goes i started with a hand made front sprocket i ground down and welded, and it has a nasty wobble causing the chain to bounce excessively. So I made a new one with the help of a machinist friend! Chains on a stand will have some shake due to no load (from the road) i have yet to road test the new sprocket. I will do a separate video of that along with a suspension/ carburetor tune. L...
Karmann Ghia: EMPI Dual Carb install, Dash, Light Housings (FIRST DRIVE/ BURNOUT!)
Переглядів 1736 місяців тому
Yoooo welcome, thanks for watching in this video we install the plastic dash cover, EMPI Dual carb install and perform modifications required to complete. Little bit of 3d print stuff, anddd put all the light fixtures in. Finally making progress and i can wait to show you how well it is now since this vid is 3 weeks old. Love you please consider subscribing and liking Discaimer: i dont actually...
How to do an Oil Change
Переглядів 366 місяців тому
Oil change on a NB Miata Items needed: • 4Qt of 10w30 • Oil filter • 17mm Wrench • Oil Catch Pan Super fast and easy yah. #car #mechanic #carporn #carsarepain #carcare #oilchange #carasmr #miata #nbmiata
Karmann Ghia: Speaker Stuff, 3D Print Stuff, FIRST START!
Переглядів 1597 місяців тому
Karmann Ghia: Speaker Stuff, 3D Print Stuff, FIRST START!
Karmann Ghia: New Gas Tank Install, Wiring
Переглядів 6358 місяців тому
Karmann Ghia: New Gas Tank Install, Wiring
Discovery 2 X Karmann Ghia: Fuel Pump Access, Engine Wiring, Paint Prep
Переглядів 3088 місяців тому
Discovery 2 X Karmann Ghia: Fuel Pump Access, Engine Wiring, Paint Prep
2004 Land Rover Discovery 2: Changing Spark Plugs, Wires, and Coils
Переглядів 2 тис.9 місяців тому
2004 Land Rover Discovery 2: Changing Spark Plugs, Wires, and Coils
Karmann Ghia Restoration: PAINless Wire Loom Install
Переглядів 5129 місяців тому
Karmann Ghia Restoration: PAINless Wire Loom Install
Karmann Ghia Restoration: Gas Tank and Wire prep
Переглядів 63410 місяців тому
Karmann Ghia Restoration: Gas Tank and Wire prep
LEGIXN-T O R I N O K O S A (prod. lil Biscuit) **MUSIC VIDEO**
Переглядів 435 років тому
LEGIXN-T O R I N O K O S A (prod. lil Biscuit) MUSIC VIDEO
achillez- R A I N (Prod. dead spyro) *MUSIC VIDEO*
Переглядів 1535 років тому
achillez- R A I N (Prod. dead spyro) *MUSIC VIDEO*
JIMZ and Friends Skimboarding Delaware
Переглядів 2938 років тому
JIMZ and Friends Skimboarding Delaware
Came to find out how to get a seat out, stayed for the twerking
So glad I had my intake and valve covers powder coated
Would you mind sharing the STL for those parts? So I could print it myself, only for personal use.
@@blazer83ov sure thing! Whats your email?
Yo I'll take a set or two of those things if you're still doing them.
I just fixed my XYZ switch when you first start it’s a pain but now that I’ve done it. It’s a piece of cake now I just have to get the three amigos off the dash.
@@mcleodmarcel48 is it shuttle valve issues now for the tres amigos? I just filmed a new video repairing mine and that completely rid me of the lights while retaining function
Great video, thank you! Keep them coming, we need more disco2 videos 🎉
@@canonburymerkez5520 thank you! Got ome actually coming tonight! Stay tuned
The tires look so hilariously small hehe
Howd you make them fit?
@@antoniomora1739 pulled the inner wheel well guards out and did a fender pull, front camber is maxed out negative on stock adjustments and rears have max positive camber
What kinda cage ?
@@Junkjet00 zereke fabrication out of cali, its the clubman package
@@Jimmydoinstuffthanks
@@Jimmydoinstuff does it work with soft top?
@@Junkjet00 oh yes works great, gotta cut some shit inside but if youre strategic it looks pretty much oem. Zerek actually has a very helpful video on his page here thats what i used to install
😂🤣
alright the gasoline part got me... What kind of paint are you using for the top? why not use an hvlp set up ?
Hahaha sometimes i wish it was gas, and im using touch up direct its water based and a 2k clear, comes in a kit. I was going to go hvlp but i dont have the set up or the patience to figure out it out whereas i rattle can all the time soooo… cost and familiarity is why. Turned out great and has been holding up good tho regardless this summer.
@@Jimmydoinstuff no doubt it looks great. I will be tackling mine soon. Thanks for the video on how to.
@@blakewilliams9642 thank you big dog! Good luck!
Let me get some of those my man, I tried a metal washer and I think it’s too loose!
Dm my insta with your address i will print and send you some!
Jimmydoinstuff
I miss my 04
the wheels turned out great tbh
Super, thanks for showing how you did the work on the head liner and the motor. Big help in understanding how to tackle the problem.
Yessir, save you big money if youre handy enough with great results😎 thanks for reaching out!
Best to pull the cloth off the headliner and use a metal brissel brush with adhesive remover to rid of the old foam, to prep for the paint. I took epoxy and brushed that onto it to create a smoother surface. Just a tip that i didnt show
Thanks! A few good tips that got me through the job! Hope to see what’s come of your rig
Glad it could help! Quite a change in performance too i felt.
@@Jimmydoinstuff I cracked the coolant vent valve housing (temp fixed), but all else went well, most maintenance done on the weekend yet. Fan belt too.
@@walker_skiesspencer7901 hell yeah brother yeah its ashame the amount of plastic stuff on these trucks and after all these years it gets so brittle but they make up for it in coolness lol
Yo what tire size are you running
195/55 R15 blackhawks best stretch imo😎 functional and still sorta of aggressive.
hey so how’d you get the tires to stop rubbing? i’m putting 15x9s on my 1999 to
My offset is 0 as well. I actually maxed out my front camber and removed the inner wheel well liners . Pulled the fenders till the puller was maxed. Cut the tabs that held the fender liner and the tab that holds the front bumper to the fender (need to get after market clips) rears i actually maxed the positive camber out so im sitting at -4ish degrees neg rear and -3.25 front tires are 195/50 as well. Lots of install and removing tires and alignment adjustments but i dont rub at all anymore
thank u sm!!!! i absolutely love how it looks
@@saintx5933thank you so much big dog good luck!
Corduroy killer!
Damnnn thats fuckin hilarious you got a sticker coming your way broski😂😂
Hit my instagram dm’s with your address @Jimmydoinstuff
Broken chair, you need to lay off the cake mate 👌🤪🤣🤣
Hahaha gotta stay caked up 😎
Did the exact same service, mine didn’t start back up :(
It certainly can be like that sometimes haha
Build sheet?
- 1995 cb750 donor/ motor - 2011 r6 forks with wheels and brakes - 2011 r6 swing arm with rear wheel - Full custom seat frame and body work - Full custom seat (foam board, fiberglass, surfboard track pads) - Drag jets and stock carbs, 3d printed intake runners to fix mid range lean out from the vaccum throttle in the mikunis - Stock exhaust cutoff mufflers 2-1 set up with stock resonator - Stock tank rear lifted 1.5” for levelness - Stock headlight retrofitted to r6 fork - no speedo but stock tach and 3d printed mounts - also had to fabricate a offset crank gear and use a lower tooth rear sprocket to get the correct chain pitch Really a budget build and had to get creative, i appreciate your interest😎
Build sheet?
thats some nice meaty rubbers you got there
I had to split the case in my 91 so now its a 830
I actually havent tried to open the motor up yet, whta did you do to go 830 that sounds awesome
Bored 80 over . Figured while I had motor apart might as well of spent money done it right
And I'll never open another, motor swap would of been wY cheaper
@@johncarrington1024 thats awesome dude id love to hear that if you got any videos, huge power difference? With my current tune/ exhaust, jetting, and intake its a huge difference
No video but got plenty before after pics
Is that motor have two internal chains? One from starter to cam shaft and one that runs cams also?
things coming along nicely 🔥
Oh i remember my 1st and last time changing the coil pack the same way you did. It sucks! On my 4th & 5th Land Rover after always trading up in years started with 98 now I have 03 disco & 06 LR3. Doing all the maintenance as well as major repairs on my Rovers. I learned a lot of easier ways of doing things. If you ever have to change the coil pack again go with the Coil Pack Relocation Kit - Land Rover Discovery 2 - ERR6045TWS Motors SKU:WSCPRK1 Comes with new Bracket and hardware, plug wires. It mounts the coils above the alternator. Video's are on UA-cam. I hope you keep it. They are great rigs. Good luck
Thats a great suggestion and im sure i will be in there again doing god knows what. I will definitely do that. And im keeping her for sure actuallu working on getting full brake kits and fluids for it, also talked to a coating company about a paint match gloss “line-x” for the top and fender flares
And you can leave the old one in place!
Im the nth owner of my 03, got it 3yrs ago, had all the dash lights on when i got it but it ran fine. I've spent more money than what I got it for but the heart doesn't think. It just enjoys the smiles per gallon everytime I drive it, 20k miles so far, many more to go. Take care of your truck and it will take care of you. Cheers!
I love that thank you dude yeah i fell for this thing hard in the little time i had it and short distance i driven it. I plan on getting full brakes and oil services then it will become my daily, maybe dabble in some suspension stuff but the stance is perfect as it is right now so idk
I had to do the coils on my D2...it suuuucked!!! I'd keep that bad boy if I was you...or sell it to me dirt cheap LOL! I love the white color, my X used to have a white one with tan interior. It was frikin mint. I have a silver one with the back seats removed to carry my bike inside. Favorite truck of all time.
Hahaha i love that dude, jealous a little bit about the tan interior thatd be mint. But yeah im trying to figure out if im going to do a 2”lift (i am definitley gonna keep it) i cannot find and stock shocks and springs thats not cheaper than a lift kit…. I love the stance now is the problem with my 265/60 r18
things wild, cant wait to see it on the street
Road test enroute🫡
need an update on said road test @@Jimmydoinstuff
@@Eanradke dudeee so i did a secret ride to make sure it wasnt gonna kill me😱 its insane imma try and get a vid next warm day
@@Jimmydoinstuff hit me up if you need help filming it 🙌
@@Eanradke bro i might actually need some help we should line a day up for rollers
thats dope af man!
i liked the way you fingered the oil filter 😏
Hahahahaa the sexual tension in this video
@@Jimmydoinstuff spicy 🌶️
2k in that condition. What a steal! I’m working on a similar project.
I thought so too dude! Super clean coolant and good looking oil it was well worth risk imo! What year is yours? And how many miles? Mines at 98k and and im nervous about the sleeves slipping at any point lol i hear hella horror stories.
not the corded drill XD
i hate dealing with anything electrical lmao
Its beeen quite the bitch
😂dude I was laughing the entire video 👌🏼 Discos will piss you off for good!!!
Hahaha thanks big dog! Yeahh shes been quite the gem, i swear everytime i start it i’m like ugh whats gonna break next hahaha. Im thinking about going for a full overland build on it and can only imagine how much she will like that lmao
@@Jimmydoinstuff Hahahah yes I’m the same on every start up looking at the ultragage what code might come up this time 🤣🤣🤣 Will wait for more videos on the Disco 👌🏼
@@sal1520 more are coming! I appreciate you bro🤘🏽
How are the head gaskets doing on that beauty
@@ccracraft32 its got 98k soooo im assuming they are good but we shall see i plan on doing a LS33 swap if she decides to blow on me… however the coolant was very clean before i flushed it and i changed the water pump and even put a 180degree thermostat in soo maybe thats enough to keep her healthy.
what color you gonna refinish it?
think we are either gonna go baby blue or that same yellow!
Or just keep it white! Seriously the truck looks beautiful the way it is. In the future white in a discovery two may be a little hard to find. It would be cool if you could do an LS swap on it though.
@@mcleodmarcel48 so i actually got a great coating company that im getting a quote from to have it coated in a “linex” material. And yes im keeping it white! Alsooo this motor gives me so much stress so it makes me happy to here the ls swap idea and if the videos keep getting traction, i will highly consider it or some other kind of motor.
@@Jimmydoinstuff oh, so you want some traction ay? I tell you what if you want some good traction do an LS swap.if you want to be a legend do a 4bt Cummings swap. if you want to be different, then do a Bmw diesel swap. It will also be cool if you swap the transmission for a 6L90e an pair it with a built LM7 5.3 or 6.0. You can nab one out of an old Escalade.
@@Jimmydoinstuff you should pull that motor out and rebuild it and sell it. The Bosch 4.6 is actually not bad of a motor it’s just that it’s an aluminum block with steel sleeves and from the factory they didn’t understand that steel and aluminum doesn’t do well together in an engine. It’s literally just an old Buick motor,but it was past time for that engine to die but still. It really wasn’t a bad engine. Land Rover just didn’t invest in the tooling.
Nice!i!!!
Thankss dude!
I love camaro! I have the 23 ss shadow gray metallic! And I'm in love❤❤❤❤
Ayy thats fire fuck yeah its a great car 🤘🏽
@@Jimmydoinstuff yessirrr!
Umm gorgeous 😍
My dream car!
Dreams do be coming trueee
Somewhere in Fla looks like. Around the 32993 ✌🏼
Close its actually Florida’s dumber little brother, Delaware 19930 hahah
Go back to the valley man
Good bye tires and engines
Hahaha😂 it likes it rough
@@Jimmydoinstuffayo 🤨
Is that the donought media money pit car
Hahahaha somebody get Jobe on the line i took his shit
The piece on the steering column linkage at 10:12 with the holes in it is designed to collapse in the case of an accident, it's designed to prevent the force of the front end collision from shoving the steering column into your chest like a spear and killing you... Prior to this era cars had solid steering columns, with no collapsible element, and many times in a front end collision the steering column would be thrust back into the driver with tremendous force and spear them in middle of the chest and kill them. This was VW's early attempt at a collapsible steering column as a safety feature. It sort of worked. Hope this helps.
That makes perfect sense thank you!
@@Jimmydoinstuff Yeah modern cars have a "Crumple Zone", this is sort of like a steering column crumple zone.
First woot😅😊 sick wave too btw
Hahaa thanks dawggie🏄🏼♂️
You look like the little Lebowski
Just looking through UA-cam and found this! I'm freaking DYIN!!!😂😂😂
Thanks for the comment!