Відео

Ok, perfect take down with great info and love the humor. For that exact Mikuni carb, where do we find a replacement needle or overhaul kit for this carb? I dare not attempt the part number for this carb but its something close to Jxx-14101-0x with the vent tube. I know the Mikuni is good so if i can just find the kit or needle, what do you suggest for tracking these parts down?

do all the gravely pro turn mower have the same bearing size I would like to order the bearing before I take it apart it's a pro turn 52 commercial model 991208

Nope. I replaced every single thing in my fuel system, new hose, new rollover vent, new gas, new filter, new carburetor, new intake, manifold, gaskets, new carburetor, gaskets checked for cracks. It does exact same thing hasn’t changed a bit.

You do not have to remove the black plastic piece. Just rotate choke plate towards you and the link can slide right out. Also there is a slot for the kill wire almost directly behind the choke lever. Snap it in or it can wiggle loose from its mounting position.

Hi thanks for the video is this one turn out low and two and 1/4 for the high apply for all sizes chainsaws .? Thank you

Great advice. Thank you

Very good job. Saved me from taking it to the shop. I’m going to buy some gas in the can tomorrow! Haha. Just a note…you can take the choke linkage loose if you twist silver choke up. It matches and will slip out. I did use needle nose for a light push, but works! Check it.

Thanks

excellent video, thanks!

I've watched six or eight of these videos on this subject and your's is by far the best of them. My parts are on order and my fingers are crossed. Thanks for the instruction.

I was thinking of putting a kit in the carb I took off, but only if you do a video on it. I don't trust anybody else. I am going to try to replace the carb and lines on an old Poulan Wild Thing 2375, hope to get enough help from youtube videos.

Thank you for this informative video. I did as you described and it cleared up the idle surge problem on my Kawasaki FR691V. Is it necessary to recover the adjustment screw access after making the adjustment? Thanks again.

Been a marine/small engine and millwright for over 30 years one of the best small engine videos I have watched. Very good job!

Great video, just what I needed, even though its late in the season I'm tired of pulling the plug & priming through the cylinder lol.

I had a hard time getting the the gland nut off, went to a local farm repair shop and paid them € 20,- to do the job ( for all 3 ) . They had a much better torch and a much better spanner wrench to do the job then I did. The rest is a diy job.

Is the o ring on the carburetor is it a SAE or metric cause my didn't come with one and the used one I got from e bay didn't come with one also

Where did you buy your kits?

This is the best repair video I've seen in a while. Very well explained.

How can I set the carb back to stock settings. I just replaced one and I got it all jacked up . I just need to know how to get it back to a good starting point

Where yu get yur cards at

Great video, thanks! “Shazam! Little bitty zip tie.”

Thanks a bunch man ,sure appreciate it ,the idle screw did the trick ! I had to remove the jet a blast it with some of that carburetor dope ! Lmao it musta have been clogged up .

Greatly appreciated, thanks!

Thanks for the knowledge. God bless you

I have a problem with mine just starting and gose off in a while

What blue fuel do you recommend? I use Trump Fuel from Ace is that good?

What is the little black plastic piece on the right side? I broke it off mine and now it’s surging, don’t know if it’s related.

Junk,junk,junk, that cost a whole lot more, morons😅

What happen if is no primieing or the the gas doesn't stay in the bubble

This may be the most helpful video I've seen on UA-cam.

Was all messed up with the throttle cable until you showed how it fit into the molded piece down below…thanks

Thanks ,,needed to adjust the screw,,,brand new .mower also.

Thank you. Your detailed video really helped.

This is a great video. The pouring out of gas and replacing with fresh fuel was perfect advice. I did pick up a new carb etc… on Amazon for around $20 just in case and will just save it. Great step by step video!

If you’re looking for a vacuum leak, spray bottle with water. Water gets sucked in, runs bad. Easy.

Wish I had seen this before a local repair shop soaked me. They replaced the carb and after a few hours the same problem recurred. Thanks for posting this video.

Crazy good video !! Thank you for being a great teacher!!

This worked exactly like you said. I was worried about drilling that out. Sure enough it fixed my idle issue! Hod bless you Sir.

i've got a hustler fastrak with a kawasaki fh580v Kai ... seems to run fine but you engage the blade it doesn't necessarily bog down but it doesn't rev up... but it will bog down and nearly die once u get in grass and ride very slow... New carb etc.. could this be me problem?

I'm surprised you don't have more thumbs up on this video! Worth watching and very informative!

You are doing with one hand what I struggle to do with two. I've watched all the youtube vids on this job, yours is so far ahead of the rest. The kill wire switch setup had me puzzled. But after a bit of study I think I have it now. I subscribed, and upvoted your video. Since I now rarely use the saws, I am considering going electric and keeping only one gas saw. Would you care to comment on that idea?

Thanks for the video. Just what I was looking for.

Bearing and grease gun is cheap and easy to use 😊😊😊

Know what's wrong with your video? Nothing! It's absolutely perfect (I partly stole those lines from an old Audrey Hepburn movie) and thanks so much for the best and clearest video I have seen on this particular model. Liked and subscribed.

Try doing a little clean up on it, before reassembly 😮

Thank You !

I knew this was going to be bad. Look at how he lifted it up.

Do not do this. Cutting holes in your mower is not the answer. Get a shorter, stronger spring.

Do you think this would help if my engine only surges when hot? (Normally about 30 minutes of mowing or so). I've replaced the carb, replaced the coils, replaced the fuel pump, removed the heads to clean them up and reseal in case it was a head gasket leak. I'm at my wits end on this one.

As if your instructions couldn’t be any more thorough, the choke switch and hole hack are the two cherries on top. Thanks!