Відео

How much bentonite did you use, mix ratio?

I'm trying to do the same at my house can't get it I got to 24 feet and it won't go farther I don't have 5000.00 dollars to pay the man and I gotta go 120 feet I don't know what to do

When you started the machine to push the rod out of the cylinder did you do anything other than turn on hydraulics?

I used 38mm drill rods hydraulic motor pressure cleaner feed water on a forklift drilled 12m gave up spent $6500AUD got mick miles waterbores out 63 m done ready to pump in 3 hours.

My interest started from a shop class in jr.high. we were given a little lawnmower engine and had to dismantle and reassemble

Thanks for the video. I need to replace the pressure hose on my '02 Dakota V6.

How did you address the attic insulation after you installed these? what considerations need to be taken when it comes to attic insulation and these units? for example, would rolled insulation be laid out around the unit, leaving a square opening around it?

Extremely bad approach, just get a powerful water source and see what it can do to the ground

I really liked watching from an angel where I couldn’t see shit love it thanks

Any ideas for an 873 with a bad joystick and no replacement part? There are aftermarket ones, but the wire colors are different.

I'm with his wife. Does he know how deep down underground (where you can't see) the clay goes? This, at least, proves to me that my wife is not the only female who asks the most ridiculously absurdly nonsensical questions while in the midst of a strenuous, stressful task.

Your daughter is enjoying her mud puddle very much. And she's a wise young lady in that she's wearing rubber boots, unlike some adults around here. But heh, with the money you save from not hiring a pro well driller, a pair of ruined leather boots is cheap.

When you say run it for 5 minutes and then “let the engine cool off completely” how long is that cool off period roughly?

What a piece of cerap😢

Doing what you did is a risky proposition. Many attempt, some succeed. But the result is not what you would get with a professionally drilled water well. They have equipment to wash out the fine sand from around the screen which is a huge plus. Additionally, a well screen in a professionally produced well can be pulled and replaced.

Steve cool video I unplugged all wires from that harness I forgot were they go do you have a wiring diagram thanks

What state are you in, Florida?

ahshahahaha

That's a back breaker

turn shaft backwards

I see Jr loves to ask stupid questions at the worst times.

Do not try this method in glacial till!

I can see that you are the one that cut that pipe and caused the damage.

I especially liked your design of the tip of your dril pipe using galvanized steel pipe.

Man, l absolutely love ❤️ your attitude! And your persistence and perseverance, not to mention your family who stood by you 🎉❤

Just for info; sometime near 2019 Bobcat changed the "problematic" check ball pick up tube design and switched to a "primer bulb with Check ball in "it. I would just switch all primer bulbs :)))

You know they make a 4 foot extension for gas augers right? Turns 4’ into 8’ or 12’

Dude I’m not going to Monday Morning Quaterback a thing IMO this entire Process was pretty Impressive , no matter what you attacked itvAggressively and came up with a possible Solution Yet Continuecto give it the Hard Work until Success

This has to be the best oil change video I have even seen.

Hi bloke found this water drilling method so you don't need to backfill Cheers 🥂🥂🥂 ua-cam.com/video/3pOSzBgB8WU/v-deo.htmlsi=7gR5g6LGhEHSAWZl

There goes his back

Did anyone notice that you could just keep holding the power on the auger and it would come up while you pull. Like drill , stop drilling and big gets stuck so start drilling again and pull out.

I WAS WONDERING HOW YOU ARE LIKING THIS MULCHER NOW THAT SOME MORE TIME HAS GONE BY. ANY ISSUES? HAVE YOU HAD TO REPLACE ANY TEETH? HOW MANY HOURS DO THE TEETH LAST AND ARE THEY EXPENSIVE TO REPLACE?

Yes, deep breaths

5:10 - drilling teeth

Super cool dude, shocked pvc held up to the torquing from drilling

Did anyone get this to work?

You need to circulate a clay/water mix going into the inside of the pipe and returning around the outside of the pipe using a 2 inch or better trash pump in order to stop the ground from collapsing around the pipe and freezing it in place. Dig a big hole next to the well (mud pit) and fill with the slurry and circulate it while drilling.

Hello, i have questions/concerns about isoscell. Are they legit and on the level? They responded to me via text message and now they want money sent through paypal - seems like a scam. Please advise - thanks

Should of used galvanized steel pipe when drilling

HELAL OLSUN.Çok güzel iş.

You got er done so good job. FYI, water volume is more important than water pressure. Two hoses sealed off so the water and sand/dirt/cuttings have to come up out of the hole not back up the pipe. And go sloowwwww. Let all that dirt/sand come out up away and you wont get stuck.

Sadly my soil is mostly rock..

You need an office job.

How does it do on palmettos?

I have a question, my don't leak but the boom won't stay up will.slowly come down making a cracking sound same bobcat 763 any help would be appreciated

Use your legs, not your back to lift.

Using bentonite?

You are going to injury your back bending over and pulling upward that way. Use your legs more.

You hurt my back yankin on that auger