Відео

Wonderful instruction. Can you please share what cold working you had to do?

Thx so much for this video. Did you cold work your cut edges before fusing them?

Great video , Can you please advise if you carry these relays in stock ? I have an Olympic Gf2eTLc 20 x 20 in kiln that has a Bartlett RTCc1000 digital controller that is showing an E-d error ! The manual is telling me it is possibly a relay issue . Sorry to contact you this way . Happy to email if you can send Many thanks Dianne

Interesting. Bartlett told me my boxes were too small. My insulation melted . Mine look bigger than that. 6”x 9”

Thanks

Can we see your jewelry for ideaas?

0:18

Ok, I’m SO new. I haven’t even fired my kiln. Can I use high fire for every project?

great video but surely 20 x 20 = 400?

tks the video. The temperature is in celsius ?

Just fired my new kiln , thanks for the video!

How could I order the kit?

Haha..."being prepared is for the weak." Too funny.

Love it

Where can I buy a build your own kiln for a descent price

Good morning how would this lace work fused onto that white glass then slumped or draped

What’s cost for kit

What is the best price for this kiln ….what is the highest temperature….what is the size of the kiln

HiHow can I order the whole kit and how much does the temperature controller cost?

mix your primo in advance, and spray it on with a auto-body paint sprayer... For best results.

Thanks! 🎃is there a way to add Wi-Fi to it? Like with a Raspberry pie?

Where to buy these kits?

Would love if you could show finished piece. Is there a way you can share in the comments?

wonderful, could you put the curves of fusion o tack fusion please ?

Can we slump glass in this type of kiln?

Amei

Thank you for sharing. It's very exciting and inspiring..! |🇩🇰 🌠 | 😉👍

how did you make the channels for the elements please

Can you advise what material you used at the bottom base of the kiln

Use this on your next Ds3 play through

Only one problem: 20cm x 20cm is 400cm, not 40!! So at 2g frit per square centimetre that'd be 800g frit, not 80.

Please send me your email address

use the tile saw instead of the hammer

What size frit are you using? Coarse, medium.or fine?

Where can I get the first firing info for the Bartlett controller model3 K?

Hi Dave - responding to your email too - but just in case someone else has the same problem.. not really without a relay tester that can measure current (which costs a lot more than relays). The best thing to do though would be to measure the resistance of your elements if you have a multimeter and feel comfortable doing it. For a 240v kiln you should have 22-23 ohms of resistance for a 10 amp element group, or 11ish ohms for a 20amp - for 110v kilns 11 ohms will give you 10amp, and 5.5 ohms will be for 20amp... anything away from these numbers suggests you need elements rather than relays. It could also be your safety switch if you kiln has one of these. If you aren't sure - relays are cheap and easy to swap.

Thank you for the video! I have the same model Cress. I suspect the relays need replacing. When I do a test run…ramp at 9999° up to 1000°…the kiln only heats up about 10°-15° per minute. Is there a way to test the relays? They’re not too expensive so I’m thinking I’ll just replace them anyways. Thanks for any info.

Where can I buy one of these kits?

No se entiende 😞

Great video. I am new to glass fusion and am making a coral bowl. Thanks for the information!!!

I am interested in building your kiln but would like to add a 4-in bead window at the bottom

Do you find you need to sand/blast/do anything to the cuts before you fire? I read somewhere that you get a haze if you don't, but I don't see any other artists doing that. Enjoyed the videos, thanks!

Can I tack fuse the lace to a solid piece of glass

Thank you for the video

This video was super helpful! Thank you!

Sou brasileira e queria muito um forno desse , sonho ,sonho de consumo

Should i coppy this for a bisque fire

I'll throw that control box in the garbage where it belongs, I would never ever press that many times to program it. A simple phone app connected via Bluetooth or USB connect to laptop or desktop is much more time saving. Would rather spend extra money for such simple microcontroller like Arduino which costs few dollars.

Jeeze this is really a hectic work, a lot of sanding, chiseling and massive repetition of measurements. This is the best DIY video for building a kiln, thanks for the effort of getting good shots of the build process. Is there any alternative to calcium silicate board? Can you add ceramic fiber wool instead of calcium silicate board, will the efficiency still be the same?

Can you make a video on how to build a natural gas forced air glass kiln? Is it too hard? Also can this design structure and materials also be used for a natural gas modification? The reason I ask is because I would like to build a glass kiln mainly for annealing glass, would like to make nixie tubes.