Відео

Can you tell me a have a BSA A65 1967 There is a hole in one comrod what side drive or timeing side What happens if fitted to wrong side

Where is part 5?

Those jeans a little on the long side!

i use to go to srm when there were at penarth nr cardiff

This is one of the finest motorcycle museums in the world and nobody talks about the fact that this Museum burned down and within a few years all motorcycles were replaced except for one. There was a display of the burned area behind plastic walls that showed how bad the fire was. It is truly a gift to the motorcycle enthusiast and is the way a museum should be run.

How much compression must have a 1967 bsa thunderbolt 650 cc?

I wonder why the engine is not in nice engine stand

srm used to be good now just average would never use their tsb con

Well, I wouldn't use the torque wrench for normal spannering. Specialists are they?

I'm trying to remove the centrifugal filter from a 1970 A-65 crank. The slotted plug took some work but now the tube inside does not want to come out. Anyone have any tricks on getting these out?

I rescued my mate twice with broken crankshafts on his A65. Devi or SRM work is mandatory.

Thanks for the demo .. love those three bikes

👍👍👍👍👍👍

Beautiful nice

Good I am Pakistani Sajid Bhatti beautiful bike❤️✌️💯🇵🇰🇵🇰🇵🇰🇵🇰🇵🇰💖💖🧡🧡💙💙💝💝🥰🥰💚💚❣️❣️❣️😘😘💕💕😍😍😍😍❤️❤️❤️🤍🤍🤍🤍💟💟💟💟🤗

Do these guys fill the crank with oil before they balance it? I have never heard of anyone who does this and I’ve always wondered why not just curious.

traductor plis

traductor plis

Conrods are 50 to 60 years old and are best in the bin. Billet conrods are the way to go. Just my two cents.

Talk, talk talk..nothing gets done

4:20 jumps past the rocker shaft removal. How do they come out? I tried tapping our right to left but not getting any movement. I don't want to get very aggressive with the Hammer!

Are we sure that isn't a 750 already, those pistons look huge!?

Yes definitely need a re-bore if it is going to be a 750. Perhaps a re-sleeve to aye?

I had a '64 model thunderbolt and I replaced all the rocker cover fixing hardware with newly made studs that had BSF (lower half of the stud) and 1/4 " (above) and nickle plated dome nuts. BSF was terrible to work with, given the various range of sizes and I couldn't get tools to suit. I generally used metric substitutes and muddled through.

Is that a pre '66 model?

Love it. Reminds me of learning about Ducati quadrant kickstart gears the hard way. Bump starting in winter Edinburgh etc, But sussed it and got very lucky with Walkers in Norfolk

Love A65

How come there were no cam followers fitted when the barrels were removed? This engine had been loosely assembled just for the purpose of this filmed stripdown, hadn't it? Nowt wrong wi that but why not say so at the start?

Lead free valve seat conversion? What is this and what is entailed? (and how much does it cost?)

Good video. I would suggest that it would be much better if the camera was closer to the parts . A picture is better than a thousand words.

Awesome! They truly show you in-depth what to do. Thank you for your video. If you ever want to come to Ohio, you have a place to stay and a free ticket to the motorcycle museum in Columbus

Fascinating my mate had an A65 that broke 2 crankshafts, both times coming to see me. Hello Devimead.

It would have been great to hear the SRM people, If your going there to use their technical skills why talk over them all the time. Aren't they the experts?

Still recon one of the best BSA motors ever. A treat to work on.

With all due respect to SRM because I know they do great work , why is the crankcase not held in a jig ? It would make disassembly much easier and safer .

BSA cut corners, fixing these bikes would probably not be cheap.

Very well done!!!

what about the triumph Tiger cub

Alloy clutch pressure plate a great piece of kit for BSA and Triumph

I had a roller bearing job done on my A65 and resulted in to much weld that interfered with the Boyer electric , stopping the plastic disc from fully rotating , ie bike would start every kick then stop , Took a bit of finding and sorting out , I did message SRM about the problem but never got a reply ?

one day my a10 that you can see in my avatar will be there in the meantime back to the shed

I'm loving your videos! Have several A65s.

Ok.. video #1 shows top end disassembled. Video #2... starts at removing the primary drive parts. What about the timing parts. I’m trying to remove the auto advance plate. Manual doesn’t explain a lot

SRM = Such Ridiculous Money Very expensive

SRM, that reminds me of a time many years ago when i took one of the founders and his girlfriend back to Penarth from London with, if I remember right, a BSA single 500 that had broken down. Happy days, i seem to remember being fairly impressed with their set up even back then.

Great stuff...better to film the whole strip down,.narrate over the top and some close ups would be better though,..imo

Thank you so much. Great to see the experts at work and get some tips before having a go at home. Most of us don't do it often enough to remember the pitfalls. A fitter turner friend of mine said you don't need a micrometer. On an old Brit bike it's pretty obvious when something is worn out. Back in the 70's I could rip these down and put them back together in an evening. The alternative was catching the bus to work.

I cannot speak highly enough of SRM: I've had several jobs done by them, from cylinder rebores, complete head refurbishments, balancing, etc. and the quality is absolutely world class, flawless. I love this company and will always keep going back to them when I need something done. Thank you Rick and CB for giving us a peak into the operations.

Great work. Looking forward to the next video :-)

What crank is that in close up at 3:00 min? Multi cylinder?