Відео

Can you use the 3pv with this servo?

What’s up it’s me Markus

Hello my friend, quick question. Im new to drifting and im still learning my 10px and while watching your video i could not figure out how you got to those screens on your 10px so im assuming those are extra setting you only get while using a futaba servo? I have the futaba GYD550 but not the servo. Thanks

hello sir, sorry I want to ask something, can the 1:10 2wd buggy diff gear be applied to the rdx to replace the kit's default lockdiff? examples like yokomo yz2, xray xb2 & team associated b6.1? Thank you in advance for your attention & answers🙏

Great video. I built a Unicon01 with a lot of the same principles. The roll and pitch was awesome with what I build and its nice to see someone else do the same. Changing roll center is an underrated method to have more fun!

This is awesome video. Have you made a Sanwa MT-R FH5 transmitter setting?

Thanks for a great shock rebuild video. The only other thing I’ve seen, which is done by x-ray is they thread the shock shaft through the O-ring and twist it rather than just push it so it doesn’t tear the inside of the O-ring. Might be worth trying.

What type of grease can I use?

Thanks for the vid it was a life saver! SR mode FTW!🎉

cant you just plug the sbus adapter directly into the pc updater? looks like the smaller conversion cable is pointless. timeline 13:08.

Hi Mitch I have a question is the cd700 compatible with Reve d revocable gyro? Or only with gyd550 And can I run it without SBus? Cuz I have RPX2, Reve D revox gyro, agile 10.5 with 10PX version 8.0E Thank you 🙏

Nice roll

Late to the party but wanted to share an additional step. Once the limit on the gyro is set, go to the steering end point on the TX and turn it down until the steering throw matches the front wheel movement; for example, my steering end point (left and right) on my TX is currently set to 60. Skipping this step could make the steering feel too fast. This also needs to be adjusted whenever steering settings are changed on the links, servo, and gyro. Otherwise good video and thank you for the resource.

Can you do a video for beginner electronics for this kit I want to start rc drifting but I’m lost

What ESC Setup do you use to make the car so snappy? 😍

For anyone having violent shakes with the high power Futaba Servos (even with the servo direct to the receiver, bypassing the gyro) try changing BEC in your ESC from 6.0v to 7.4v, worked for me.

This was awesome thank you. I wish I had this before I get rid of my shark.

Hell yeah, Mitch! BTW, thanks for all your help with my RMX. It’s a damn good chassis.

Thank you Mitch! I’m glad you made this , It really helps me to understand. 👍

Mitch, you’re a lifesaver! I recently picked up a build that has a CT701 and the hunting has been so hard to track down. Gonna take some notes here and give it a try, anything you’d add for the CT over the CD series? I’ve heard it might need some more dampening from specific folks. Thanks again!

Can you setup the gyro to send info to the transmitter so you can use it for two steering servo's?

Thanks mate! Great info

Did you have to change the receiver to SR mode as well? I’ve got the same set up on two of my cars and my shark hunts so bad with this set up. My SD 2.0 doesn’t really do it but my skark oh man lol

I'm wholly convinced that there are defective and/or different firmware CD700s out there. My CD700 at factory setting would shake violently even just sitting at neutral with the gyro turned off. I have to run my stretcher in the 0.250-0.500 range as well as damper in the 150 range for it to work smoothly.

Soft start is exactly as the name implies. It only affects the servo when powering up, it will bring the servo to center soft and slow. Since the gyd550 does the initialization twitch, soft start doesnt really work. This is more of a setting meant for aircraft or grip cars where you wouldn't want the servo to snap hard and fast to center when powering on.

Definitely need to get a Futaba servo

So glad to finally have some good info on programming these servos. Now I can start playing around with the settings

Street break is my home track! Shipping my car out to you guys today man looking forward to seeing what you can do man! Absolutely cannot wait to get it back and see how it runs

You do not need 400-700 dollar controller to use this gyro! Good video but for people just getting into the hobby this is so false. With all respect, you can use this gyro with a futaba 3pv or an even cheaper one. It will still work flawlessly, you just can't use all is settings.

❤❤❤

Soy keylor

Papa ray

Hola

Would this work with T4px?

'promo sm'

Amazing job what cleaner can I use to clean the parts before I start ? Is it a special cleaner or can I use some alcohol?

great video and explanation I have in both of my Galm's a C-LSD and really like the way they work and drive

That's a good No nonsence video. Thanks for putting that together!

What's the spec tire there?

Hello dear, thank you for sharing this video, you make my life so easy, so I have to purchase the Futaba CIU-3 usb to update the gyro? Regards.

Great video guys! Tre seems like a really nice guy and you can tell how much he enjoys RC. Great interview and video all the way around!

Respectfully…. Sac is not The Bay!

My guy Tré!!!! Much luv!!!! And S/O 2 RG

wish the scene in WA was good, just got my first D5 today

Good stuff guys