Відео

Why carnt you just pull out the spring clip,and then pull the sensor up and then it comes out

Where did you get your carburetor

How many miles were on that old tire? Got your money out of it! Thanks for the information.

580bts markiii aka Redmax ebz 8560. Big game changer from by br 600.

Did you mount and balance the tire yourself or have someone else do it for you?

Best video ever...next best thing would be having a shop do it. Thank you... video was right on!!!!!😊

Dah. It’s a Leatherman. They practically invented the pocket tool. They bend over backwards for us guys that are so dumb we have to work with our hands.

Thank you! I misplaced my manual and this was a huge help.

Thank you! I did not know this.

Hello, Are you interested in testing our products? We would like to invite you to test the Full Windshield for your Yamaha Rhino 700 （ if your car year is 2008-2013

The inner cutters are for stranded wire, which tended to bind in the main cutters for me. I used them to great effect on semi trailer cable seals if they weren't zipped down so far I can't get a handle in it. Bicycle brake cable works well as well, if you ever need to replace your lines like I did.

Those lines on the top right of the reticle, what exactly are they for???

I found one of these in the Arizona desert. Thank you for this demo. Very informative!!

I just bought the same gp6500 like new but wouldnt start. I sprayed some gas into the carb throttle and it started right up so i oredered a new carb I may clean the original one and store for next time. Great video. My carb should be here today bought it on amazon. I need to drain tank and change fuel filter. What did you do with old gas is there a guicker way to empty tank? I may remove it and change plug as well. Great job.

My wife got me one haven’t stopped using it

Just undertaken the same job of removing the rear wheel on my 2000 year GL1500 SE. I encountered the same issue that you had with the splined coupling not freeing off with the wheel. I assume it was the ‘stiction’ of the grease that was holding it in place. It took me a while to work out as to why I could not remove the wheel as it was catching on the drive pins that protrude out from the coupling. It took a bit of doing but eventually I managed to slide the pins into the wheel and this enabled me to remove the wheel from the bike. My tyre choice for the bike was an Avon Cobra Chrome, I also will be fitting a matching Avon tyre to the front wheel as both tyres are old and have numerous cracks on the sidewalls. Regards from Nottingham U.K.

How big you going to let it get?

I’m thinking of doing this. Very good informative video. I have a 6500e and I mistreat it. I power my fifth wheel and the new house under construction. It’s running 12 hours. I think throttle is open. High rpm sounding and sucking up gas

16 pieces at 65 dollars each!? You must be nuts! 🤣🤣 I know what you meant just giving you grief 😅

wtf

Anything? 😏

Looks like he ate another frog too

Bull frog, doing It again! Some kind of happiness is measured out in Miles! What makes you think you're something special when you smile

Couldnt frogs breath through their skin?

Rip

R.i.p jeremiah

That's exactly what I was looking for, my actuator was broken so I was wondering if it's okay if I manually keep the valve open? if not, why not?

Imagine loving your country to death (your government would kill you in an instant if ot meant lower taxes)

Be Flying Old Glory HIGH AND PROUD THIS WEEKEND

Broke people is not patriotic?

Cool, wish the UK was a bit more patriotic.

America excels in engineering tiny little flags. Finally something to be proud of

Very good job. I may try doing mine. Thanks

I enjoyed, Thanks. Doing my Valkyrie.

If the gun is in decent shape you can load smokeless rounds to the same pressure as BP and it's fine(we are taking cartridge guns from the late 1800's, don't ask my about anything not made from steel). The issues arise when people use guns in questionable shape or try to match CUP rating instead of psi which, although correlated with eachother, measure average pressure vs peak pressure so isn't the greatest metric to go by. Basically you can use fast powder at reduced velocity to get the same pressure as bp eg bullseye, or you can use slow or very slow pistol powders to get more power and at bp pressure eg unique and especially alliant 2400 which in my opinion is too slow to burn efficiently at 6-8000 psi so half the powder will shoot out the end and you will have inconstant velocities. I prefer relatively slow pistol powders like vhitavori 330 or 340 which burn cleaner than unique but are as slow or slower and are nice and low in pressure on my load calculator, also they fill a lot of the case so you can't double charge them.

President McKinley was assassinated with the same firearm in 1901 while in Buffalo NY. A small plaque marks the spot...

I don't think catastrophic failures are what will happen with smokeless, more like they just get loose to the point they don't function. My guess is what really kills these top break .32's is dopes putting .32 ACP in them because it's the cheaper, most common .32 and it's way over pressure. Smokeless .32 S&W in the non smokeless top breaks seems to be fine for limited and infrequent use.

Promo_SM 😬

i have a dinosaur of a saw . an old 70's era Stihl 08. i learned to cut on this saw and would love to get it working again. unfortunately i was told years ago that the parts i need are extinct. or harder than rats teeth to find. I'm not good with small engines myself and would like some advice

I imagine that after sitting for so long the diaphragm was stiff as a board.

Worst camo ever made

Taken care of the 026 is a great saw. Love the older Stihls

Did you sharpen the chain properly 😮you might have to take down thr runners

I mean its like common sense really dude.......come ON!!!!

And where did you get this?

Ur garage is not messy compared to ours, lol. I’ve had 8 projects going on at a time. Nice

Top-break revolvers have long since lost the favor to swing out.

Not a lot of money in flipping saws, for sure. Go for higher priced items!

Wanted to thank you very much for this video because it helped me to fix my heater which was similar to yours. I ordered the same switch from Amazon and it fit like a glove. One thing that you might want to know for future reference is that on top of the panel where the switches are in the recessed area there is a large screw which if you remove it you can take the whole panel off and get access to the wiring that way. If anything I was able to remove some dust and debris that was inside of the panel and also to use WD-40 to pull off the Spade lugs easier. It also helped me to remove the old switch easier. Thanks again.

I've read that this is the same machine, besides plastics, as the redmax 8500. Can anybody confirm or deny this?