Відео

just found the video i have 2 of these little gems one of them has all the paper work from the 1st owner got lucky on that very good little diggers

How the throttle works on this tractor? As I understood from the manual you just using a clutch to move or to stop the machine. Is the throttle lockable, so you don't need to hold it depressed all the time? Getting ready to use my new machine, but I'm a newbie to a such kind of equipment. :)

What tires did you use on it? My tires are in a bad shape, would like to find an affordable replacement for them. Thank you for the video.

Wow thanks for demo

I like your idea of the electrolysis bath. I use a lye bath for stripping paint. I saw the idea in a car restoration book years ago. Its basically a 30 gallon drum with a 240volt heater band that you add about 8 quarts of plumber’s lye. It will get to boiling temperature and you use wire to hang parts on the lip. It will take every bit of paint off, but not rust.

I was wrong about using the saddle to adjust the angle of the plow, Darbradtrac made a comment to me that the bolts on the roller plate were there to adjust the plow angle ,he was right I have been using the wrong adjustment method .

Very nice and doing good work. Brother from another mother

For petes sake, pick up the rocks!

Where did you find parts

late summer(aug-sept) of 1975 confirmed

If you have to run on partial choke, try backing out the main carb jet (under the bowl) a 1/4 turn. I have the same tiller, it's a gem.

You need a snow blower attachment

This was built between September and October of 1975

I love craftman everything I own is craftman but now because everything I got is so old they don't make parts for them any more nobody around yo fix them either do slowly ill have to junk craftman find something else

I bought a "used" one for the snow here in West Michigan a couple of years ago. I only use alcohol free fuel in it, runs great, looks good. Starts first pull.

I am sure that some one has mentioned about adjusting the Youk that holds the plow , but I will say it again, RAISE THE LEFT WHEEL ABOUT 3 TO 4" ON SOME BLOCKS AND WITH THE PLOW SITTING ON A LEVEL FLOOR , ADJUST THE YOUK SO THAT THE LAND SIDE IS VERDICAL AND THE BOTTOM IS FLAT ON THE FLOOR, doing this should help to keep the plow following straight behind the tractor. And always use the smallest pully on the motor you can. Water in the tires could help.

To keep the plow from going to the left , you might try this , on a flat surface put the left wheel on a 4" block and adjust the saddle bolts so that the plow sits level with the floor . now the plow should be level when the right is wheel the furrow.

Got a lt1000 2000 and it’s got a 46 in blade on it yeah it’s a bit big for her but she still rips

Summary: He had it 5 years. light surface rust - good condition. Added fuel cutoff valve for summer-izing. No air filter. Reliable engine. Paint issues under the intake, but he picks up gravel frequently. Uses A/C extension cord for electric start. Snow removal part might have been year 6. He isn't too used to snow otherwise he would have cleared it off of the cars before clearing the drive of snow. ;) Thanks for the video - I am considering buying one of these.

Would love to get the template for the handle if you are still doing that. Thanks!

I like how you painted the engine to match. I’m doing the same exact thing repowering my troybilt.

Where can you get one

Nice to see a video of one actually plowing with a blade. Finally thanks for sharing

Which way do the tines rotate?

How did you get the tine carriers off?

How did you get the time carriers of ?

I have the same old Troy built tiller but mine has like a two piece looking cast wheels. Runs excellent, Kohler 7hp power.

I have a '98 Craftsman GT. A big heavy powerful machine. Way better than the newer riders I've had. Keeping this one for the long run.

That’s a easy fix. A little sanding and painting a new engine and tires. And your good for another 30 or so years.

I just bought a 1980 troy bilt horse. Pretty cool machines don’t build them like that anymore.

You're just too cute I was doing this 15 years ago

Whiskey tango foxtrot!! Remove the cutting deck?? Kids today those try anything!!

How menu quarts of gear oil dose it hold

Valve lash?

My Dad had a David Bradley that had a sickle mower, harrow and plow attachment, nifty, later he got a troy bilt that I use today. He passed in 2021.

Je veux savoir si vous commercialisez les outils 'agriculture

I have two horses and I'm curious if you know any trick on the engagement pins the engine moves up and down on. I had trouble on both tiller getting the pins freed up as they were rusted up to being frozen. I am curious if they should be highly polished or even chromed.

A very comprehensive look at the differences in older & newer frames and feature's. I just finished tearing down my 2nd DB today(917.595 2) with the one piece tube frame.I am looking for the clutch disc if you know a source. I am really enjoying the pursuit. Thx for the upload. You have a nice collection.

You have two traketor mini,brother have moeny for buy traketor

Wood for the reverse what a great idea..Do you have a video on that?? Love these old machines.

......I'm compulsive in all things.....I have four Horses I am working on them right now. February 1 2022.....I can't buy just one of anything...I keep finding more and buying more....

Nice

Nice, I bought a used tractor like this.

My top of the cap want go down its for the filter how do you fix it?

Dumb question: if you don’t want to weed by tilling can you attach a planet jr toolbar to the Troy Bilt and weed at one pass?

I have similar one, not bad for around the house

how long did this take you?

Nice Oldsmobile Intrigue, still have it? Do you think the plow will work on a Craftsman T110 mower?

Lovely informative record of a very nice renovation. Well done

I just love these summertime snowblower reviews. can't wait for the wintertime lawn mower reviews!