Відео

i'm jealous. my sandy soil would never allow such nice vertical walls. it would collapse in on me constantly until my walls were sloped at least 20 degrees off vertical

Have you had any problems with the AC compressor because you did not replace the coil?

Doing this this weekend. Do you think I could use concrete deck blocks as the base?

Great video and explanation, then a sweet cheap solution. One question… where do you find the button part? I looked online but couldn’t find it.

Thank you for your detailed video! My Grohe faucet is 19 years old and around the 10 year mark, the spray head had the same problem. Back then, I ended up buying a new spray head. This time around, i decided to search for a solution on YT University. Your video explains the "reason" for the fault and your fix is brilliant. I thought I would add some insight that might help others, as I have the soft black model and I could not remove the switch. It seems the cover to the switch is a "one-piece" unit. Thus, I could not punch out the internals. However, I was able to use a small dull edged flat head screwdriver to remove the white o-ring and replace it with a new o-ring, without having to remove the internal parts. Super easy fix!! Another commenter mentioned lifetime warranty. Yes, there is that option as well...... to the original owner with a copy of the receipt. I believe I might have the receipt and will try to get a warranty replacement as well. :-)

How to fix leak from bottom The machine is prone to leaking from the bottom due to it's design. If that happens, you need to change the seal under the boiler chamber and you need to deassemble the whole machine to get access. It's a tedious job for the DIY repair person, but feasible. You need to get Krups MS5015004 Esprosso Machine Boiler Gasket Seal by KRUPS available on Amazon for about $25. I repaired mine and works like new.

I will be hand-digging a 1'x3'8"x4 hole for exterior stair footing. Your video was most helpful. Thank you.

well, like a handful of others, this is pretty much exactly what I was looking for. My windows didn't have the wire assist engaged, but the assembly/disassembly was pretty much the same. Intricate and overly complex, but there are at least two windows in my house with it and I am definitely better off for having found this video!

Great video !

Followed the exact steps and worked like a charm. No $149 but $2

you're THE man

just need to replace the o-rings. cost a couple bucks

Where can I get one of those counters? Do you have a model make manufacture? I have a few but would like that one also.

Hi. Great video. I have a slightly different problem with the same model. Mine has started to leak coffee underneath the machine. So it operates as normal but have to keep wiping underneath the machine. Trying to determine where it is leaking from.

Nice job

Fixed my faucet, thank you for saving me a bunch of money 😊

Respect! Are you just a bonkers good DIY'er, or is there some kind of mechanical DNA going on here? 😁 Thanks. P.S. I got a set of headlight housings for my 1999 for about $120. I laugh at how much better that makes it look.

That concretes junk. Way wrong. Over kill on the piers unless u live way north

Good job. I did nine of them for a shed base in a slope. Used the same wood left over from the old shed. Level all of them. Use a wheelbarrow and my old military shovel to mix all 34 bags. Never lift a bag, Roll the bags from ny minivan to the wheelbarrow. Took me three half days.

Спасибо за видео. Похоже у моей кофемашины такая же проблема. Срочно закажу деталь и надеюсь вскоре моя машина заработает.

Oh, my LORD... You have no idea how much you have helped me. This is exactly 💯 what I've been searching the internet for. I can almost cry finding your video. I have broken the string on 2 of those window sashes trying to put the window on the track. Now I can't find them anywhere online to replace them. Those sashes have no item number on them, so I dont even know where to start looking for them 🤬. But at least now I know how to proceed on installing the other windows. Again, THANK YOU A MILLION TIMES OVER TOM. ❤

Great video. Thanks for the tips to make certain things easier and going into great detail price for parts and all thanks

Great video. Very helpful.

Tom, thanks for the great video. My Krups is leaking water; every time I use it there is water underneath, any idea of what could be causing it?

Absolutely disgusting how long this takes. Shame on you, Honda

I’m in the process of making this now with 4 sheets of 3/4” 4x 8 plywood. Do you or anyone have any tips or changes you would make? I plan on putting wheels on mine and it will be outside all the time in S. Fl weather. I’m also thinking about putting hinges on it in case I need to break it down.

I have a EA815 Krups that is leaking coffee exactly as you said. Would the repair be just as easy?

Thanks for this great video. It helped me to fix my Krups ea81070 without any issue!

Hi there. Any idea why my Krups ea80 sometimes suddenly grinds just like three seconds, then starts making coffee?? Then after dozen of coffees grinds a bit longer, then starts to finally grind normaly about 10 seconds or so.. thanks for thoughts.

Great video with good tips. Very concise.

How do I buy the rubber switch cover?

Great video. Thanks for the tips to make certain things easier and going into great detail price for parts and all thanks

Thank you

Hello, I want to ask, I have a Krups EA829010 and when it turns on the display shows insert the cleaning drawer, but I don't have one for coffee machines, they are on old types. The switch for removing deposits is ok. How to turn it off. Thank you for your response.

OMG you are a genius. Worked like a charm!!!! Thank you!!!!

It runs on the oil pan I'm sorry sir

Hi sir I'm Vernon I bought a 2001 Honda Odyssey van 167;000 miles but it has a oil leak it's oily behind the balancer it runs out the oil pan when you took off the oil pump and you showed a gasket that you said it leaks from sir where does oil leak out from when that gasket leaks please ty Vernon

Thanks for the video. It really helped me get it all apart. You made snapping in that white lever look way easier than it actually was to get out and put back. I could not find an O-ring the exact size you mentioned so mine were a little smaller. Problem was, it would run a good stream until I pushed the spray lever then it would never go back. This is because the O-ring kept sliding back off from too much tension. So I found much easier solution. I found the faucet head on the Grohe web site, told them my issue and they are sending me a FREE replacement head. 😋😋 Another option, I saw several sites selling the bronze and some other colored versions cheap for $5. So all you would have to do is pop your insides out of the shell and replace w the new ones from the ugly colored $35 shell.

Yeah so I have two homes completely outfitted with Grohe ythroughout and they consider a "Lifetime Warranty" to be ten years. She was quick to pooint out that it is not the "lifetime" of the home owner? WTH I guess I have outlived the Grohe statute of limitations. I even polietely argued with them on the phone and they pushed back, outside the ten year period a "manager" has to approve it. So now I am on the fence with recommending their products to anyone, especially my friends in the building trades. And I have a new home with three bathrooms that need remodeling. Oh well.. as with all good companies they are not seeing the big picture of brand awareness.

When you clean it more often this problem will not be there

This gentleman did an excellent job explaining how to repair the faucet head; one of the best instructional video I've watched, thanks.

I got the new faucet and it comes with 2 little cartridges I have to choose one plus a Teeny little trumpet shaped clear plastic thing which I don’t know where that goes. I’m Sure it’s simple but don’t what to screw it up. I didn’t see you install either but you said you had a new faucet? That one looked older inside the mechanisms.

You put the grease on the rubbers, that is going to come in your coffee?

Great video. Saved my life

Most pros don’t show the fight and aren’t honest in how much time it took. I used to be a professional motorcycle mechanic. Tom shows the real fights some auto repairs present. This one is a tough repair in all but the Honda shop with specific tools to do the work.

Hi Tom, are you familiar with the Distributor on these Krups Coffee Makers … I was told mine may be clogged and it’s causing the piston to push up and leak coffee from the top of the piston area and/or during the cleaning cycle It drips coffee all over the counter from the bottom of the machine. I did change the O-Rings on the piston and the Gasket/Seal at the bottom of the piston assembly but it still leaks. I also purchased a entire new Piston with O-Rings but I have not changed them yet I greatly appreciate any insight or suggestions you can provide Thanks Jim

Great video. Now I know how to clean my Grohe sprayer head. One note, Grohe has a lifetime guaranty on their faucets. They have sent me 4 replacement sprayer heads that have the longer toggle switch that you don't have to hold down to have the sprayer setting. Originally, I didn't find my receipt but they sent me the part anyway since they are the only Grohe manufacturer. I eventually found the receipt and I sent them a copy for future replacements. Thanks again for the video. It's very helpful. It's puzzling why Grohe doesn't provide a video like. yours.

I can’t find a video for making the forms? Please send the link. Thank you

I replaced the piston but still have leakage around the seal. The piston drifts up during the brew cycle exposing the top o-ring and coffee and steam blow through. Any thoughts on why the piston does not stay down sufficiently?

Hi Tom, I also have a Krups EA8250 I replaced the piston O-Rings and the center gasket after taking nearly the entire machine apart. I did not replace the piston yet since I thought it would only need the O-Rings What suggestions do you have Thanks Jim