Відео

I have Toyota land cruiser 1994 and turns off when steering right any ideas

Can you reuse the gasket on these diff?

I dread the day for my 9N. I have one bald rear tire and who knows the last time these have been off! Great Video!

Where did you get the brake shoes? I have a 2ton chevy,i been looking everywhere for brakes without luck

Dana 70 or 80?

I tried to tune my 5BTV today with no luck. Its not even within the bands for 10,15 and 20 meters. According to the VNA its too long. I tried calling the company but they were closed when I called them. Its really frustrating.

Uhhh… could I have those spin balanced Please?? 🤣

Nice thx I’m doing rn for my dc5

at 6:34 you're trying to put that o-ring or seal or whatever it is on the release valve, I've got one of those in my kit too, did you ever find a use for it? I put one o-ring at the bottom of the main cylinder but the one you're holding looks like it goes with a different model or something?

I can smell it! 😮

Dear Sir- thanks for this video. Quick question: have you started selling your radial adapter plate? I’d be VERY interested. After 2 years, are you having good results? Any problems? Thanks, KQ4IXD

Great thanks, and the hole diameter?

Great Job, I am getting the 6 BTV next month and I am wondering how to prepare the hole? How deep and what circumference diameter to fill with cement and what type of mast in length and diameter to fix in the ground and size to remain out for holding the 6BTV? Can you help please?

I think i would have made like 3 of them...that way if the knuckle breaks or whatever i dont have to wait for another one to be made

Great runner, i want to buy a 4 door sedan monterey that i found on facebook, not as cool as your 2 door hardtop, but still a great car

whtas the power on 220 mhz??

Sorry but that looks like a shamble of a set up 🤣🤣🤣🤣 73 s

On a Cummins recommendation to change how many miles in between?

Olá amigo, jáh troquei 3 vezes os dois retentores e o óleo continua vazando. O ano da minha dodge ram 2500 é 2005. Eu li em foruns para não encher demais de óleo que vaza. Acho que deve ser isso. Acho que meu mecânico enche de óleo até vazar pelo oficío, no entanto li que nos diferenciais dianteiros das dodge ram ano 1994, tem que deixar 1 polegada abaixo da parte inferior do orifício. Você sabe tecnicamente qual o nível máximo, exato e correto, limite de óleo que nao deve passar?

I think I would do some reading up on that engine before starting it dry without oil or grease .. and no coolant .... research first ....

great job 73 from kb2uew

First song groovin

You should have done all that work to a Dana 60

do yall sell this exact kit?

Dan, can you please tell me what part name for the galvanized hanger bracket & where you got it please, thanks. How’s setup working for you so far?

I am the proud new owner of a '50 Merc, my first flat head! I discovered I have a broken valve and also adjustable lifters. What is the valve removal procedure? Pry the valve spring up to release the "keepers"? Thanks in advance. BTW, love your '53!

Idk why, but the first half of the sound track made me want to fast forward to all the good parts and the end. I fought some other urges too, but I did make me a sandwich afterwards.😂 Seriously though, good vid and work. Looking into doing this to my K5.

Those tie rods/tie rod ends Look GOOD Sir!!

I had the same problem with my X50 after about 8 months in service. My ID-5100A went deaf. I measured 2m SWR over 4:1. I took it down and opened it up. It was full of water! All the foam rings were soaked and the copper element was corroded. Maybe you should check yours as well. I have no idea how the water got in but since the top of the element was wet, it must have got in under the chrome cap.

heat the plug? no. heat metal around plug. expand.

Love the video. Filming while working on top of the roof deserves extra points!!

Dan...does this make the Bao Feng work better and go farther? :-)

Lets Go Brandon

Good stuff Danimal!

Thanks for sharing Dan. Would love to see more videos in 2024.

As a guy that just had to take a steering arm off and deal with those conical washers I think I speak for all of us when I say screw you for not putting anti seize on any of that stuff. 😂

If using a blade, get an “Exacto Knife.” Way more control over a razor blade. Or use teeny tiny micro clippers to “crush” the center. I would keep off either end. (the delicate solder pads.) 💁🏻‍♀️

Since you've had them longer than just about anyone I can find, have you had any issues? I just haven't pulled the trigger on Amazon fuel injectors. I made the mistake of just replacing the seals on mine when the headgasket was done, but now I've got lean codes occasionally and a rough idle when I pull up at a stoplight in gear especially. If I can fix that then I'm ready to go wheeling. Also need to change the injector plugs when I remove the injectors since almost all of them have broken tabs. Just don't want to wait the turn around time for mine to be sent off, and wondering if these are going to last.

What good did the music do in the background, other than mute and muffler your voice.

of course when the video first started i said to myself ....this gonna be a long day

How did you power this if you ended up making it mobile?

I like the music choice. Thank you for sharing- I just bought a 3800 '48 and am getting familiar with the model. Love these trucks- love the stovebolt engines. Wonderful machines. :) Cheers!

to much technology back in the 50s lol oh in the 40s

Looks like a difficult job ,How much would this likely cost in a shop. ? I’d imagine 1500 aud

they aren't really an upgrade. glass ones have the ability to use very fast acting HRC ceramic. these are the exact things you want on sensitive electronics because of their ability to prevent arching after blow. those car fuses don't have that extra security and you may still arc and blow ur equipment even after the fuse blows. this is why you can find really expensive ceramics ($100+) but you cant for the blades

what is your new mpg after changing them?

How does it hold up in wind. Im in Southern California and have to deal with our Santa Ana winds but Im looking to do something like this.

Thanks for posting. You guys are pretty great. I’ll be trying the course tomorrow.

Yeah... i just have a mill laying around 👉👌🖕💩

Im trying to save a chopped mercury. It was chopped without being braced and the doors are almost pinned shut. Do you have any advice? Thank you