Відео

Okay dear 👍, thank you for your interest.

Thank you for your support dear 🌹👍

@@johnnyvenu6893 you are welcome🌹

@@basselonabi1472قرررربيت

@@inbatamilan1567 Hello Dear, and thank you for your question. To achieve travel times of > 1.5 s in small actuators, the air rate can be reduced with the restrictors Y1 and Y2 . By turning clockwise the air rate is reduced up to shutting off. To set the restrictors it is advisable to close them and then open them slowly (see initialization RUN3).

🙏

Kindly specify what exactly do you want to be clarified

@@narasimmansairam7154 Hello dear, thank you for your question. H2 is the distance from the transmitter to the lower point of the tank, as the tranmitter is installed under the tank (500mm), so when the tank is empty we still have the pressure effect of the liquid inside the pipe (impulse line). Otherwise we need to seprese this value inside the transmitter itself. to get this point very well, i recommend to watch the following tutorial video: ua-cam.com/video/cQg5cU8hRbA/v-deo.htmlsi=cRxW9cjanbdRhbXN

Got it ,Thanks a lot

🌹😘

🌹

@@diaatakhin5777 تحياتي استاذ ضياء

@@minhquantang3214Hello Dear and thank you so much for you comment. if i got you well, there is no need to do it, as i mad an assumption of the static pressure in this example. anyway i be will glad if you clarify more (in witch prat ), so i may get your point better 🙏

@@jitubabusay2826 Hello Dear, one of the solutions is to make scalling (in the plc ) of the analog output. by the way sipart ps2 has split range function, you can adjust parameters YA and YE , for example: set YA= 10 % and YE= 80%, that means valve will open from 10% to 80% (4mA at 10% to 20mA at 80 %)

@@Set-Pointcomming 19 ma when giving 100% command that's problem!!! Want to open 100% in 19ma command, What to do???

@@jitubabusay2826 yes we have a problem, please chek the compatibility between the confeguration output of the controller (4-20mA) and the input on the postioner (4-20mA). otherwise you have to do a reconfiguration. if its not work, you may send me a video of this issue to : setpoint.la@gmail.com

❤ شكرا استاذ ضياء

You are more than welcome 🙏

Please review this tutorial video, and let me know if you need any additional information: ua-cam.com/video/kesmgta2jHg/v-deo.htmlsi=TS01GEG7d9vdoxVq

You are more than welcome dear🙏, In such cases we used multivariable flow transmitter or a flow computer connected to p,dp, and t transmitter. here you may have an overview of this type of instrument: ua-cam.com/video/1zGav6j3x0U/v-deo.htmlsi=ZwSLXc844V1bJ0T4

If you require and special information please fell free to let me know.

You are more than welcome 🌹

🌹🌹

🌹🌹❤

Thank you so much for your interests, i will prepare one and post it in the close futere.

Thank you 🙏

🙏

thank you so much for your support 🙏

Thank you dear for your question and interest, I will prepare a tutorial video of this point and send you the link a.s.a.p.

Dear Friend, as promised please refer to the new tutorial video of pressure drop calculation, hope you like it: ua-cam.com/video/DYkptBvdpCg/v-deo.html

🙏

🙏🙏

شكرا 🌹🌹

🙏

h min is minimum water level allowed ( measured or started from the bottom tap of the drum)

Glad you liked it

Hello Dear, do you mean that you want a tutorial video of ABB mag flow meter calibration and parameters setting?