Відео

why no more speed3 videos ??

What size is t fitting for oil pressure sensor?

Good video💪💪💪

Please lose the music for future videos.

The tire must be off to do this?

How did it last 5 years later? I wanna do this

I just replaced the pump.. previous owner used some off brand Asian fluid… the O rings were fine (but I still replaced them) but it fixed the problem. But your noise wasn’t nearly as bad as mine.

Can you tell me where the sensor is located in a VW CC 2010

Life saver!!

You really don't need to gap them?

Hello, I have two questions first one is your transmission a cvt and second does the sensor differ on lhd or rhd?. Thanks in advance

Did you gap the rings for boost?

This isn’t your problem or your fault at all but for the life of me I’m trying to find this same exact part but on a 2007 A6 and nothing will pop up in the internet at all just your video and one other. Do you personally happen to know where it might be on my make and model or maybe have a link handy for that specific car because every other video like yours just isn’t in the same spot for me

Wait so you used all even rods and pistons?

Good thank yout

What did you do about the wiring for the engine since the 2.5L come with a different wiring for the engine that the 2.3L has?

Best video concerning this seal replacement... so hard

I didn't see any sealant applyed at the rear and the front of the camshafts cornering (engine head)😮

Service bolt on the exhaust cam FIRST!

Fckkkkk a spider hell no im out this video

How much did they charge you for cleaning ???

You are best! 😊now i need to see where is located my sensor on my audi 2.4 v6 petrol from 2005!

Funky yea,you the man ,you still alive

Every one already said it :the music sucks.

Parts numbers plzzzzz

Hi does the 2003 Audi A4 b6 3.0L Qauttro also use this sensor?

Is the same for the code P07B600?

Mines makes a funny noise almost like a suction noise it’s not like the one you demonstrate it’s more like a doont dooont dooont it only does it at acceleration from the stop any idea what that is and the break sometimes kinks up

Hard to understand your video 😢

What kind of silicone do I use

Nice work

Will 2012 work

is there any way to move the rear wheel back or forward? i need to move mine back closer to the rear of the car to be more centered. it’s too close to the fender on the rear door

I have this code on an 04 Audi A4 V6 but I’m experiencing inability to shift gears while in motion sometimes being stuck in 2nd or 4th even from a stop. Would this still help?

Ridiculous question, but can you swap a speed engine into an automatic Mazda? Gen 1 or gen2 ?

Chopping hard as hell hahaha

I'm building a 2.3 in my 1g dsm 7 bolt. Good tip

Can I use a 2009 hybrid 2.5 Ford fusion bottom end or no?

Thank you for this. Made my life so easy, just swapped out both sides. With your video on repeat with headphones , lol

Where is the PRND switch in the 1.8 CRV tranny??anybody know?

Why are these people saying that they're drilling and tapping? They're just drilling, there's no tapping involved. I want to see a video on drilling and tapping a oil pan Not just drilling and put it on screw Screw together bungs

Seems I'm late to the part, so the block is a closed deck on the 2.5 ? Of did u use the 2.3 block ? I'm wanting to build a swap for my RX7

Esta bien poner las bielas así?

Music? For what

Do you still have the car? If so hows it holding up?

There should be a place for an Allen key in the bottom of the bolt to keep the ball joint from spinning. Then, just use a wrench to tighten the nut.

Dude your a life saver! I did a suspension overhaul with all Megan racing and I was way off

Is it possible to putbthe 2.3 heads on a 2.5 from a 2018 mazda 3 gt? Ive been researching but cant find much info.

So i can take my 2.5l na on a 2018 mazda 3 grand touring and put a 2.3 head on it and ill be ready for boost?

Is there a follow up video??