Відео

Thank you for this video, i think I made the window "out of axis" by adding air deflector the glass had too much pressure and went out of its rail, I tried to plug back in on the two metallic rails but when I lift up the window we see that the glass doesn't go straight upwards but tend to go forward into the exterior rear-view mirror, I think if I try to continue to lift the window it would just explode by pressure lol ! What I noticed is that a black magnet with a small rail guidance fall but I don't know where it should be pluggued ( i think on the front part but it's nearly impossible to reach..) and when the window lift up the joint is quite pushed by the window i'm not sure how to handle this without breaking completly the glass, thanks ! my guess would be to try to have the glass on the two vertical rails but i only succeed in putting on the one near to the outside but not the one near the mirror

How did this work out powerwise. Better or worse.? Have my b28 apart and thinking of giving it a small port and poliah

I’m thinking of replacing my Kenda kr20 for these

Your a beast bro 👍🏼💪🏼

Thank you very much for sharing your knowledge. I have got the same bmw compact exactly like yours and in still blue color. I have booked it in for repair on Tuesday 23 April. I have experienced the window problem 4 to 5 times and decided not to use the power window and I got out of the car every time I entered the car park. Even though I stopped using the power window it still happened i.e the window glass did not go up after I used the power. My luck was running out! Your video is helpful for me and liberating.

What bumper is this bro?

Tried this. Seller forgot to post me the correct silicone, instructions weren't great, I put too much silicone and now can't press the button. WIsh I found this video first, i would have rather had the button be loose VS stuck. What a Nightmare.

basically you want to stay away from the floor of the port, most of the power is made in the bowls under the head of the valve, the sharp lips you want to remove, you want to create a higher CFM rate, the way to do that is to create a natrual velocity stack of 1.5 degrees of taper you want to raise the roof of the exhaust port by 20-30 thousanths , you want to knife edge the center of the exhaust divider , and make an airplane wing on the intake side of the exhaust , stay away from the floor if you remove that natural curveature youre going to create deadspace and loose power you dont want to increase the diameter you want to change the shape to 1.5 degrees of taper

Do you need lips that specifically fit the equips or are they like universal? What type do i need?

nice dude 2 questions. whats the name of the tool that can bend the pipe and how do you know if you will be able to mount a bumper over this. I'm thinking about doing the front bash bar

boa of waoa

👍👍👍great video!

Motion sensor button be a better idea, like Airport toilets

excellent video lad

Rip weep

tuff 🔥🔥

Pls bring these back

yahoooooo

Well happy your back on YT Ben <3

Tempted to buy some of these for for focus ST as an alternative to my PS4’s as for some reason I keep getting nails and screws by the tire wall and it’s not cheap at £200 a pop 🙄 sick of having to replace expensive tires… would you recommend just for normal b lane bashing for good grip ?

Rip Weep

Love a bit of DnB little Kev

what size tires are you running in the front?

Best video for glass replacement, mirror replacement, and cover replacement - all in one. Thank you.

Nice video always enjoy watching them

Nice, I just purchased some Accelera phis for my 2006 Mazda 3 for only 55 dollars each. I'm located in The States. Usually I purchase continentals, Michellins or other higher end tires, but since I'm back in school, I decided to purchase these budget tires. I still need to get them installed. I just hope my tire mechanic knows how to drive a standard, since automatics are the majority here. LOL

So what you just crank the engine till it’s tdc then everything ended up perfect what if one is off

Hey mate, just come across the 651 Sport Xtra, and was looking for info and found your channel! I'm looking for some semi's for my 125i for my 2nd set of wheels (for summer use). Running PS4/PS5 on my daily wheels. I've not considered Accelera before, TBH I thought they were ditch finders. Would you still recommend them now (2 years later)? I can get a full set for £348! 🤯 Ran Nankang NS2R in the past but they are so noisy. Cheers!

This is the video ever

Fire

Mine literally popped all the way out 🥲

Wreakin’ the lanezzz. B road bashing is UK touge. They don’t have tractors coming the other way in Japan.

It’s sad that there isn’t much UK streeto online. Filth love watching yt for easy nicks. Fuck um, just keep it live and remember to all split up when you scarper. They can pull you all but someone will have to take one for the team.

I'm experiencing a similar issue with the studs. Vehicle had a headjob by a dodgy mechanic a year back and now I'm trying to reinstall the vanos. I wanted to visually check the slot in intake for travel. Two of the nuts seems to unwind the stud! Not sure what to do at this stage. Problem being it will no longer completely tighten up and keeps spinning.

Everything is easy, please show us how you PUSHED the corrugated plastic tube in. Thanks.

Actually saved me from a life of crime, thank you for this remix.

How did the mounts feel way there any vibrations just fitted polys on mine and there terrible looking to get these now 👍

I ran these spacers for ages and never snapped a shaft 👌🏼 only took them off as I’m going to be using different shafts now

Yes ld

Cheers bud!,

I would recomend replace the crankshaft position sensor if never replaced before, and if the odometer reading is 150+ K miles. An extra $125 will save a lot of work since the intake manifold is being removed.

Can I daily in these?

Thank you sir

Where is the rear jacking point from ?

Ty for video

Hey bro, I noticed the starter you pulled out is a pre-1996 which has thin ears, is threadless and requires a bracket, and you replaced it with a post-1996 starter with thick ears, has threads and doesn't require a braket to be mounted, did you have any ensuing problems with that? cheers

Mate can I ask does the oil filter housing have water pass through it for cooling the oil

nice content mate nice to watch some normal man working not a fucking idiots

Just stick it in the trunk, my guy.

Is the location of the fuel pump different for left hand drive?