Відео

Funny Observation: Mr Heater warns NOT to have an external tank in the same room as the heater lest the tank leak & kill everyone in the room AND/OR the heater light off the gas with its burner & burn everyone to death. Gotcha. HOWEVER, My little buddy heater has a pocket in the side to put a 1lb bottle just INCHES from the flame. What? 1lb bottles never leak? I think not. !

Hate these heaters. They never work when I need them. Going to try one of those Amazon jobs that just hook right up to the tank. No hoses or any of that BS.

My 690 was pretty new, but over winter crankcase filled up with two gallons of gas, didn't figure it out because couldn't really see the clear gas when checked oil dipstick, anyways, after trying to start it a while, then noticing that, I had blown a ton of black oil into exhaust, shooting/dripping out, smoking. Changed oil, gas, plugs, gas filter, carb, couldn't ever get it to run again, almost, but..... compression test I just did shows 130 psi right side (dipstick side), and 75 psi left side. So I think that's what your motor is like, the same side as mine is the low compression side. I don't know if I can figure to tear down and rebuild or save for new engine, or call a shop for a quote for ring job. Oh ya, when I poured a couple tablespoons of oil in spark plug hole and tried compression test, it went from 75 to 125 psi, that's why I think it's the rings. Haven't removed valve cover or anything. Thanks for vid, nice garage/shop!

I just use their recommended "oil-free" hose & 2 winters it's worked every time, every day hooked to a 20# tank. I use the BIG Buddy with 2 ceramic heating elements. 18,000 btu on the high setting.

Thanks for the detail. I have a 45 horse LS with error codes leading to the DPF garbage. What is interesting is all the fuel it takes to perform a regen and all the smoke and trash that comes out of the exhaust. How is that "environmentally friendly" (Idiots!). Another money grab from big industry to pacify the environmentalist groups.

G'Day, You've just given me a great starting point as I had the same question: can you use other devices using the My Plasm electronics, greta job!

Used the filter and it still kept going out!

Flush those lines out with some brake cleaner or alcohol or something other than air. My heater was absolutely full of oil

That's called a manual reset.

For future use away have your MRI buddy heater 1 foot above the tank , but it's oil residue.

I dont know if im seeing this right or not, but is there a regulator on that big tank line?

The more flexible the hose, the more oil it contains. The oil leeches out when the hose is pressurized.

i have issues even with the filter-

When im done using my buddy's i put them back in a plastic bag while storing them away, haven't had any issues! I also have other sources of heat production incase the power goes out! Prep like your life depends on it! Wemight be in for a wild winter!!!!

YES ... IM ON MY 2ND BUDDY. READY FOR A THIRD. I HAVE TO BLOW MINE OUT EVERY COUPLE RELIGHTS. JUST KEEP GOING OUT. WITH THE GOOD BLUE FLAME, i only used it on the 4.4gallons tanks. if it dont work i use a brass brush clean the whole area, then blow it out with a small air compressor blower. and it works. i seen someone pulled the hose off red button depressed and blow it out backwards. have not tried that yet. im not mobile so it difficult for me to get that far into it. (Knee replacement)

Ive heard its oil / substance in the LONGER lines.

So did you run it and leave it overnight or run it and leave it over the summer???? Which was it???

Vato thank you good INTEL

Over the last 2 years I've run over 2 dozen 20# tanks through my Mr Buddy, and tonight it started acting up and finally required a cleanout of the lines. I do use the inline filter. Might be time to replace that too.

Wow what a job. Keep up the great work. I've been running plastic on one of my shed builds, instead of walls.

I hear that if you use a big tank with a hose, you need to use a filter between the heater and the hose.

Absolutely no reason this device should cost $2,000. Should cost no more than $300. It's pretty simple.

What happened to the new plasma table build

I’m completely for leaving a better world for my grandchildren but some of this stuff is unnecessarily inconvenient for the small number of people who don’t use these engines professionally. I average 50 hours a year on my tractor and believe that there should be an exemption for this amount of use. Currently I have a pre-emission year tractor and one that was deleted before I purchased it. I have more guilt about my gas powered lawn tractor, log splitter and chainsaws.

Hopefully Benelli took care of you on the warranty end man. That’s really frustrating.

I have never understood why Benelli went with a carbon fiber rib. Dumbest thing they could have done. At least it’s warrantied. If I’m not mistaken the 20 gauge has a metal rib.

Thank you,❤ I've had the same problem for so long

Its the oil coming out of the hose

I've tried using a filter with a brand new mr buddy and it won't light.

The 4DPF site and ordering process seems super scammy. Other than your experience did you find any info anywhere about them?

You can now also buy a refillable Fuel Keg and refill kit and avoid any host problems at all.

Bought my big buddy heater for around 200$ plus a 50$ gas line to hook up a bottle...never had so much trouble with any heater I ever used. .DONT BUY A BIG BUDDY HEATER...mine still don't work and it's practically brand new!!

Im off grid for over a decade. Use Buddy everyday in the winter. I use a 30# just clean your buddy once a week. Yeah. Clean your shit. Trust me. Clean the pilot with Alcohol and Pipe cleaners. Im offf grid. The dust, dirt and crap gets into it. Maintenance.

Do you know if the egr still occurs with this kit to burn exhaust gases or do you unhook that part of sensors when you install the kit

Love your cnc videos. You got a new subscriber. Thanks for all the info.

I have a guy saying you have to send the computer off to get it deprogrammed? Any info on that?

They make a filter to put on you heater when you run a 20lb tank ,i think i got mine at home depot

Have you got the parts list yet? Like your build wanting to do something similar

I just subscribed. Great video. Neighbor got a kit for an L3901 to put on it.

That's exactly what happened to mine last year, I will definitely pop it apart soon and clean it up

Yeah… he definitely busted that rib on something moving the gun around.

Did you try to put the screw through the other side?

He’s knocked that rib on something and broke it.

What light are you using

I have shot benelli every since the original super black eagle and have loved them the only one I have had issue with is the Vinci I currently shoot the sbe3 in 12 and 20 gauge and I am rough with them and have had no issues

du bescherst dich das das www 0 infos hat baer selber mast du das auch schreube auf und zeige genau wo die kabel hin komen alss ander mach 0 sin

Hey, Good lookin' out, I appreciate the heads up on how to avoid destroying my new/old outboard. I would have likely done it all wrong.

I used mine for yrs with a big bottle never had a problem

Hello, my name is Jonathan and I have an esab 205 I bought a used, but it feels like it has a sick problem. I use a millers.

Outstanding presentation and topic ! I like the way you talk!