Відео

Hi, I have one of these modules configured for 3S and I have a 18V 2.5amp switching power supply. I have some problems when trying to charge with this power supply. Thank you very much. 💪

hello. i bought a similar BMS circuit using 4 lifepo4 cells to make a battery for my motorbike, but it has a problem that the led and lcd screen will be flicker like unstable voltage. I don't know how to describe it but if I connect a led buld into battery, the light will be very bright and stable, but when I install the battery in the motorbike, the led bulb on the motorbike will flicker a little, the screen brightness is flickering aswell. can you help please

สามารถทำให้เปิดค้างได้หรือไม่

මේක චාජ් කරන ගමන් ඩිස්චාර්ජ් කරන ක්‍රමයකුත් එකතුකරන විදිහ පැහැදි කරන්න පුලුවන්ද

Excellent demonstration. By the way, how to make overcurrent/short circuit protection for this module? at least taking a signal from the ic to operate an indicator led or buzzer to know there is a short circuit or overcurrent.

Would It be possible to Bridge the soldering points using an HB pencil to make a Bridge bettween eachother instead of soldering

TP4056 module eken input output dekama ekama port eken ganna hadaganna berida.

Bro this Module will Charge My lithium Ion cells i connect 30 Parallel my Battery 2000mah per Battery can This Module Will Charge My All Parallel battery ????

As shown, if we want to connect this 4.2v battery with 6v 3A 3W solar panel then

Module 2k parallel karala battery 4k charge kala hakida sir.

it's not working on iphones, complete input and output but charge not increasing.

Please tell me, what program did you draw the diagram with?

Good explanation

Thx for the video. What does the flickering LEDs indicate?

Great explain with clear voice 👍I have 500mah li po battery but table not mentioned resister value for 500mah can you help?

44v 14a 555w solar penal ekakata sapot karannethiweida

Can i connect charge led indication sepparately ?

455w 44v 14a solar panle ekak sopot karannethiweida

455w 44v 14a solar panel ekak denda beriweida

Thanks you so much

English title... I was hoping for a review :(

Bacon

Could not understand a single word but the pictures did help a lot. Thank you so much!

Olá jovem, eu comprei uma plaquinha destas para usar nas minhas 04 células de lifepo4, até agora, nunca acenderam um led. Sem dúvida, esta é a melhor explicação sobre esta bms, no youtube. Obrigado.

I am powering a device with low power, so the converter shuts off automatically. Is there a way to stop this behavior?

posso usar essa bms em celulas 26650?

යාළුවා මට ඔයාව සම්බන්ධ කරගන්න පුළුවන් විදියක් කියන්න ඔයාගේ නම්බර් එකක් වුණත් කමක් නෑ දෙන්න පුලුවන්නම්

That's a great video. I tried to change my 5s bms to 4s. But I don't have 0ohm resister. Then, Is it okay to solder Directly without 0 ohm resister?

10000mah da puluwan meken uparima

what will happen if i connect charger in wrong direction? is there securty for that or i losed the bms

meke output eka 12v witharada ? 3.7 solar light ekak sambanda karanda barida ?

Gracias x la explicación del interruptor pensaba que me estafaron al comprar..miles de gracias..

Bro this module restarting automatically. Why this is happening. My router almost dead for this

Hello, I was looking for information on what those LED lights mean. As I understood - LED lights enabled when balancing for that cell is happening. Somewhere near the end of charging. It is indicator that balancing for this cell is happening (additional current flows over that balancing cable)

Всём доброго дня , ребята вопрос такой , смонтировал bms 3S 100A на пакет 18650 , пакет заряжен 12.4 , а на выходе 10В , на выходах балансировок почти ничего нет , проверил другие 2 платы , такой же эффект , что с ними не так ? (До этого собрал 4 пакета , всё работает) , заранее спасибо !!!

TP5100 මොඩියුල් එක ගැනත් පැහැදිලි කිරිමක් කරන්න පුලුවන් ද ඔබතුමා ට

ගොඩක් වටිනවා .පොඩි දෙයක් අහන්න ඕන. ඕකේ අවුට් එක mt3608 හෝ xl6009 වගේ බූස්ට් කන්වටර් භාවිතා කරන්න පුලුවන් ද රිචාර්ජබල් ලයිට් හදන්න ?

what resistance ntc did you use?

1.2 v betty 4 k 4.8v charging karanne kohomada

very good. keep up.

This video explains something very different then the other TP4056 related videos. Great job.

EL DEL 21 V SOLO LLEGA A 16.3 PROBE CON VARIOS.

4:36 не работает 4.35, в обоих вариантах 4.2 макс

5s එකට වාෙට් කියක් ඉන්පුට් කරන්න ඔනද මාෙන වගෙ ඇම්පියර් ගානකින්ද

I use it too, the grey one.

Best explanation! Thanks a lot man. Never mind if it’s not in English, the translation was perfect. I understood everything. Thank you! My pack works now!

Oke...input voltage ekata 60v දිලා 12v out karaganna puluvanda.

Me buck converter 2k parral krla used krnna පුළුවන් da

Hello the voltage reading on my module was not the same as the voltage of the battery

Can this module be used for the sim800l module? According to the required amperage of SIM800l, is this possible?