Відео

@@muhammadivandi6806 not sure what you mean, do you mean the update failed on the software? Thanks rich

​@@SURGE101Mine suddenly couldn't be used, model error, MCU firmware upgrade failed

@@muhammadivandi6806 try connecting it to the I2c platform and performing an update to the firmware as it may be running old firmware, if this doesn’t work I’ll look into trying to find a resolution for you. Not come across that issue before but I’ll do some research and try and resolve for you. Thanks rich

@@SURGE101 can i get your wa number sir? thanks...

It’s due to the barcodes on the tips, on the tips on the irons they have a barcode which the station reads and sets the heat offsets on the station automatically for each tip so the tip is outputting the same temperature as shown on the station. On the hakko hot tweezer tips, there no barcodes so the heating offsets are not being automatically adjusted. So the actual temps are different to what’s being shown. It’s a design flaw with this particular station. Thanks so much rich

Hi I totally agree, I did manage to return these rolls in the end thankfully as I bought them through eBay and they agreed when I opened a return. You’re right, if more people returned these bad products for a refund it would force them to make better products. Thanks so much for taking the time to watch the video . Honestly I really do appreciate it. Thanks rich

@@SURGE101 just make good content and the people will come 😉

@@davadoff thanks so much, really appreciate your kind words. Thanks so much rich

They don’t unfortunately supply a code sheet but I’ve been recording readings from known good working boards for comparison. Every working board you get take a reading and save it to compare against. I’ll post my record sheet once it’s more complete. Thanks rich

Hi I found this link for them but it may not be the cheapest, so it may be worth having a look around for the best price. Where they are genuine metcal nozzles, they’re not that cheap . Link below. Thanks rich cpc.farnell.com/metcal/hn-hct2-bent-6/nozzle-set-bent-6-pack/dp/SD02484

Hey bud having exactly the same issue as yourself, I2C Soft version VV1.4.96 along with NAND soft version 2.16, downgraded the firmware of the programmer to v1.00 and still getting "model error >>>>" message. Not sure what else to try at this moment :(

Check if you have imei , could be the sandwich layer, when you soldered the boards back together when you changed the Wi-Fi ic. May not be an unbinding issue. Thanks rich

@@SURGE101 everything works fine...if a put back the old wifi ic it works but with a new one it doesnt. I've tried several time the unbinding proces but same result. I dont know why it says wifi is unbound but in reality it isnt.

Once you upgraded to the v2.10 p15 pro software , just click the device upgrade button on the top with your p14 pro connected and It bring up the box and from there are the firmware files you require for the downgrade. Thanks rich and thanks for taking the time to watch.

Hi I’ve done a more up to date video about this programmer, please check my latest video. Thanks rich

Once you upgraded to the v2.10 p15 pro software , just click the device upgrade button on the top. It bring up the box and from there are the firmware files you require for the downgrade. Thanks rich and thanks for taking the time to watch.

Hopefully it helps someone and thanks so much for taking the time to watch. Really do appreciate it. Thanks Rich

Hi , happy new year. Thanks for taking the time to watch the video.much appreciated. If you’re looking for a Tristan tester, the blue Tristar tester in the video or the icc pro v2 are the best. The usb c tester in the video measures the pins inside the port and gives you the values for each pin. Comparing it to known good values , allows to detect if something wrong on that particular line. Thanks rich

Hi any device that’s a10 cpu or lower , the nand can be read or modified using the purple mode function which doesn’t require nand removal. Any newer the nand will have to be removed to read or modify etc. when first setting up, download the i2c platform software and then select the p14 pro section. This will then install the p14 pro software for you. Then plug the programmer into the computer. Then on the software select drivers from the menu. Once you’ve installed the drivers the programmer will appear in the software for use. It won’t work unless you install the drivers. Thanks rich

diode readings AAIK

Will be doing a more detailed video and demonstration once I got it fully setup and going. Just setting it up at the moment and making a few mods etc. ironing out a few problems with it at the moment. thanks for taking the time to watch, much appreciated. Thanks rich

Thanks for taking the time to watch, much appreciated. Rich

Here is a link to introduction user manual video from mechanic…. ua-cam.com/video/GA6tjsaGXtQ/v-deo.htmlsi=Zx8JWXUnHiofCSKN

@@SURGE101 Ok, I watched your link, but I do not know what do the numbers 1-12 cover.For example: OL/10, or 16/0,17 and 17/0,66. What is 10, what is 16, what is 17?

@@gagasgaga8213 hi, they are the values of the pins inside the port , links for diagrams for lightning port www.google.com/imgres?imgurl=https%3A%2F%2Fi.stack.imgur.com%2FX6soe.jpg&tbnid=yKQm5V4TlxkmSM&vet=1&imgrefurl=https%3A%2F%2Felectronics.stackexchange.com%2Fquestions%2F377424%2Fhow-to-make-the-lightning-port-of-iphone-output-5v-power-like-otg-on-android-ph&docid=-AqDWlF3oQSKIM&w=268&h=445&hl=en-gb&source=sh%2Fx%2Fim%2Fm4%2F7 USB c port diagram components101.com/connectors/usb-type-c-connector-pinout-datasheet Hope this helps. Thanks rich

Hello, I'm thinking about buying this device, but I still don't know how to use it after the detection of the issue. I mean, which detail should be replaced after the detection problem. Can you explain a little bit more? Please.

Not sure what you mean?

Try cleaning the pads of the nand, it may be the pins in the programmer are not making a good connection.

@@SURGE101 tried 3 nands same thing, might be the programmer itself being faulty. It detects the nand but cannot program

@@darriencriag2328 push the plastic down inside the programmer to reveal the pins inside the programmer and check they all come out properly and also cleaning the pins inside the programmer may solve this as it may be some dirt or something stopping the pins making a good connection with the nands.

Thanks for your input Yes I have tried that, even disassembled and reassembled the programmer

@@darriencriag2328 I’ll try and find out a solution for you and ask around . It may be a fault with the programmer. Unfortunately I’m not sure what could cause this to be honest but I’ll try and find out for you.

Hi to solve this issue you need to download and install the drivers from i2c. You can do this by opening the i2c platform and you will find the drivers in the the menu. Once installed it should recognise the programmer inside the software. If it opens the drivers and not installing the drivers when you try to, you may have to disable ‘driver enforcement’ inside windows to install. This is because windows sometimes stops you installing drivers that are not digitally certified by Microsoft . Hope this helps. Thanks rich.

Try a different usb type c cable The one it cones with sometimes does not work Had same problem and changing cable worked

The software for this programmer is so buggy that problems seem to arise from every update they release almost. One thing to try with the latest update, is to uninstall both of the programs from the computer completely. Then download the latest i2c platform program (the original one that’s shown in the beginning of this video). Then select p14 pro on the top left corner within the program itself (on the updated version of the platform )it will then download the latest version of the p14 pro platform shown later on in the video. Because it’s downloaded through the platform rather than the link it should work then. It’s a good programmer when it works but the software a nightmare unfortunately, the software updates are so buggy it almost makes it completely unusable at times. But hopefully that works for you as that’s how I managed to fix the latest issues. I’ll do an updated video soon on. Thanks rich

Thank you for taking the time to watch. Thanks rich

Hi, wofür ist dieses Gerät? Was kann man damit alles machen?

@@SunshineSunny-kn6hf Hallo, es ist ein Tester für USB-C- und Lightning-Anschlüsse.

Hola, puedes actualizar tu programador conectándote a la computadora y luego abriendo la plataforma de software i2c p14 pro. en la parte superior hay un símbolo de flecha grande llamado "actualización del dispositivo". Si hace clic aquí, actualizará el firmware del programador al firmware más reciente. Con suerte, esto resolverá los problemas que ha estado teniendo. gracias rico

@@SURGE101 muy agradecido por responderme !…. Pero lo e intentado varías veces y no me actualiza la programadora 🥹

@@JHONNY徐杰尼 Intentaré encontrar una solución para usted. Normalmente debería actualizar el firmware de esa manera, no estoy seguro de por qué no funciona. Podría ser un dispositivo defectuoso, pero intentaré encontrar otra manera. gracias rico

@@SURGE101 saludos ya hable con la gente de soporte y listo cuando se hace un formateo profundo hay que colocar la nand de nuevo en placa para que haga las particiones y luego bajar y volver a montar, asi se recupera la informacion de la nand o board.... y lo otro es que si no quieres formatear a nivel cero o low, entonces se escribe una configuracion generica generada por la misma unidad y desde alli se puede borrar o hacer lo que desee dependiendo del caso,,,,, es muy rapida esta programadora ..... gracias por ayudar

Try again in a while, it may just be the server down. Or delete all your browser history and then try. May be an installed cookie problem.

@@SURGE101 I can't find P14 Pro only i2c assistan v4

@@hossamhrmobilerepair3656 i2c have updated the platform since this video, if you download and install the i2c assistant and then once you have created an account and signed in , select the p14 pro in the top left corner. It then install the p14 pro software for you and will open automatically through selecting it in the i2c assistant platform.

SDG electronics has reviews of solder and flux. Episodes #79 and #86. You could buy solder from real electronics store, wherever you buy parts like Farnell, digikey, etc. Even JBC sells solder I think.

It’s most likely the drivers for the programmer haven’t been installed. Along the top of the software platform there should be a drop down menu and then select drivers. Once you’ve installed the drivers it should work for you. Rich

Which heating module would you recommend? I’m a beginner and I’d like to learn mobile repairs. Could you please recommend any tools to me.

On this version the modules just slide into the slots at the top but mechanic has now released a updated design to this preheater that includes a locking mechanism that locks the module in place. You are right This version the modules are loosely fitted. This video was when this product was first released but it’s since then had some minor tweaks to the design. Thanks so much for taking the time to watch, really appreciate it. Thanks rich

I’m doing well thanks , hope you are too. I changed the name of the channel because there are too many channels with a similar name and thought it’s best just to change it to something different. Thanks so much for taking the time, I really do appreciate it. Thanks rich

Much appreciated, thanks so much for taking the time , really do appreciate it. Thanks rich

Yes it has all the same options as the regular app, it has all the preset nand SYSCFG for all the models. When you select the model you can auto fill the data. Thanks rich

That’s a good question because I had server issues with the jc programmer p11. If the server down you can’t use it. Yes you can use it offline but within the i2c platform on the pc but certain functions like querying and purple mode need a connection. But to read and write , can be done offline. Thanks rich

Thanks Jesse, was a nightmare when it stopped working after updating. Rich

@@SURGE101 I needed this to work, since my JC P7 was also not working haha

😂😂I ended up changing it because there way too many ‘micro-repairs’ on here.😂, thinking about it ,the download link I showed in the video may of only worked because the opera browser I was using has a built in VPN. Glad there was a work around. Appreciate you taking the time. Thanks Rich

Ah yes the words Micro & Repairs do seem to show them self's a great deal in electronics. I honestly think the name you have gone with fits well. I tried to download the software via Chrome & Firefox with VPN on then i turned it off and still got the same blocked message. I did post the Link that included the IP to the software so i guess YT was right to delete it 😂

@@Ratchet_effect 😂😂thanks, not sure why that’s happening but I’ll have a look and see if I can get a better link, I’ll try and post a link to it in the description. I2c programmers are good for the money but the software a nightmare 😂