- 15
- 126 775
BigJers Observations
United States
Приєднався 19 гру 2019
Stihl 039 Muffler Modification Complete Applies to 029, 039, MS290, MS310, MS390
Complete Muffler Modification of Stihl 039, same work applies to the 029, 290, 390, Stihl MS290, MS310, MS390, and clones of these models by Hulzfforma, Farmertec, and Hutzl. I call it complete because unlike many modifications that put more or larger holes in the mufflers shell to assist the gases to get out, this modification does that but also removes the material inside the muffler allowing the gases to move within the muffler much better. For example the first cuttings in the video show the performance of the standard/most common type modification. In this modification you see what can be done when you have a complete modification. Once finished with any modifications to the saw that affects flow always retune the saw as necessary, and for those that still want to use the spark arrester screen, these cuts were made with the screen installed.
Переглядів: 15 858
Відео
Hulzfforma G366, Stihl MS361 muffler mod 30% Boost performance, re-engineereing muffler
Переглядів 6 тис.Рік тому
Muffler Mod to Hulzfforma G366, Stihl MS361 clone. Upgraded after 3 years in service. , DIY video starts with a current performance demo, then muffler removal, splitting the muffler, completely gutting all of the interruptions to exhaust flow. This includes the diffuser, the reverse inlet, the transition outlet to the rear, and the final forward deflector. Then reassembly with welding, painting...
Huztl G366, Stihl MS361 Clone, Fail, ?Flywheel & Key Again? Diagnose and Repair Intermittent Spark
Переглядів 2,4 тис.Рік тому
We Diagnose and Repair Farmertec G366, clone Stihl MS361, no run no start condition for Hulzfforma, (also referenced as Huztl, chainsaws. DIY, Farmertec, G366, Hulzfforma G366, ms361, clone, Stihl, clone ms361) trouble shooting of electrical intermittent/no spark conditions. Anticipate possible loose Flywheel and split key again. Once we are able to observe under the flywheel cover a loose conn...
Huztl G366 MS361 Clone Runs Backwards Diagnosed, Loose Flywheel Key Damage Fixed, Replaced Key
Переглядів 2,1 тис.4 роки тому
Holzfforma G366 and this time we diagnose engine performance issues. Identified the problem as a lose flywheel. Symptoms: 1. idle rpm dropped over 700rpm. 2. run backwards sometimes at idle. 3. loss of power in the cut. 4. very poor throttle response. 5. all issues were worse when saw warmed up. Results of disassembly inspection; flywheel keyway, and engine crank keyway both suffered minor dama...
Husqvarna HU675AWD Mower Self Propell Not Working, Diagnose Idler Pulley Repair, Husky DIY
Переглядів 42 тис.4 роки тому
Diagnose Husqvarna HU675AWD Mower with failed selfpropelled drive. After diagnosing the problem (idler pulleys), we do a step by step removal of bad components. This is a diagnose and dissassembly video. It does not address the drive pulley. But, that pulley pulls straight down and off with an alignment key and keyway.
Huztl G366 Stihl MS361 Replace Brake Handle also Holzfforma G366 Farmertec G366 How to DIY
Переглядів 4,4 тис.4 роки тому
Removing replacing a Huztl G366 or Stihl MS361 Brake Handle. The Huztl is also referred to as the Holzfforma G366, and the Farmertec G366. This is a step by step complete how to do it yourself video. Starting with the bar and chain cover through to the brake handle. Then we reverse the process starting with the brake handle right back to the bar and chain cover. Next is a static function check....
Huztl G372xp vs Holzfforma G366, Huztl G366 vs Holzfforma G372xp, Farmertec G372xp Farmertec G366
Переглядів 9 тис.4 роки тому
Demonstration cuts that highlight how similiar the times are on a 14" log. The times would be closer if the G372xp was not modded, or the G366 was modified. Stock or modified these Farmertec, Hulzfforma chainsaws are very capable and do a fine job. If we want to see how well the clones hold up with years of wear, we will just have to wait years. This video was taken approximately 4 months prior...
Huztl G366 Stihl MS361 Diagnose Plugged Fuel Tank Vent
Переглядів 3,5 тис.4 роки тому
This is a diagnose method to identify a plugged or partially plugged tank fuel vent on the Huztl G366 and Stihl MS361, as well as many other chainsaws and 2 stroke motors. Once the diagnose is complete, then you can watch the repair video to change a bad fuel tank vent.
Huztl G366 and Stihl MS361 Replace Fuel Tank Vent
Переглядів 5 тис.4 роки тому
How to replace fuel tank vent on Huztl G366 or a Stihl MS361. Shows DIY replacement from start to finish, with test verification run. If your chainsaw is running leaner particulary at high rpm when the engine fully warms up, and you pull the fuel cap and discover that the fuel tank developed a vacumn, you may want to try this very inexpensive, fast, and simple repair. Watch the video for Huztl ...
Huztl G366 Clone MS361 Update, Side Plate Repair Hulzfforma Farmertec Copy of Stihl MS361
Переглядів 2,2 тис.4 роки тому
Side plate repair. Plate was discovered rubbing on chain when I saw some sparks late in the evening . Believed to of been rubbing all along but I never noticed it in the daylight. Removed the plate, bent it so it would be flush with the side of the case. Ground off the burnt plastic from the oil tank. I should of noticed it sooner because I could never slide the chain backwards. I was to busy t...
Chinese Chainsaw Review and Starting Chinese Clone 62cc 6200
Переглядів 13 тис.4 роки тому
Starting Chinese Chainsaw, and Review Chinese Chainsaw. This is a one year review of a used 62cc / 6200 Chinese clone chainsaw with a 48mm cylinder very similar to the 47.5cc cylinder of the 6200 cloned redmax or zenoah . It also covers basic starting of a clone with a fuel / carburetor bubble. This saw was damaged and well used when I got it. Did several minor repairs, and cosmetic painting. U...
Repair Chainsaw Chain Repair Chain Damaged Tooth on Huztl G366 Clone of Stihl MS361 Clone
Переглядів 6514 роки тому
Repair Chain Tooth that was burnt. Heat Damage from nail strike. This repair is a DIY, howto video. When the chain dragged the nail in the wood about an inch and a half, the chain rode on the nail for about an inch and a half it created enough heat on the tooth to case harden the gullet of the tooth. The case-hardened section of tooth would not let a file sharpen the tooth. Repair work performe...
Huztl G366 MS361 Clone at Work Holzfforma Farmertec Clone of Stihl MS361
Переглядів 2,4 тис.4 роки тому
Video of the Huztl G366 Limbing and cutting up a dropped 65ft southern pine beetle (SPB) infested tree. Saw is still at breakin settings Observations: 1. Saw stalled one time during return to idle after cutting. 2. Easy to start, and restart. 3. Runs well, and idles even. 4. The entire tree was processed in 9 minutes. Opinion: 1. The saw is easily worth the money spent. 2. Nimble: This is based...
Huztl G366 MS361 Clone FIRST CUTS Holzfforma G366 Farmertec G366 Clone of Stihl MS361 Copy
Переглядів 10 тис.4 роки тому
Observing the Huztl G366, ( clone of Stihl MS361 ), Gentle cutting during first tank of fuel. A Tractor Supply 3/8 x .050 x 72 tooth, 20 inch, combo chain and bar that are listed as compatiable with a MS361 are installed. The combination of this bar and saw provide a very light chainsaw package for the amount of horsepower ( 4.6hp ). Adjusted the low speed screw to lean the idle prior to the vi...
Huztl G366 First Start Holzfforma G366 Review, Farmertec G366 Unbox, MS361 Clone Stihl Clone
Переглядів 9 тис.4 роки тому
This observation video is of the Huztl G366, Holzfforma G366, Farmertec G366, ( clone of Stihl MS361 ), as a 60cc class chainsaw. Covers Unboxing, Inventory, Inspection, and Startup. This Holzfforma saw was packaged very well and tight with lots of bubble wrap and additional plastic air bags. Inspection of the box showed how rough the package was treated after leaving Farmertec. The box appeara...
Si son bunoas esas máquinas????
12mm thin wall deep socket works perfect
Thank you
I have the ns872 a clone of the ms382 and I'm considering eventually doing that too. Luckly my muffler is bolted/screwed together, so opening it up and putting it back together will be much easier. My one issue is I have no way to weld the exhaust pipe onto it. So I may have to hire that done. But I love the increase in power you got. Thank you for showing us the difference without any extra mods. Great video. 😎👍
Thanks for your comment. Glad you found it helpful. Hope you enjoy that saw. All the reviews. I read about It looked pretty good, and it’s a nice size saw for sure.
I removed the main drive pulley and the key came out in two pieces. I am not sure what to do with that or how to get it back in place. I am going to assume I need a new key, but have not found any information on how or where to find one. Any help on where to get parts?
Sounds just like a Stihl!
Great vid. So my question is I'm having a problem with not being able to pull the cord. It's stuck and i have the exact make and model push mower. Any ideas where to start looking at first? Thanks..
Thank you for you comment. Answer: Unfortunately I do not have that mower with me. So other than trying youtube videos you may want to try this link: origin.kohlerenginesparts.com/oemparts/l/koh/61857843855d461d145af844/xt675-2075-husqvarna-parts Once you go to that site click on the page 07 starting Use it as a reference. remove the blower housing, about 3 nuts/screws. remove items 1, 9, and 4 as necessary. check for binding and free play as you go check the engine brake cable releasing check the blade under the deck after disconnecting spark wire/cable I am not a mechanic, just a tinker, but i would use this type of approach.
also try the shop manual: resources.kohler.com/power/kohler/enginesUS/pdf/14_690_01_EN.pdf pages: 32 and 33 is a good starting point.
Thanks for posting. I was able to change two of mine today. Thanks for posting. Much appreciated.
Glad it helped
New subscriber here from France...very informative video, out of interest how much louder was it after the exhaust modification ?
Thank you for subscribing and the question. I do not have a meter to measure them proper. My best guess is that there is about a 20 to 40% increase. If I am not wearing hearing protection I don't notice the volume change much but the tone is deeper and I can actually feel a small pressure on my ears after modifying the muffler. I always use hearing protection now.
I'll be!! I have been chasing a start - run - high rev - stall problem forever now on my ms361 (farmertec build) and this was it!! Well at least I am a master at doing Crank Seals now! Thank you!
Wow. Glad to hear this video helped you get her finally fixed. This was a little faster than doing those crank seals I imagine. Like you said, now you've got crank seals down pat, and a great running saw again. Mines 4.5 years old and I work the heck out of it.
Thank you for being so precise on how the belt diagram goes I search all over the UA-cam. You the one who the best tutorials thank you.
Glad you found it usefull an thank you for the comment
Used to be a to the point video on these saws and you could start it in 20 secs.Cant find that simple video anymore.
Thank you. Excellent point. For future viewers that want to get to the point they can scroll to 5:05. Then watch till the 6:00 point where the saw has started. I didn't make it in 20 seconds, but I do accomplish the basic task of starting the saw in 55 seconds, without additional explanations of course. Thank you again
Thank you! A lot of us small budget residential users have gone to gathering our own firewood to cut down on heating cost without wiping out the budget. For many of us this means getting free trees from Blow downs/dead falls or Clean up wood removal from tree fallers. i.e. we need bigger, more powerful saws(on a budget) Enter the Chinese Copies with decent power and somewhat acceptable performance, but not like the oem saws. I've noticed the 373 copies are very popular. They seem to be fairly reliable, easy enough to work on and if not pushed they can handle 24"-28" Bar/Chain combos. Problem is, as soon as you lean on them they tend to stall the chain in the wood. It looks like a Muffler upgrade would be the first and least expensive way to greatly improve performance. Your Modification to the G366 seems to confirm this. Again - Thank You!
Your welcome, and thank you for your excellent explanation of why so many of us opt for these clone saws now days, and we want to get what we can out of them. Especially low budget, low risk improvements that we can do with the tools we have. Thanks again and have a good firewood harvest this year.
Great job on the muffler! That saw has got some power! I have an old Sthil ms361 that I need to do the same thing!🤩🤩
Thanks, glad you enjoyed the mod. Hope you enjoy yours.
Thank you for the helpful information.
Glad it was helpful! Thank you for your comment
After muffler mod , did we need to tune carb?
I have always had to retune after modding. Thank you for your comment
Thank you I have the same mod. you help me alot thanks.
Glad I could help, Thank you for your commnet
That's amazing. You see right away even without the times
Thank you for your comment
perfect
Thank you for your comment
Nice... I think I'm going to get the kit and put on the big bore cylinder.... How is the antivibe?
It’s better than 029/039. I saw you have a 291. The AV system is not identical bet very similar to the 391. So I hope that will provide you with a good reference point. Thanks for your comments.
Thanks BigJer, great video
Glad you enjoyed it
Does anyone know what it is a clone of; Husky maybe?
Good question.
Now your going to blow it up. Faster air out faster and more air in. Now you need to re-jet the carb. If you don’t that lean burn will blow it up.
Thank you for your comment. I could of showed readjusting the carb. They normally run lean after the mod if you don't adjust the carb. I spun the H screw out about 3/16 of a turn then finished tuning with a different piece of wood that was not shown. I also could of max reved the saw outside the wood before and between the cuts that are in the video so you could of heard the four stroke. Thanks again for helping to make future videos better.
It’s the low “L” screw you need to adjust, not the H screw. The H screw is only used to set your max RPM. Need to turn that L screw out a 1/4 turn or so to richen up the fuel/air mixture.
@@SG-ig2th Thank you for your comment. I just want to make sure that you understand that both the H and the L screws are used to adjust their respective rpm by changing how lean or rich a setting is. As you change the ratio of lean vs rich you are also adjusting rpm. The simple version is: the L screw is the primary adjustment for lower rpms, and the H screw is the primary adjustment for higher rpms. The objective rpms when using respective screws are reference points in the tuning process. For example: you may have a saw that is max rpm rated for 13,500rpm but due to altitude, bar length, temperature, type of wood, and a host of issues you may need to use the 13,500rpm as a starting point and then finish tuning for optimum cutting effect "in the wood". I recommend that anyone desiring a better understanding of H and L screw adjustments, and 2 stroke theory might want to watch the following youtube video by Craig Kirkman: Episode 43: carburetor adjustment screws on 2-stroke. Many excellent videos are available on the web, and this one does an excellent job with the use of simple yet effective graphics. Thank you again for surfacing an example of another small yet important misunderstanding.
same saw, same mod (mostly) and i did it roughly 10 years ago. saw still runs great. i adjusted the carb but didn't rejet
Thanks for the 10 year update!!!
Mantap bro 👍
Thank you
Ikut nyimak
Thank you
new subscriber👍👍
Thanks for subscribing
Thanks for sharing.
Our pleasure Bob, and we appreciate the viewing
What the hell are you doing?!Why haven't you leave original muffler as it is?When service technician hears different sound
Thank you for your comment
@@bigjersobservations "thank you for your comment?!"Goood!
Did my muffler like your step one and an improvement. Doesn't seem to run near as hot. I am going to order another muffler and do like you did and do step two.. I check my jetting pretty regular with just a fine tune of a screw.I am not worried about warranty as it is out of warranty.I have the stock unmodified muffler but probably never put it back on.
I'm glad to hear that it is working out for you with the usual positive results. Good luck with your next step, and thank you for your comments.
@@dujeamizic3588 lmao u think i'm gonna take my saw to the 'service technician' and pay him $200 to work on my saw? I AM THE SERVICE TECHNICIAN
👍👍👍🙏🙏🙏🙏🙏🙏
Thank you for your comments.
👍👍🙏🙏💖🤟🤟🤟
Thank you
Great video. Thanks for sharing.
Thanks for watching!
Thank you for this video. I bought two of these over a year ago and neither one would start. Sold one and the other has been sitting. I've replaced everything I could think of (Carb, spark plug, starter coil, fuel filter, etc.) but I didn't know about this. I will have to give this a try and I hope it fixes it. The Farmertech community got mad at me when I complained about it online and they said I shouldn't buy these clones unless I know how to fix them. Farmertech wouldn't honor their warranty either (the saws were DOA) and said I should know how to fix them also. Overall, a very disappointing experience with them.
I hope it might help out. If you have no spark and because you have already tried spark plug, and coil, this just might be the issue.
These take factory Stihl vents?
Thank you for your comment. It should fit. I have never used Stihl OEM tank vent "# 0000 350 5800 Fuel Tank Vent OEM". However, They look identical and farmertec says that they are a direct oftermarket replacement, and they cite this Stihl part number.
I have this issue. Just bought a 5800 part. Have not installed it yet. Thanks for the video.
Yes
Good video 📸😊
Thank you. Glad you found it helpful
i have a 366, that the flywheel nut wasnt torqued properly which allowed the flywheel to move slightly when cranked one time. (i think) the engine backfired i immediately opened it up to find the flywheel loose and found the key inverted causing the key to shift and chip the key slot. ive considered using jb weld to repair the chip, but i reinstalled the key and flywheel as the chip damage was about 20% of the bearing surface. and cranked her up starts and runs okay i would suggest all 366 owners remove the flywheel and verify key orientation and correctly torque the flywheel nut.
Thank you for your comments Scott. You are absolutely right. Your comments caused me to look back at the running backwards video I made. When we diagnosed the problem it was a split key and as we took the flywheel off it was very obvious that the flywheel was loose. Nine months ago i received a comment from a viewer that had a bad running G366 and he had put 2 carbs on the saw., After watching the video he checked his saw and found a loose flywheel and split key. He replace the key retorqued the flywheel and now it runs fine. On other videos we have received comments about lousy runing G366s. I agree, everyone that owns a G366 might seriously consider taking the flywheel off, inspecting the key and slots and retightening the flywheel.
That's a bad habit to get into when you put on your chain brake, it should not even be bothered with,
Thank you for your comment
hi great video instructions , i have almost the same type , except mine has 2 belts , i had to change the belts , it took long time until i get my parts , now i gorgot how to put them back , i can not find single video like my model , dont know why ??? am i the only one has this HU 725 AWD/BBC , with 2 belts ???? please if any one has like mine or has one , if you can make a very clrar step by step video . or send me a link , by the way i have watched all single video on youtube , all they have one belt. 1 is short belt and second one is long like others , please some one helpe me out
Thank you for your comment. I am not familiar with your model. However I did a check at the Husquvarna support website and found 12 documents (manuals: owners, and illustrated parts lists, IPL).If you go to that website you may find the document you need with a diagram. The link I used was: www.husqvarna.com/us/search-results/?groups=DOCUMENTS&q=HU++725+AWD%2FBBC+ Good luck with your research.
Is the g366 still holding up
I've had one for 2 years and all is well...did have to replace the gas line..other than that it's been great!
Thank you
Great video,ty for making this for us.
Thank you for your comment
【from HIPA】Would you like to test my parts now?thanks
Thank you for your gracious offer, however no thank you
Just say or show what is needed..not a biography of mower
Thank you for your comment
Just wanted to say thanks for posting this video. I have the exact same saw put two new carburetors on it still ran like crap after watching your video I checked the flywheel key and sure enough it was sheared..
Wow, I love it when I find out that I actually helped someone. Have a great day, you brightened mine.
Oooooo People who put the chain brake on and then start it... Just makes me cringe That is absolutely hell on that needle bearing and clutch
Thank you for your comment
That's why i start on full choke until it "coughs" and then i put it in the run position.
Hold the throttle open then pull the choke out it should hold throttle open until you blip it
Thank you for your accurate procedural comment. I tried it on that saw like others, unfortunately it just did not work on that particular machine. Thanks again for your input.
Looks like the vent is in a great place to catch dirt and sawdust..
You bet is sure is. and thanks for the comment
your video is so good.If there is a chance to cooperate with you?I can give you free product for a long time.
hi friend, Have a good day. I am the promotion manager of HIPA，which provide accessories of Poulan,Husqvarna,STHIL,ECHO and so on. Are you willing to cooperate with us? Look forward to your reply.thank you
I am sorry. If I infringed on one of your products, I appoligize for that.
@@bigjersobservations Hi friend,you got it wrong.I want to cooperate with you.Could you help me to make video for product ?I will give you free product.
@@bigjersobservations hi friend ,do you like my products ?I will give you free one.
WHAT ABOUT THE MAIN ONE YOU DID NOT TOUCH I HAVE THAT ONE THAT IS BAD.
Thank you for your comment. Please disreguard my first response to your comment. The "MAIN ONE" you comment on I believe you are talking about the drive pully with the little star embossed on the bottom of it. Once you removed the blade you should be able to pull it down and comes right off depending on rust. Penetrating oil overnight should take care of that. If that star is sheared off then the drive will still work but the blade will stall in medium to heavy grass. Recommend replacing pully with new part. However I have welded a new star and then ground it to fit with dremel. Best of luck
"now let's go around top and get those other two screws." I found one of these at a curb, took two oil changes in a day to clear that up, now has a clean carb, works great. But those "two screws", that was driving me nuts, I couldn't figure out why that would come off. Thanks for posting this.
Thank you for your comment, and I'm glad you were able to finally get it finished.
So grateful for this excellent video. I have a two week old Holzfforma G366 and the chain brake is stuck engaged and pulling back on the handle won't release the brake. Not sure if I need to replace anything or just clean up and lube the linkage mechanism.
Thank you for your comment. I would probably try checking for rough edges and surfaces on the components when you go in to clean and lube. good luck
Great Video Only thing I would stress is TO CHeck if the Bracket holding the pulleys is still attach to lawn mower, My bracket had broken off at the screw point. so of course putting everything back together didn't go so well.
Thank you for your comment. Your absolutely right about that bracket.