Відео

Thanks 😊

hi, please give me the exact dimensions of the gear, I will try to draw and print it, I can share the drawing later and foto layer 1 and 2 and between.

Great video!!!

Hi, Can i have a question what paint do you use to paint the board? what do you use to make it rough? Thank you in advance for your help.

Thank you for taking the time to show how this is done. 👍🏻

Great, it worked perfectly for me, thanks.

Thanks for the video mate

Very good, thanks.

How long did it take you to replace the turbo?

Is this light just for the mileage ot the car needs ro be checked at a service? Thank you

Okay but how do you take the camera off if it’s tied up and stuck on the helmet????

Did you change the gasket on the cam cover or was it ok to use again.

My front driver side has gone I've rang the garage and no one wants to fix it because of some bolt there worrying about snapping and something about drop links i sont have a clue you look like a pro what's your thoughts on that brilliant video mate mine is the automatic version

Hello Michael, we are doing a project on a Seat Altea XL 2.0 2007 and your video was very helpfull, can you please tell me if your vehicle is Manual or Automatic, what are the main differences between a shaft for the two different gearboxes? Thank you. Regards.

Thank you mate Just changed it following your tutorial Red1 from Algeria

Do you need to turn the piston or can you push it back in?

That’s very good work!

With how many NM did you tighten the 2 bolts on the calliper? Thank you

Thanks 👍

Hii Welche Größe ist der Steckschlüssel für Radlager???

The best . Thanks .

What made you just change the boot and not the ball joint or whole driveshaft? If the boot was holed, wouldn't that have potentially damaged the ball joint?

Czarny filtr paliwa . Do roboty pompa vacum lub uszczellki na pompowtryskach

Nice job! Nice filmed! Ready to get mine out!

❤

Works on the Hero 10 as well.

Hi,I have a 2011 altea xl 1.6 tdi,from new,it’s been solid apart from a few repairs over the years and maintenance. But today it started to smoke a greyish smoke,no oil in the water tank or gunk in the oil ,idles fine,seems to have power,what could it be?

What was the issue? Thanks

I did it today! Thank you so much, this video really helped (Seat Leon 1P).

Thanks it helped a lot man!!

good video. will help me a lot when I have to change the brake fluid. how much brake fluid is needed? is one liter enough?

Just had mine replaced after 26000 km, but lots of them on own steam. Did ask for the old motor to be given to me And now I see this video! The repair by a bikeshop was 995 euro including work Do you have a recording of the sound it made?

Dziękuję dobry człowieku👍 zawsze zapominam.

Hola cuántos milímetros tiene filtro de gasoil de altura gracias

Music too loud.. your voice too far away… don’t do you youtube please.

Don't bother, they look naff and when dirt and brake dust gets between it and the alloy that is where your trouble starts.

Como vas con este motor BKD dicen que malo

Fuc*ing hell. How is possible a plastic weel inside the motor. My shimano bike is with motoe Shimano E6100 is it also with plastic parts hahahahahahaha but makes noise I mean norma as electric engine makes it. Thank you for the video sir. Could you help me to downgrade my firmware from 4.7.7 to 4.5.0 please

Hello Michael, do you have the link for the LEDs to order. Lg Michael

I have just discovered a leak in this area too, so your video is a fantastic reference. Can I ask, what is the silicone paste you used on the temperature sender? And did you use any sealant on the gasket between the flange and engine block, or new gaskets where the metal recirculation pipe meets the inlets?

Very smart, doing a chip tuning without updating the hardware 🥴🥹

Great video, but why did you remove the battery?

Thank you very much! I have to do the same on my Leon 1P

Great video iam doing this to the mrs car , can you remember the size of the spline tool to take off the wheel bearing as I need to buy one many thanks

Fantastisk video

f

Hi Michael and thank you for sharing really appreciate it. Can you please help, Got a 2009 Altea tdi 2L 140 bkd and the throttle body valve was stuck due to cog had snapped inside so I replaced it for a new one and when I shut the car down sometimes it’s juddering still and sometimes it’s fine!, Using OBD2 scanner got a p2108 code: Throttle actuator control (TAC) module - performance problem Any idea what this could be? I’m pretty sure I can still hear the valve opening and closing though just sometimes it shudders on shut down and sometimes It doesn’t.

Great video!

What was model year your car? Could you please tell me rear wiper blade (model number- brand)? Because I couldn't find correct wiper blade for rear!

This video is amazing :), but i dont now where. So you start with the slope B15 and start offpist when the fist curve come, on the right? And you end up with the slope B14 so you can reach the Stubnerkogel(16) middlestation?