Відео

Is it necessary to run anti-freeze through the outboard engine? I have not come across any videos on this topic. I have a Yamaha F300.

Awesome and extremely helpful video! Also thanks to Tom Whitlow comment for the tip on removing the taillight. ARE Revo truck cap on GMC 2024 Denali HD. Hardest part was getting the video lead through the truck bed and down behind the left taillight bc that is where the truck cap's wires were also run -- would not fit with both or even 1 protective tubing. What worked for me -- I pulled the plastic protective tubing off from the cap wires and then taped the video wire to two of the cap wires and fed it through both holes, then reattached the protective tubes to each set of wires from top and bottom. For the hole into the rear seat, I used a 1/2 drill bit through the hard plastic cap and then a 2 inch grommet siliconed to sit on top of the hole/plastic cap, then siliconed from both sides. Really happy with having the rear view camera back again after 2 months of looking through the tinted cap glass.

What size was the tubing that you purchased from the hardware store?

Pressure not speed

Dear sir - thank you for this video. Is there a way I can Venmo or PayPal you money for this video?????? It has helped me tremendously. This isn’t spam or a robot. 💪🏽💪🏽💪🏽

Mechanic replaced the purge valve, evaporator canister and did a smoke test and the p1450 code is still appearing. Any others causes for the culprit? I’ve noticed the check engine light comes on quicker when placed in sports mode

How is towing or when the truck is under sustained load for a brief amount of time?

I want the 4 dollar cans...Here in the Netherlands I pay 20 Euro for this same gallon bottle...

I have a hard time believing those self tapping screws aren’t gonna come loose. I’ve never seen anyone not bolt one on. I’d be curious how three years later it held up.

I see pumps that are 5 gpm. Has anyone tried going with more GPM ? My pump pressure sucks. So if that's a sign of it going bad and I only had the boat 3 years. Well I bought it used. So I don't remember having a lot of pressure from day 1. Has anyone replaced their pump with a bigger one.

Your video is very good and very detailed. My outboard motor also had a blockage in the cooling part, but I have one question: I don't know how to find the part numbers for these seals, such as 6CB-24482-00 and 6CB-14239-00. I would appreciate it if you could let me know. I look forward to your reply.

shouldn't that say starboard?

Great video. , was that the first time you replaced filters on vst you said you have 900 hours should I be looking to change my filters I have 400 hours on my 250. I change my other filters religiously and flush.

Poor maintenance

its the jellyfish launcher button

Thanks for uploading nice video, what kind of water hose did you use and where to buy?

I forgot to follow up with you following my succesful installation of the Rhodan 96. It's working like a charm and what a difference to have the capability to lock on to reefs and shut the engines off! Truly a game changer. So, thanks for the detailed videos on both the motor and electrical installation. Definitely made my life easier. On another note I was wondering if you've changed out the bungee cords on the below gunnel rod holders. I've ordered the cord online (3/16" diameter) and I guess I'll just size up the appropriate crimps once I have the cord. And advise?

Can it be fix by cleaning it??

we could not get a throttle blip to see how it sounds?

Merci beaucoup ❤❤❤❤❤❤❤❤❤

Merci beaucoup ❤❤❤❤❤❤❤❤❤❤

Very nice boat and well built. But you forgat range and price

You are a wonderful man, my brother, May friend . Thank you very much for your outstanding work. Your human brother will benefit from it.

Merci beaucoup ❤❤❤❤❤❤❤❤❤

You are a wonderful man, my brother, May friend . Thank you very much for your outstanding work. Your human brother will benefit from it.

Merci beaucoup ❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤

My brother, thank you very much for this distinguished and righteous work that you are presenting. Thank you very much. You have presented something that you will be shown mercy for on the Day of Resurrection with a righteous deed that will admit you to Paradise by my Lord.❤❤❤❤❤❤

Merci beaucoup ❤❤❤❤❤❤❤

Merci beaucoup ❤❤❤❤❤❤❤❤❤❤❤

Merci beaucoup ❤❤❤❤❤❤❤❤❤

Merci beaucoup ❤❤❤❤❤❤❤❤❤❤

Merci beaucoup ❤❤❤❤❤❤❤❤❤❤❤

New Yamaha’s?

Another great video.

Thank you. Awesome video.

Shame on Garmin to be selling inferior transducers. My GM 20 is only 2 seasons old and my Garming 5 striker is unable to connect with the transducer. I had a Raymarine before without any problems for years until it was stolen off the boat. Garmin should do a recall and replace FOC

Hola hoyga una pregunta tengo un motor 250 yanaha 4 tienpos con un problema me abienta aceite porla tapa deatras del respiradero despues deacelerar de media makina sino lopaso demedia makina no meabienta kepodra cer ya lepucimos anillos nuebos y ules de culata nuebos

Awesome video! Were you experiencing symptoms or was this just for maintenance?

I agree with ATR-42 Really grateful for your efforts. The part number help and all is great. I will say there is a super helpful and very simple way I've found to dispense ATF fluid. Use a piece of small tubing 1/4, 3/8, 1/2... as an artesian well kind of setup. Drill the cap with a uni-bit. Carefully drill it out to just slightly smaller than your tube. Cut at an angle on one end... makes it easier to push the tube through the cap and also allows the fluid to flow through from inside the bottle. Push the tubing all the way to the bottom of the quart bottle. Now you can simply squeeze the bottle of ATF same as Ketchup. Also, 3/16 or 7/32 drill through the top spout of a Dawn dish soap bottle and 1/4 tubing works great this way.

No bathroom?

You missed one

You should ask about the 40k dollar mark up from invoice on these boats. Dealers don't do much outside of taking money out of your pocket for minimal service.

Do you know where the location of the pressure valve control.

Thanks for the video, I just built my first rod leash and will work on my second one tomorrow. Very instructional and easy to follow. Thanks for sharing your knowledge and expertise!

Amazing, exactly what i need. I have a strange issue that i hope could be dolved by cleaning out the vst. I have a 2011 f250d. Its mounted on a Phantom 21 Speedboat. When i take it out in larger waves and jump with it, or get alot of movement. Suddenly the engine doesnt wanna rev past somewhere between 4000rpm and 4800. Differs from everytime. It runs perfect up to that rpm then it bogs. Seems like it wont get fuel to rev past it, no warnings or anything. Then i stop the engine, pump the fuel bulb, and restart, usually that fixes it. Then it happend again next time i get alot of movement on the boat.

Another excellent video! Watched this tutorial and realized I didn’t have an o-ring! Ordered what I needed and got this simple job done. If I hadn’t watched your vid the old o-ring would have went back in! Thank you so much for the great detail in your videos.

Thank you for an awesome video! Just completed timing belt and t-stats on my VF250LA. Your video gave me the confidence to diy! Thank you sir!

Somebody please tell me why you cannot simply just wire brush those anodes and put them back in. They show almost zero wear, only sea water crud. YAM wants stupid money for an anode. Made of quite possibly the shittiest metal on earth. Were they a buck or two a piece? SURE, toss em.

Excellent video! Was even easier todo than shown. Just had my starboard 2023 F300 with only 260hrs shutdown and refuse to restart. Figured it was the fuel filter, watched your vid, changed it in literally less than 5 minutes and we're back up and running. Thanks

What makes filter fill up and leak down half way..fill up and back down. Every 30 secs it fill to top and back down