Відео

Slick.. Who would of known. Thank you

Would you know about 3z415 speedaire. How many gallons it his

Just got a geo, has the same problem and it seems like a huge common problem. I did check my trans fluid and it was three times overfilled but i guess that was just unrelated. Thanks to this video and a bunch of old forums i can hopefully fix the transmission

Good video! I have a Speedaire 3Z428 that looks just like yours but it’s a 2HP. Got it for free from someone who was cleaning out their garage. Mine runs great but wondering where to get parts for these just in case. Thx

I have a sears craftsman 106.153781 same air pump need to find rings for it any ideas?

Thanks buddy!

You didn’t fix it

I just wondered this today so thank you 😄😁

Is the same transmission of the swift 1.3?

THANK YOU!! I was able to fix my lamp. I feel like I’ve accomplished something today!

great vid, you save me a lot money thank you!!!

Oh, you have to unplug it?

The U.K. wiring diagram for an electrical lamp switch is different.

Where are the instructions?

Your 3 year old video was exactly what I needed. Thank you!

Thank you so much for share this video i fix that board now the transmisión Is working thank you so much from Tijuana México

Hummingbird: X Wing Wasp: Tie Fighter

This helped me out! Thank you!

The suspense was killing me! Thanks for some really simple and clear instructions on how to repair this. I have a lamp that has the exact same problem. I now feel prepared to fix it myself thanks to you! I may have to cross my fingers AND toes, but I'm going to do this today.👍

30 weight oil is best if in warmer climate

Thankyou for sharing =)

I did just like you did and it still don't shift.

Walked outside. Did what you demonstrated. Took 3 min and fixed my issue!! Thank you so much!!

Took a while, but very good directions. Thanks

Is this the same for a 1997? Mine doesn’t have working blinkers but the hazard lights work, also starts in 3rd.

I cut a small piece of Gauge wire and put the battery in and then stuck the piece of wire where the spring was. Worked perfect 👍👍

Stop stealing the bins from USPS!!!

LOL, I just picked of the 20g 3z419j last year, and I had the exact same HF one as you. Probably overpaid for it at $150 but its the spitting image of the one my Dad had. These are nice not only because cast iron, but you can reconfig the motor to 220 with directions right on the front. Just replace the purge valve with a low profice brass one from Amazon for like 2 for $8, next I want to pull that valve off and use my $10 eBay boroscope to see what the inside of the tank looks like. Go check out some vids on what these do when they blow, it ain't minor. Once tuned up, this is going in the corner of the garage inside a nice 2x4 box. Out of the way, and somewhat enclosed is a reasonable safety measure IMO. I also keep the read wheels propped up an inch or so to insure water will definately drain but not enough to affect lubrication/sump. Opening the purge valve when I'm done, and leaving it open when not in use is my preference.

Thank you for explaining the principle of the switch mechanism! I was trying to install a switch on a cord that did not have one, and the instructions only said to make one cut in the wire. Needless to say, I could not fit the wire into the switch, nor get it to work properly. I should know by now to always search UA-cam first before undertaking any DIY project!

Thank you

thank you!! 👏

worked for me. Cleaned the plate and spring end/edges first with a model rail track cleaning rubber, fine sandpaper would probably do; then used flux. Left the spring a bit long and trimmed it until it was the right length. No-one would know it was repaired. Yes, I have a box of random springs salvaged out of stuff that broke.

Thank you so much! Very clear instructions 😊

Thanks

Very helpful. Thank you.

1:16 - That "dryer thing" is also a "regulator thing". Duh.

0:15 - 3Z460? DYSLEXICS UNITE !

THANK YOU!!

Worked like a charm.

OMG! Thanks for posting this video. The switch broke on my favorite lamp. I watched your video and bought the replacement part at Home Depot for $2.97. I was able to successfully put it on the lamp. So very happy that my lamp is working again. 😀😍😁

Thank you! I put a new switch like this on years ago, and of course forgot how. I learned a lot from your closeups, especially regarding the brass "pokey things" ! One fell out of the old switch after I opened it, and I could not get the "wheel"out to put it back in, and could not get it back in with the "wheel" in. I keep everything (except garbage) so I took a switch from an old cord that I wasn't using and followed your video and my lamp is again working!

I like this on a number of levels: 1. Clear instructions are given. 2. It honestly portrays literally any project I tackle at home... "hang on, I gotta find my pliers" "switch doesn't work... let's try a different bulb." No cut aways or edits... this is totally indicative of the "shit happens" principle. Thank you

how can I test each one to see if they are bad.???

Had one in 1980..same..good unit ..change the oil..every 3 months if u use it alot..

Love it. Just got the same compressor used. Wondering, after it runs is the top of the compressor head hot to the touch?

Mr. Dias, I'm replacing mine because turning the switch would cause a spark. How should I proceed since the wire is actually burned on one side. I don't want the new pointy thing poking into burnt black insulation. Can I cut out the burnt part of the wire and rewire?

I would give you a brotherly hug if I had you close. After a year of searching, I found the solution thanks to your video, the changes of my geo meter 1.0 revived! Thank you really, thank you

That set is 20lbs

Too fidgety

Reading the Amazon reviews some say: weld protruding into the tube blocks and causing plugging. Maybe this is why one of the tubes plugs up. I will repair, remove part of the weld, if need be with a round file. I ordered on from Amazon, don't have it yet.