Відео

How do you replace the side gaskets on the sunroof

Would you know if the 06 charger 3.5 engine has a gas filter

What was the part number?

Have to ask ...There is a plastic item on your saw work table , you never mention what it is... one was included in the skil ss9503-00 that I just purchased. I can't find it mentioned in the manual or list of included items. Later in your video you have moved it to the lower shelf of your saw table. What the heck is it?

Great job!

You very helped me, thanks!

Yep about a half a million bolts. You need a 14,13, and 10 mm unless your pulling the crank pulley. I just did the crank and cam sensors on mine, timing belt had been done with low mileage. The bracket for the A/C compressor is not fun. 1 single long strange bolt will drive you nuts putting it back in. It is about an 8 hour job period, at least.

This would have been extremely helpful if you showed us what that seal looked like up close given this model is now discontinued and if we could see the shape of the seal that fits on the windshield we could maybe find an alternative that will work

Do you have a link to get the rubber seal for the sunroof

Muy buen video, gracias por compartir 🙏🏽

Can you tell me where you found the replacement? I have the same issue with mine it is a 2008 Chrysler 300 C.

Where did you find the seal from ? Having a leaking issue

Thanks! Nice, slow step by step & informative video. Got my new seal & gonna try it on my Caliber today.

Doing it now

Thanks for the video, much appreciated

Another video not shoing how you get to the pump in the first place

Great video. I have a 2010 charger with the 5.7. Mine just started tapping and I am getting a misfire on cylinder 3. I did a coil pack/injector swap, misfire did not move. I just started the cam and lifter swap today. Thanks for the tips.

How much oil did you lose when removing the oil filter ?

Just got myself a top banana. How is your build going. How much hp you putting down??

Great video man. How did you clean out the rear drain tube? It seems hard to get to.

Did you change the coil-on-plug boots?

This is an amazing review, I'm purchasing one right now. I like your style!

Underrated Video 🔥

th

thank you appreciate this review..

Remove that magnet, correct?

I've watched several videos and everyone seems like they enjoy taking the driver's side off and showing it. But why don't they show the passenger side.

Hello your video was great I do side work and the video will help a good friend out think u Jerome from NC.

How intuitive is it to tune a CHARGER RT 07 with that tool ? I have a new camshafts, thermostat 180 and eagle intake manifold but dont know anything about tuning.

Thanks brother!

Would this work for an 08 caliber?

I installed an LED that lights up when my mds turns on my 300c 06 and acted exactly how you described. So I drive on dr 4 and my shutter goes away. Have you found out what links the mds to the torque converter? Is it when the mds engages it sends a signal to the tcc to lock or something? The reason im asking is because it also ocassionally stalls the engine. So i was wondering if maybe my torque converter clutch was staying locked causing my engine to turn off?

outstanding

Thanks for the video! I'm replacing the timing chain on my 2006 Charger R/T Daytona and was hoping someone had posted a video of this procedure. I assume yours is a Daytona as well since it's yellow. Mine is #251

I just wanna know how to replace my pump by taking off pan

My aisin bearings went out at 10k

I have a 2005 5.7 would this work to install the 6.4 oil pump into the 5.7. is this a simple job Thank you

Hey I know this video is old but did you put a aftermarket rear bumper on or is it just the angle? Looks smaller than mine. Might be the sticker too

Just picked up a 06 charger and need to replace water pump, feel pretty good about it after watching this. Easy peezy

Which tuner did you get?

It fix my issue thank you

Buy a foam cannon the soap go through the pump will wear out faster

Where did you get that seal from?

Be nice if you could hear it

Hello, what about on an 07 Chrysler 300 2.7, i see no videos

I sure wish I had the 2nd part to this video.. Just repaired radiator fan wiring but doesn't seem to be a place for me to secure the wiring to fan out of the way the engine belt.. Which is the reason they had to be repaired in the first place. Top 2 screws of the fan came lose from the radiator and now im stuck😭🙏🏽

If you’re from Texas, I’ll pay you to replace my sunroof on my charger 😭😭😭😭

Jeez, yes, the one thing that I needed to know was the belt tension at the adjustable idler and this is the one thing not touched on.

Where buy this seal

Thank you!