Відео

Thank you very much mate . The video solve my problem

I just did this in my 2010 camry. This is by far the best and most accurate video out there for this process. A big thank you to the creator of this video. For the average DIY mechanic, such as myself, I highly recommend setting aside a day for this if you're going to tackle it and just realize it's going to take patience to knock it out. It's indeed a very frustrating placement of such a simple valve.

What kind of exhaust is that

Did it fix your oil consumption issue?

*15

So could it be the oil filter I believe mine has it missing with code p0005

I was going to get another alternator but I’m going to check out the red wasn’t sure where it was soppose to go. But now I do. I checked the yellow and purple was good.

Mine ML is 350 and is little bit different set up, but your idea is working. Many thanks!!!

Please show how you install the swing arm?

How did you install the extension frame?

Good grief. Too much work . Horrible job. There’s to this other video by car car nut and he shows not so much work . I’m going to try his way

Thank you I had the same issue the check engine light wasn't turning on on mine either

My fan is not spinning even after turning the car on how do I fix that ?

It is a pain in the butt. Wonderful design by Toyota.

I’ve been putting off changing mine for over a month now. I’ve already changed the solenoid myself

Whats that called

PART# 15845-RAA-A01

no part name or part numbers?

Cuando agasbun bideovadlo bien sino nilo intentes porque no ayuda en nada nomás para ablan mal deti

your the greatest

thank you so much save me 250

Thank you

Thank you thank you thank you

Whats the mileage on the vehicle?? My honda is leaking from the back of the engine near the firewall

Thanks for doing this video. I just purchased a 2011 and was going to attempt this based on the many other videos out there without the ps pump. After I got the hose off from the top, I found this video since no other video showed the power steering pump. After watching this video, I decided this was too much work. Thanks again and you've got a subscriber now!

It's underneath, well that just sucks! All my other cars were as you said, on top and easy to get to. To the shop it goes sad to say. I'll do it at the same time I replace the serpentine belt. Thank you for the video!

That sounds dope mine is going to look very similar is your seat lowered?

If you have a 2011 you are not going to be able to remove/replace the hose from the top or from the pcv connection unless you remove many components to gain room. I advise against doing this job as it's too much trouble for DIYers and too expensive to take it to a shop. Change the oil every 3k miles.

How were you able to fit it to the ruckus?

Is a very difficult job. Had to take out the plastic manifold out with fuel rails air intake and a lot of plugs. I did gasket valve cover too with vvti orings included. Pcv hose was broken so had to replace it too. Didn’t had to mess with the Power steering pump

What’s the name of that gasket you replaced or did u used RTV?

Kia yh ap seal kerna chate h

Any tip on the middle belt? Got stuck😢

this job is ( pretty much involve)😂👍

just wondering why you turn off comments for the 2012 BMW video?

Thank you, only video that shows the pump in the way. No one believes that it is the same engine. But after watching this, I'll just keep toping off the oil instead. 😂 Less of a headache.

Nice video, it literally took me 6 to 7 hours with short breaks to remove it from a 2012 Camry. It took patience but I was in it to win it!

Did you have to drain the coolant before doing this?

Can barely hear you talk

Def helped me out bro thx

I am entirely illiterate when it comes to mechanic speak holy shit

Is this for a 4 cylinder engine?

Typical Ford design. They must really hate technicians to inflict this garbage on us.

Thank you

THANK YOU SOOOO FKN MUCH I BEEN LOOKING FOR THAT SOB. And holy damn it’s more work than changing the timing chain?!!!

Built these with big bore kits n swing arm extension with custom rims pipes carbs goes 75 mph no problem n fun

Can I just say thank you for this video! I literally had the exact same issue with fuel gauge etc.... You've saved me a lot of messing around. How did you know the REM went to sleep?

Awesome. Wonder if this great reset for a MBZ radio module will work for a screen that has gone to horizontal lines mostly black? Anybody. Or if have to buy a new head for the dash.

Thank you so much!!!!

This is a better design than the previous model CRVs