Відео

Agreed

They don't make a kit for the ce you'll have to make a custom kit I know a guy on IG made a kit similar to this its aggressive I really like it

@@Tseringzzz your most very welcome I'll try and remaster it a little later it was one of my 1st videos

@@matiasrivas8251 all I did was the efi I didn't do the engine swap these motors can handle about 1.5bar of boost without any probs normally on a healthy motor again that's on a healthy motor if you want to play it safe I would say 8lbs of boost is more than enough and will be fine if you wanted to add arp bolts and a new gasket make sure it's all good there you can most definitely push more it all just depends

@@drjohnespy it sounds like you replaced just about everything after you do get it running run some seafoam through the tank it will help clean it out some

@@thebenzhouse Thank you for your kind response. I will pick a couple of cans up tomorrow! Again, "Thank you!"

@@drjohnespy always man if you ever need any help let me know I'm more than happy to help if I can have a good one and good luck with your car

No you do not because your not going to be using the trigger teeth on it soxit will be perfectly fine

@@thebenzhouse yes it makes sense hahahaha. Thank you very much for your reply. is there another option for the O2 sensor or is it just the one from your earlier clip that you show?

@@piskota2488 your most very welcome and the one I posted is the easiest one you could use from what I learned

@@thebenzhouse im about to order ecu can you link yours that you used because i live in Balkans and everything is harder to find because of shipping and customs Edit: I cant find your instagram

It's a brand called monstaliner I highly recommend it

@@thebenzhouse I’m going to look into it for my Ml500 ! Thanks 🙏

@@thelongranger55 yea we want to get another one we miss it

Do it best swap ever that's for sure

Alzor wheels

Nice man I'm glad they can help out and congrats on your new car

I didn't use it on this but yes you can just gotta gather information to be able to use it is all

That's not a stupid question at all the 60-2 trigger wheel is the most generic trigger pattern for just about every stand alone ECU made so it's easy to use without doing a bunch of other work the OEM crank trigger 3tooth setup I don't think is compatible with the ECU and if I'm being 100% honest with you I've never tried it the stock sensor would most likely work if you cut the end and figure out if it's a 2 wire or a 3wire sensor

It's not meant for Mercedes TB it's from a bmw you can make an adapter if you really want to this is more of a diy with normal tools most people have laying around. I was just trying to show it can be done.

@@thebenzhousedoes it need to hold a tight seal on the throttle body or just clip onto the rod? I already shaved off the metal to mount the bmw sensor.

@@leocrisafulli1882 it just slides on the rod there is no seal or air that goes to it

@@leocrisafulli1882 you are more than welcome to msg me on IG as well I can respond faster ECT 😉

We made ours if you don't have the tools I would say I think the kangaroos team makes them but I could be wrong ......

Yepp pretty much the same thing 😉

Hope it helps my good man 😉

Tar cobba! Beautiful!

Ok so keep it under about 6-8lbs you won't have any issues with the rubber under the flap and for the IAC add a hose clamp to it and you should be fine you don't need to go crazy when tightening it because it's barbed

@@thebenzhouse Cheers ! 👍

Yes unfortunately I get customers cars done before my own so it was pushed back some but I will be doing videos of this for my own personal build here in the next few months

No you completely replace it with the adjustable one just the 3 bolts and it's out new one in and call it a day

Unfortunately it's gone now it's not there anymore

We ended up adding grommet because my wife yelled at me for it 🤣 I figured they would of been ok shouldn't move but yes we did end up adding grommets good eye

This job came out amazing such a perfect setup for the wagon I'm definitely doing this to mine 🤣 I love it

That's awesome man if you have any questions along the way feel free to ask away I'm happy to help if I can good luck with the job and have fun 😉

Right

Get over here bring Mike this weekend

Agreed

Yepp

Glad it could help this was one of my 1st videos ever I was so camera shy 🤣🤣 I was all discombobulated nervous stumbled on a few things I'm glad it could still help

Thank you very much I try man Im glad they can help out 😉