Відео

Imagine a kitchen with weird texture meant to look like some rustic French countryside kitchen. It is a nightmare. I am about to go see if I can scrape a small patch off. Wish me luck!

You can buy cheaper for less money

Pro list includes miter gauge, knife for marking, and oh I don’t know a tape measure.

Good Job Sir!

It’s not even the right size nail punch, you could use a circular saw, plastic wood is better, paint???

I have used that exact gun for base. If the wall isn’t completely flat then you’re gonna have huge gaps between the base and the wall. It has no power.

Just a few tips, if you are installing the same unit dont touch that piece thats hooked to your sink,it wasn't leaking before,let sleeping dogs lie,lol, also use the wrench that came with your new unit (tape it to the new unit), it works great to remove and install the new unit, it fits in those holes like a charm, much better than a screwdriver, after wiring the new unit get some black electrical tape and cover up those wire nuts,its a second safety "just in case"

About how long does it take for the batteries to charge for the first use? It's been about 2 hrs and the green lights are still blinking.

Im trying to figure out how to reset mine as well. From what I've gathered online and on UA-cam is you need to overinflate by 3:00 to 5 lb, drive for like 10 minutes around 50 mph, and then the system should use its own software to recalibrate the setting. Once that does, you can reduce the pressure back to what's recommended. Really poor software design to have such archaic reset options.Cars from Hyundai in other countries have a physical button that resets it.

Thanks Dad

This doesn't help. The pressure still shows low even though air was put in to correct level.

Help!!! I turn on the walking pad after a few seconds it goes faster and then turns off. What could be wrong?

How dang long does that take??? Yikes

I lose the remote do you know where I can get a replacement remote? The link where I bought it off Amazon is no longer available and I can’t contact seller

Thank you!

Great video! Thanks so much. I'm sorting the gasket now but my pool guy(as well as fitting the new gasket without first clearing out the old mess) did something with the top which means the lever doesn't have much spring! D'you think he may have tried taking the top apart? Thanks again

Now it keeps saying the person being weighed is "guest". EDIT: Duh, the last time I weighed myself it was off like 10 pounds. I just had to delete that last weigh-in entry. I always thought it used your fitbit bracelet to identify you, instead of your last weight.

Excellent little video. Thank you!

But you walls are green, throw chlorine in night before demo!!!!

I used this video as a reference and just did mine and have a few extra tips: Carpets were soaked, and the trough down each side of the kick panels were full of water. I used a shop vac to suck out the water, and then raised the front of the truck to get the water out that was pooled at the front to head to the rear to suck it up and also sucked what I could out of the sound deadening. Got 2/3 a gallon of water out of it! For the old seal remnants, I found that scraping it was not the right way, but used a lever action using a curved plastic trim tool to lift and pull it away. I then used brake cleaner (red can) and lots of blue rags to clean it up as this dissolves the old seal. For installation of the new seal, I did not smush it down like in this video; just laying it in the groove as you dispense off the roll, as you remove the backing paper at the same time is all it needed; it holds very firmly on its own just under its own weight. I’m also taking the opportunity to do the resistor trick on the heated rear window signal wire (when this loses continuity your heated mirrors and window won’t operate), and to drill the peg for the seat back release, so that I can tie a piece of paracord between it and the headrest mount to make it easier to drop in the future. Final recommendation is as soon as you see any moisture building up inside your F150, or it smells a little damp, don’t put it off - just get it changed! Mine is going to be parked up for a few weeks with a dehumidifier going to dry out the carpet (currently raised up on 2x4s to allow air to circulate under it).

The program feature doesnt work on mine,returning it.

Thank you 🙏 saved my butt today

Maybe you should have used the sounder and removed the textured wall

Great video! Does this kit support remote entry?

Wow great work!

Merci

Thanks!

I really like her lineup, im planning on getting her toaster next, ill probably make all my appliances beautiful appliances lol they look good too they follow through with the name

Excellent!!! Short and sweet, no extra nonsense. Thanks

does anyone know how to fix the actual container of the engine filter being detached from the engine bay?

What size filters do you use?

Save time and forget the starter lines. A lighter through the side works well.

How much was it?? It’s kind of pointless to mention “PRIME DAY DEAL” then not include how much the ‘deal’ was

Great vid really debating on getting one of these

Very, very helpful! Thank you.

My 2011 Versa thinks your problem is more likely with the battery than the MAF sensor...these Nissan cars have such an attitude.😂

Thanks Brodie

How much does a job like this cost? $$

Great video, but I still need to know where to find the plug to fill the holes.

On my 2010 4Runner its Trip B for step 1.

Thanks!

Thank you 🙏🏼

We moved and had issues with connecting--thanks for solving our issues!

Did the issue come back anytime after or was that definitely the fix? Having some issues myself today, figured I might try some of the cleaner.

This is by far the best view that helped me replace my garbage disposal. Thank you so much!!

Blades are hard for me to find also. If anyone knows of a blade on Amazon that works I would appreciate the info. Thanks.

Thanks for this bro .. I just noticed mine is leaking 🤦‍♂️

Tape measure, coping saw, angle-finder, scribing tool?

Leave the covers off.

Thank you, I went through about 5 videos with no luck, before yours, but got it done with yours