Відео

Where did you get it for 189. Everywhere I look it's 249

What was the starting problem? Great video!!! THANKS!!!

how was the drone on the freeways?

Why not just wait until you can do it properly. You could've done that properly for $50-$75.

Oakeyh

Ahhh fuck... I think I know what I'm doing tomorrow lol

Me likeee!

Is this legal to drive on the road ??

Wait can I just cut the muffler off and leave it or do I have to add a pipe like you did

Do you know what serie is it?

Will it work for a 2002 avalanche

Does it still have cats ??

🤦🏻‍♂️

I have a cub 48 with kawasaki fh 601 19 horse, can I put a fx 691v on it? Is it the same crank shaft size? Will the clutch fit? Thanks for your video!!! Happy new years!!!

Good video!° what was the problem with the starter not starting?

“It’ll work for now” story of my life😂

*A huge timesaver One last note🌾🌾 **allabout.wiki/Z254** this mower is incredibly powerful. During my pruning, I was cutting HUGE branches off some of the large trees. I would then stack the branches into piles, tie them together with a tow-rope, and connect the other end to the back of the mower. It had POWER-TO-SPARE in hauling the large piles of branches, and it didn't even break a sweat! All in all, a very nice piece of equipment...I will get a ton of use out of it!*

So you got a bad lifter

Will it pass smog ?

baby sounds just like a straight piped camaro🤤🤤

Does this set up have any drone?

What’s the price on the new engine

Happy wife Happy life

Helpfull and thanks for you service and protecting the community!

I’m changing my flexplate. Might drop the muffler while in at it lol. Thanks for saying to support it I’ve dropped too much shit today 🤣

Did it make a big difference after connecting the rest of the pipe back up vs just leaving the void in the middle?

Put the tune back to stock, and have no issues in the future. I did.

Picking up an 06 in a few days, can't wait to try it

Be sounds like Tim Allen

I bet its loud as heck at freeway speeds and no fun on long trips. Some people like loud I don't, although I would like a little more deep V8 rumble so I'm gonna go with a muffler change, I'm just not sure which one yet.

I've done a few different configurations on my 05. I installed a single to dual super 44 system the first time. I cut, grinded, mocked, and welded up a drivers side tailpipe that matches the side dumpout behind tire. Then i had bought a 3" stamped y pipe and deleted the super 44 with intentions of matching ypipe connector to the xpipe. That didn't happen that time around. Still had full back duals. I installed a 10 series before the stamped ypipe for maybe 6 months. Didn't like the tone so I removed the 10 series and had muffler delete single to duals all way back. Just bought all new piping to do new dual side dumps before the tire and will have xpipe tied in this time. Looking forward

🤣😂" its kind of a hack job lol"

ua-cam.com/video/pNq87iBZqUg/v-deo.html

Still got blown engine?

Hey man nice video, are the cats near the front? Just dont want to do this and it messing with emissions at all.

You said you were home alone ;-) How did you get the engine up and out? We are an older couple and are pulling out the dead B&S 25 hp out of our Ferris in the process of rebuilding or replacing it and are wondering what to grab or hook on to to remove it (when we get all the preliminary stuff disconnected etc.)? Thanks.

would this work on a 5.3 2004?

That new engine looks so nice! Lol

Did you ever go over that kawi motor? Could be something simple like needing a new head. I have the same mower, have had it for 8 years now. 600 hours.

I have a 52 inch liquid cooled Scag Wildcat I am having to replace a worn out Kawasaki engine on. I am going back with an air cooled Kawasaki engine. What kinda things you think I will need to address going from water cooled to air cooled. Thanks.

Scammmmmmmadvisor

Nice video I have a 2007 tiger cub with a 19 Kawasaki 500 hours blown 3 head gaskets already thinking changing motors tired of the blown head gaskets. What does a new motor cost approx. thanks for the video!

Nice truck and Good music, Radney Foster

Do you think itll work on a 99 chevy silverado 5.7?

Did you get the kamasaki that was made in China or the one that was made in the United States. One is better than the other

that v-twin on the huskvarna can replace some kawasaki engines. im actually replacing my old fh680v with a briggs and stratton

how much did you charge them?

I have the same 2 Scags as you. Got the cub 48 used and boy was that a mistake. The 52 cat was new and did great till it slung a rod though the case. I’m about to get a new engine and I was just looking at UA-cam to see if anyone might have a had the same issue. The Kawasaki 22 horse didn’t last but just over 3 years. I’m hoping the new one will be “better”? Thanks for posting.

Nice looking Scags. I just picked up a Toro Z Master with vac system. The 27hp Kawasaki is ticking. I’ve adjusted the rockers which I understand can get noisy. Seems to have quieted it a touch but definitely still there. I’m hoping it’s not something major. I do like the Kawasaki’s though. My Exmark Lazer has a 27hp Kohler. I’ve considered Scag but even used they’re big money.

Where did you buy it at