Відео

The other simple modification, is figure out the clearance at TDC and remove base gasket. Should it stay over about 0.020 thousands without the gasket. . I have one clone original edition 372 i did it to, plus a replacement 52mm piston. One serious low end power band. . Basically i was trying to create an obsolete gen 1 372 xpw that had a 51.4mm piston, thats no longer available worldwide. Its pretty close to the same performance.

Hey buddy you need to be wearing safety equipment out there and boots and everything you can't be out there in summer attire and be working like that

I hate these things with a passion. They make more noise than jet plane. And all these small engines put out more emissions than a car engine. Yet they don't ban them. Try using a rake. Make America skinny again.

What are you using the dress the wheel?

Bert I need a filling

I love my Echo saws. I have owned every major brand in the last 40 years. I liked my Jonsereds but you hardly see them anymore. My favorite was a Shindaiwa which is now the larger Echo's. They run great and are very dependable. Unfortunately, our dealer recently closed. That little saw cuts very well.

Nice tune up on that saw. It cut faster.

Being a Machinist , I'm sure if u did some cylinder work and all tht other mumbo jumbo , you could do some nice porting to sawz

There is a small difference in speed.

I think it helped some. I got a older husky I have been thinking about doing something like that to.

Good one, Bert. You never know if you don’t have a go at it. Great video….

I had to pull the limiter caps off the high and low speed jets to get a good tune after doing similar mods.

Nice video Bert. Little top handle ran pretty good stock for an older but well maintained saw. Snappier doesn’t hurt if the noise doesn’t bother you. I like your bucking table.

I did the same mods to a stihl 291 and the difference was definitely noticeable. Biggest change I noticed was the throttle response. Much snappier response after modification.

Good morning Bert!!😀😀

I have a CS-400 I purchased in 2007 I did a muffler mod to it now my 42cc saw performs like a 50cc saw. Great video Bert , keep on cutting

Looked like you had fun doing it. Satisfying inquiring minds is health. Well worth the time. Well done.

I've removed every spark arrestor on all my saws. They run better without them.

Nice modding 😊

Hi Bert nice video love it ( Ty Ron

Great video!! Poor man's fixes a lot of things!! Thanks for showing us ways to get more out of our small saws!! Stay Hydrated and Have a Safe Day

Remember cutting up toothpick all you need is sharp bucksaw is fastest thing per square inch in the wood 🪵 BERT . 😊

Bert a bread 🍞 chainsaw is all a bread 🍞 chainsaw . If you want noise 575 Cummins under the hood with straight pipe 😊. Now your talking ponies under the hood in a chainsaw . Probably should work on CHRIS 572 XP it need work under the hood for in the wood 🪵 yard . If iiiii iiiiii was you send it to DONNY WALKER chainsaw shop. Com got years of practice and know how to do work under the hood . Where your in the USA 🇺🇸 sent it IRON HORSE 🐎 got a good name for work under the hood in a chainsaw . In your case just take the muffler right off if your into noise BERT . 😮

Do you adjusft the rakers with the grinder or with a file?

Hi Bert: Do you change the grinding profile for different chains? There are a lot of people that just use one standard profile and they use that on all there chains.

Nice video Bert. Seems to be a nice,low budget way to sharpen. Camera focused up close and personal.

Good morning Bert! Thanks for the close-ups and walk through of your process. Cheers!

Nice job sharpening Bert. Great video.

Great video Bert! Thanks for having us along on this one! 🔥💯👍🤜🤛. Andrew from NB :)

Not sure if you noticed the tooth lifting up when you hit the chain stop. My grinder does the same thing and I usually have to hold it down then clamp it. Do this happen to any one else?

Nice and sharp! Great camera work👍👍

@ 5;35 YOU CAN SEE THE NAIL BITER. but later you explain. Good job

Great job Bert. If you cut a lot, that is a good investment. It is so much more enjoyable cutting with a sharp chain.

Great video! I just switched over to cbn and also bought a diamond for carbide. It has been a absolute game changer, sharpening 3/8 28" and 36" chains.. All 3 cost $320 from Sharpening Supply. Keep up the great video's!

Great video!! Like the close up camera work!! Stay Hydrated and Have a Safe Day

That grind is an eager beaver. Good stuff. 🔥

Having the opportunity to confirm my own grinder angles vs your setup was greatly appreciated. Thank You! I did figure out I needed to add about .005" to my raker height .025-.30" from what I would typically run in hardwood vs a conventional grind or hand filed chain .030-.035 on a 592XP, I have not tried this grind on a smaller saw as of yet.

Great close ups and camera angles, I generally wear a magnifyng glass/hood but this video made me think I would love your camera setup and my 28" monitor set up near my grinder. 👍👍👍

Thanks for answering the burr question. I was wondering about that.

Is there footage of the splitting that’s not sped up?

Great camera angles and close ups on the sharpening process. Is dressing your sharpening wheel parallel to the rail when angled over how you get the more square profile on your chainsaw teeth?

Bert you need a diamonds 💎 wheel . do a lot better job on the chainsaw tooth . Them stone that come with electric grinder is junk I just be told by peoples who sharpen chain for living. The same with hand 🤚 file get what you buy for working with NO name knock ✊ off stuff Bert . Remember a good 👍 sharpening stone probably cost 💲 more them the grinder . Same if you we’re running 🏃‍♂️ a bandsaw mill for blades and a good 👍 sharpening tool make beautiful timber for sure . 😊 you should have a contract keeping Chris chainsaw chains sharpen for him. 😊 take care

Thank You Bert nice video love it ( Ron

Nice demonstration video of how you do it 👍

Goes quick compared to Dremel 😊

That is some great close up footage Bert, what camera are you using?

Does the build up on the tooth stop affect the setting up of the wheel? Love the close up’s 👍

I’am burning bass wood & poplar early

People that complain about free stuff shouldn't be given free stuff.

A guy I know will soon have a farm conveyor ready for me to use in the woodyard. Going to be so nice to load dump trailers with it instead of chucking it and killing my shoulders.