Відео

Sir my amp onkyo 509 dts chip fald put analog chanal not work please help me🙏

Thank You.

This works for TX-NR515 for the record. Thanks!

Will this work on onkyo tx nr809 receiver?

Muito obrigado, eu tenho um tx nr626 que agora voltou a vida, eu moro no rio de janeiro Brasil.

Thank you, but it did not worked on my tx-nr414. I successfully switched it to HDMI ignore mode, and I hear third relay now, but there's still no sound. What else can be wrong with it?

Will the tone control works when switching to analog mode? Is this short key working for all onkyo systems? Will this idea work on TX-SR 506..i dont have the equipment right now with me...someone pls reply. Thanks in advance 😊

Hei! Kan du hjelpe meg?

dzieki bardzo

Thank you! I was almost ready to give up on my HT-RC270 after trying the chip heat and solder flow a couple times with no luck. Wish I saw this a couple years ago when my other receiver went out. I really hated losing it. Just make sure you have your speakers hooked up to the zone 2 terminals before trying this. I'm ok with not having surround and hdmi because mine was for stereo only setup. Thanks again!

Thanks for posting. I would prefer any language to none. I can translate speech but deciphering is more difficult.

i just got a consult 1 for very cheap,looks good but wont start up. battery voltage is 4.2 volts after about 45 minutes of charging. do you have an idea what the problem could be?

link na tie led mozes sem dat ci je to tajne? Pripevnoval si ich lepenim?

Is there anywhere I can get more info on this device like an instruction manual? Or find info on the cards? I have a Consult 1 and am trying to learn it, thanks!

hola, y para hacer esto en un tx-sr707 como seria ,gracias

Dobrý den/ ahoj... Děkuju moc za vaše video... Muj 515 ma stejny problém. Cetl jsem od vas pak článek kde to rozebirate detailněji ( myslim že v angličtině) ale uz ten článek nemůžu najit. Mohl byste prosim přiložit odkaz. Dekuju. Jirka

FACTORY RESET for the receiver by pressing the CAB/SAT button then pressing the power button. FACTORY RESET the remote by pressing the receiver button and home button until the red light stays lit, and then pressing the receiver button to extinguish,,,FYI.

HELP PLEASE! My white volume rocker is unresponsive on my remote so I used the unit volume knob for this. I can get sound with AM and FM radio but no sound via any HDMI source even though I get video. I even did a factory reset pressing the CAB/SAT button then power procedure and the factory reset didn't solve the silent HDMI sources. Can anyone provide me with some assistance? It's such a nice piece of gear to be unusable. Thank you.

Hi. I can't get the 3rd relay to click. I did as shown on video. I also tried to heat the dsp circuit. Didn't help.

This method works 100 % just did my 609 now plays via the analog cables . Plug main speakers hold power button and br/dvd button keep holding power till hdmi ignore apears them press power to diable hdmi . Ill advise u hv something connected to analog rca jacks either cd player or something have it playing tap on the source to cd ...

More info about LED SMD type?

it is necessary to have the remote control, since I did the procedure with a tx nr709 and if the relay is heard but it does not give audio

Hi, works for tx sr608? No have sound in any channel analog or digital =(

what is KISS analog source? FM radio channel?

Thank you so much Michal! As many others I am happy as can be to hear the full stereo radio sound of my old friend again. What could be the reason that I have no sound from the analog inputs? Thanks for any idea, Ulrich from Germany

Could it work even with my Onkyo TX509?

What about HDMI BD : DSPTH ?

where you get this device?

This is a really frustrating video. Even with the subtitles on it is extremely difficult to understand what you are doing and why.

Úžasná pomoc Michal. Už nám z toho v práci na predajni hrabalo. Raz to išlo, raz nie. Problém sme vďaka Vám vyriešili. Dali sme aj továrenský reštart. Neviete náhodou ako sa dá vypnúť "auto standby"? Prešli sme manuál na nete, ale nič sme nenašli. Ďakujeme

Damn, I have been struggling for ages trying to figure out what the hell was going on with my receiver. Thanks for this fix!

How to get back out of this analog button..

can you connect the cellphone to the tv/CD socket using an rca Jack cable from the cellphone to the CD/tv ..socket

This worked on my Onkyo 609. Thanks a lot Michal. This fix is AMAZING!!

It is Works for me

Nice.. Thank you so much. This receiver has been shelved for a few years now and now I can get some use from it again. :D

Thanks a lot for the video. It turns out. Can you tell me how long it works after this reboot.

Working thanks!

I wish I understand stood, the step by step procedure here! Words would be great! Said or written please help thank you

I would like to thank you wholeheartedly, my 515 worked, I'm from Brazil and I had difficulty understanding the video, but a link here in the comments also guided me, eases our frustration of having such an expensive and powerful receiver unused, this video is the best of all for at least it gives us a happiness to make the analog outputs work, thank you very much!

Hi great task. Do you know which card is for Nissan Maxima QX A32 from 1994? What do you think about the consult to USB devices? Thanks for answer Carsten

Worked on my 809.

Thanks so much. I have a 609 and 709 which both have the HDMI audio problem. I was ready to throw them both out after trying many workarounds. I saw your video just in time and they are both working in 2ch now, with hdmi switching for the video. On the 709 I even managed to drive all channels with neo:6 or PLII. Thanks again!

Sound that mate .... Some sound is better than nothing at all very clever you found this on the 616 model its bd/dvd and power button

You are a god sir

Procedure is step by step described in subtitles.

Dude it would help if you say somefhingvand explain what upure doing!