Відео

I have the same issue, do you know how to reset the warning messages? Thanks

This fixed worked for our steps that haven't worked in 6 months. Thank you so much for this content.

Amp steps cost the most and they use the cheapest plastic parts available. It’s ridiculous.

Great video. The issue though, that by this you're not fixing the problem, but just applying work-around to ignore the root cause. The serpentine naturally worn out after 100K+ miles. Replacement is the best way, otherwise if the belt snaps, it will cause much serious and costly problems.

LOVE IT!!! Are those tires 33/11.5r15?

Excellent thank you, I've had a 06 100 for 12 years and i won't trade it for anything 😝👍💯💯💯💯💯

Excellent diagnostic challenge,🤔😝😁👍💯💯💯💯💯🇺🇲

Did you had codes . Do you remember them

Great video, love the shop shirt!!🤘

thanks so much for this video! My driver's side was making the same terrible noise, and had the same issue. I never would have attempted fixing it until I saw your video, and was contemplating just getting some new steps - it works great now after fixing on saturday.

It's so Nice and shiny!

Make a hat for the alternator, just lost mine to a power steering leak 🙃

I put mevotech lower control arms on my 2018 Chevy Colorado and one of them snapped on me. Luckily I was in a parking lot and not the freeway, it was the TTX line as well… “rugged off road”

Looks great

Appreciate the video. Currently changing the starter in my 03 100 series.

I have a Toyota 1992 sr5 v6, and I want to put this old man emu kit, where I can buy it ?

Thank you very much! quite helpful

How long did the entire process (removal to installation) took? Thank you!

Hey thanks for the video! very clear!. Did you by any chance run into any misfiring while the pump was failing? or power loss during hill climbs? I am struggling with my 100 series too. I have been seeing ignition coils and spark plugs go bad shortly after replacing them with original ones.

Thank you

Fast forward to nearly the 15 minute mark to get past all the talking and get to the install

I was there yesterday. I was wanting a piece of Gilsonite for my collection. The American Gilsonite factory was secured like Ft. Knox. I think I saw where you were yesterday, but I didn't the time to get my drone out. Did you ever see any raw Gilsonite somewhere so that people could get a piece for a collection? Thanks! PS: coordinates? PPS: Did you or have you ever traveled over CO-139? Bikers would love it. I was white knuckeled going over it on my return trip at night!

Cheers your still champion. Thank you

Sweet truck!

If you want a little more out of these for heavy loads you could install the coachbuilder 1.5” extension from Ekstrom Design

Thank you. I just bought a 100 series and i need to do this.

I did my dad suspension with moog and after market parts for his 89 yota about 7 years ago its all giving out already. Doing mine in the coming months and sticking with all oem

Thanks for the info! I have a 94 FZJ so I understand

So I went ahead and dropped the front differential by removing a four bolts holding the crossmember, and then the two 19 mm bolts that attach the front differential to the frame. I didn't disconnect anything else, and used a jack to gently control the fall, in the oil pan just slipped straight out the back, not the front. And that was without removing the oil pickup.

These steps are hot garbage lately. I bought the XL's 2 years ago and 3 of the 4 motors stopped working, Good luck getting new motors under warranty by AMP Research, they will give you a run around asking for video proof then no answer.

What’s the purpose of the adjustment? Just to make it less noisy and annoying? Lol

At 3:56 not a homestead, part of the old camp used to house the miners since the site was so inaccessable. (PS Back roading? Always carry a small tool kit.)

Did it end up being an electrical grounding issue and not the starter …. That was what I encountered.

Figure I’ll add this, after about my 5th time re-watching for different tips you give and showed. My one bit of knowledge to share, is that it is usually ideal to wear gloves when handling bearings. The oils, sweat and crap from our hands can cause damage/eat into the coating on the surface of the bearings. Other than that, great video sir, helped me out a bunch🤟🤟.

Watching this thinking about those who don't even know. I can't imagine a better vehicle when everything is considered.

Great video, thx.

What’s the name of that organizer you had on your dash?

Same issue.2019 Toyota Tundra. My battery was almost 5 years old so I changed it and the issue went away. Try a new battery before you tear your truck apart. Just sayin'.

Thanks for the info. I am about to buy a new belt and now I will buy OEM belt from Toyota.

Do you know how to fix the wedge of the running board I have Yukon 2014

Original engine on the FJ60?

I think you might have the wrong length springs. That shackle angle doesn't look right

That idea for raising the upper control arm with the jack in the truck is genius!

Arguably the mostly reliable 98hp ever made. 😂 I've had several trucks from an 83 to a 92 and wasn't nice to them and they never let me down. One pieced together, factory turbo version was the most fun. 😁

Hi It s 4,2 or 2,8 ?

Nice old troopy. Are they bright rear lights or was he on the brakes the whole vid

Good job my friend I look your video next week I rebuild my 1994 oh, this is a great video. I have some idea from you.🙏

Bucket list

Chained up darkness lol😅

🤩 looking good, 70Toopy & 100do making the Utah outback drive about 🤙🏼