I bet that was so satisfying the first time you stood on a deck that you manufactured from scratch! Well done project- Looks identical to store bought.
@@befer it actually felt lighter and More snappy. Graphics wise, i dont have a silk screen. I used waterslide but waterslides come in sheets. So i couldn’t get the graphics as one full sheet. Plus considering the amount of work i had to put into it id have charge more then store bought. The catch is similar to my guitar making. When a robot is making it the value goes down. But when its hand made the value should go up. But then finding a buyer becomes more difficult when they compare it to mass produced versions..at least for me, lol im not the best salesman haha. So far its still holding up, but i haven’t skated in like 3 years now also haha
wow this is crazy I did this exact same thing as a high-school wood shop project when I was maybe 15 ( im 27 now). I remember I accidently cut a deck at 7.25 wide and gave it to my brother who learned 360 pressure flips on that same board because it was so narrow. He later landed too hard and snapped it. I was so sad afterwards lol
loving the element shirt. Good skating group. My brother was in iraq in the marines when he sent me my first hellium element board set up with there red wax and trucks the wheels where nice too.He even bought me a abunch of doh dohs and the first element movei. I ll never for get that.. I still even have the originals barrings he gave me. red bones barings. The company went out of business but eventully wound up making them again. Love thie vid. helped me alot. I want to learn to make my own board. gun give this a go. Thanks again sir have a awsome day
Just a thought... But if you used thinner planks (eg 20mm) when creating the concave etc, you might be able to fill in the steps/edges with a really strong filler, rather than relly on cutting away so much through sanding. It's just that the more you have to sand away, the more likely that your top and bottom mould will not really match perfectly. Which means a much weaker bond and way less deck strength.
I understand what you’re saying about how sanding the two halves of the mold individually technically creates dissimilar pieces which means theres some variation in in the press resulting in a weaker (albeit very slightly I’m sure) board. I also understand how using more, thinner planks increases the resolution of the copies, so to speak but I don’t know how filler would make it more precise than just sanding from that point? Also, how did you decide an exact number like 20mm for the recommended plank thickness? Is this a standard that’s in use in the industry? I’m assuming you’re referring to something like a resin or epoxy as the filler but I’m trying to imagine applying it and I’m not experienced at all with any of it but I’d imagine, if it’s the right consistency, you can pour it on and/or use something like a large plastic putty knife and special brush but would it really be more consistent? I guess the force on gravity is pretty consistent lol but won’t it also cause more to pool up in the concaves? Maybe if you exaggerate the concaves on the template that would make up for it🤔
I like this idea, a bit ! What I like is the idea of using narrower material for the forms. I think that a cheap and readily available material such as MDF could be used. It comes in many thicknesses. What I don't like, is the original idea of sanding, or the idea of filling. I think that if a narrow material was used, the contours would be close enough to be left alone altogether. Let's assume 10mm MDF, I could work with that using a jigsaw, as I don't have access to a bandsaw. But having never tried this, it's all speculation. I will have to have a go. I want to make a topmount dropdeck longboard of a slightly more compact length than my other boards.
There are 2 ways 1: Get a skateboard (Without the trucks) and trace it, make sure it’s still. 2: trace one half of a skateboard, cut it out, and then turn it around the other side and trace it.
Wondering if you’ve had any subsequent problems with the polyurethane glue? This could be one application where it shines. It’s very waterproof. But I’m concerned that it’s too thin and can’t bridge even tiny gaps except by foaming. Maybe no problem as even the foam is very sticky.
I'm pretty sure it is every song to every make it into a Casey Neistat video averaged together to make the most generic Neistat-esque youtube background song of all time.
@@kjbkarl Thanks.... It's been too long, since it was a holiday gift, but that is good info to know for next time. The stuff I ended up getting worked, but was a pinch thick. Still don't know what kind it is though :D The only thing it said on it was sustainable, plantation grown, and nontropical
hello bro , that' a very nice video . That's a super job . But can you give me the dimmensions of the woods you used at 0:19 in millimeters pls ? It would be very nice ;D
I tried to make one of these molds and I would suggest you 230 mm * 890 mm * 50 mm. It is important that the thickness of the wood is at least 50 mm :)
If You believe in Your Heart That Jesus died On The Cross And Rose again on The Third day and confess with your mouth that Jesus is Lord then you will be saved
This is definitely an amateur way to make a board.. but the proper way would be to layer 7 maple veneers to ensure structural integrity, and do press that in between your mold. Any money that board you made will break after a month of riding
@@hobojoe4494 Those three layers are thicker than the 7 layer. I do prefer seven layer of veener for flexing but if this works for the guy there is no need to follow the trend.
Yes, because there is only one way to do it. It’s in the Bible that way. Since Jesus had a cross made of maple and all skateboards are dedicated to Christ.
![Lp. Сердце Вселенной #60 РОЖДЕНИЕ ЛОЛОЛОШКИ [Финал] • Майнкрафт](http://i.ytimg.com/vi/YoR0pAV9FVQ/mqdefault.jpg)
I'm planning on making on of these with my grandpa over the quarantine! (My grandpa's a handyman)
That’s so cool! Miss spending time in the garage with my grandpa, always was a blast. Have fun!
David Jordon Miller thanks!
Ima going to just buy a mold but I gotta save a good amount of money
Lol me too my penny broke today
@@davidjordonmiller9686 mine died too
I bet that was so satisfying the first time you stood on a deck that you manufactured from scratch!
Well done project- Looks identical to store bought.
being a guitar builder and a skater...definitely making a deck. this video helped me decide on how to make my molds.
yooo, 3 years later, how did it end up? did u ever pick up the project ?
@@beferi made a few. Trying to sell them never worked out. So i just skated them for my self. Wasnt really worth my time anymore.
@@Icdezines were they comparable to the store bought ones at all?
@@befer it actually felt lighter and More snappy. Graphics wise, i dont have a silk screen. I used waterslide but waterslides come in sheets. So i couldn’t get the graphics as one full sheet. Plus considering the amount of work i had to put into it id have charge more then store bought. The catch is similar to my guitar making. When a robot is making it the value goes down. But when its hand made the value should go up. But then finding a buyer becomes more difficult when they compare it to mass produced versions..at least for me, lol im not the best salesman haha. So far its still holding up, but i haven’t skated in like 3 years now also haha
@@Icdezines quick question man. did you use plywood for the decks, or glued multiple pieces of veneer?
wow this is crazy I did this exact same thing as a high-school wood shop project when I was maybe 15 ( im 27 now). I remember I accidently cut a deck at 7.25 wide and gave it to my brother who learned 360 pressure flips on that same board because it was so narrow. He later landed too hard and snapped it. I was so sad afterwards lol
could anybody could help me to find the patterns for the mold ? the link in the description send me on the home page of DIY skateboards...
Yeah that website used to have a pdf file for it that shapes it to size but now it doesn't and I've been trying to find the pdf
Christian Devaul it’s under how to make a wood skateboard mold
www.diyskate.com/pdf/two.pdf
best tutorial ever, thanks for the pdf great job!!
loving the element shirt. Good skating group. My brother was in iraq in the marines when he sent me my first hellium element board set up with there red wax and trucks the wheels where nice too.He even bought me a abunch of doh dohs and the first element movei. I ll never for get that.. I still even have the originals barrings he gave me. red bones barings. The company went out of business but eventully wound up making them again. Love thie vid. helped me alot. I want to learn to make my own board. gun give this a go. Thanks again sir have a awsome day
Way better than other videos I’ve seen
cant wait to try and make my own! great video
Just a thought... But if you used thinner planks (eg 20mm) when creating the concave etc, you might be able to fill in the steps/edges with a really strong filler, rather than relly on cutting away so much through sanding. It's just that the more you have to sand away, the more likely that your top and bottom mould will not really match perfectly. Which means a much weaker bond and way less deck strength.
I understand what you’re saying about how sanding the two halves of the mold individually technically creates dissimilar pieces which means theres some variation in in the press resulting in a weaker (albeit very slightly I’m sure) board. I also understand how using more, thinner planks increases the resolution of the copies, so to speak but I don’t know how filler would make it more precise than just sanding from that point? Also, how did you decide an exact number like 20mm for the recommended plank thickness? Is this a standard that’s in use in the industry?
I’m assuming you’re referring to something like a resin or epoxy as the filler but I’m trying to imagine applying it and I’m not experienced at all with any of it but I’d imagine, if it’s the right consistency, you can pour it on and/or use something like a large plastic putty knife and special brush but would it really be more consistent? I guess the force on gravity is pretty consistent lol but won’t it also cause more to pool up in the concaves? Maybe if you exaggerate the concaves on the template that would make up for it🤔
I like this idea, a bit ! What I like is the idea of using narrower material for the forms. I think that a cheap and readily available material such as MDF could be used. It comes in many thicknesses.
What I don't like, is the original idea of sanding, or the idea of filling. I think that if a narrow material was used, the contours would be close enough to be left alone altogether. Let's assume 10mm MDF, I could work with that using a jigsaw, as I don't have access to a bandsaw.
But having never tried this, it's all speculation. I will have to have a go. I want to make a topmount dropdeck longboard of a slightly more compact length than my other boards.
How do i trace the length and width??
And how did you draw the shape??
There are 2 ways
1: Get a skateboard (Without the trucks) and trace it, make sure it’s still.
2: trace one half of a skateboard, cut it out, and then turn it around the other side and trace it.
How would you make the nose and tail different heights with this press or do you just not?
I wanna see u make a board n skate it. How durable is it
What materials do you need to make a skateboard
Inspirant, ça donne envie d’essayer. Merci !
Can you hydro dip?
where to buy a Canadian maple?
Momek p : Roarockit
Momek p grow one
@@bigdoinksinamish1265 and wait 50 years
Canadian maple ply wood?
eBay
Very useful thnaks especially for leaving the pdf
can't find the patterns, where are they please ?
Thickness of each board?
Wondering if you’ve had any subsequent problems with the polyurethane glue? This could be one application where it shines. It’s very waterproof. But I’m concerned that it’s too thin and can’t bridge even tiny gaps except by foaming. Maybe no problem as even the foam is very sticky.
please give full information on how to make a press mold
@@AaronAllenScaryBusey thx dude
A bit confused on the adhesive decal. Is it an adhesive vinyl or some other type of material? Also, where did you get that decal printed?
I also wanted to know..
what is this first song name???
Great tutorial
what is the thickness of that wood ?
What's the song? Also great vid
umm, what kind of plywood that is fit and kinda good to a skateboard? and can someone tell me the size of the plywood?
reza nurfajri from normal skateboard sizes i would think that 35 inches length and (if your making an 8.0 )
and 9 to 11 inches width
Great job
Could anyone help and give me a material list with all the materials?
what this song???
I'm pretty sure it is every song to every make it into a Casey Neistat video averaged together to make the most generic Neistat-esque youtube background song of all time.
what is the width of each Board that you used for the mold?
What would do you use for the stencil thing
Hey man do yo still have the template in your computer
drive.google.com/drive/folders/1zK3mjISkQyexChLLYiSJ3q407brhgtlP
this is really cool
were did you get the template for the mold
To anyone who sees this, god bless you and your family I hope this comment brings someone joy. You are all beautiful and amazing. Have a great day
Right back at ya ;)
what is the song used in the video?
The song is good but the board came out amazing
what song
Is there any European website or company from which I could order the adhesive papers with the graphics?
you could buy the adhesive papers and just download png. images online of what you might want in order to get a transparent background image to use
btw, where were you able to get the beams shown in the video, couldn't find them in home depot
@@ForzeVODS the beams are 2x8 ("two by eight"), they're in the lumber aisle. Ask someone in an orange apron for help.
What type of plywood is good for the board?
Veneer man. Canadian maple.
@@kjbkarl Thanks....
It's been too long, since it was a holiday gift, but that is good info to know for next time.
The stuff I ended up getting worked, but was a pinch thick.
Still don't know what kind it is though :D
The only thing it said on it was sustainable, plantation grown, and nontropical
Great video 👍🏽
Song @ 5:50 please?
Me podria regalas las medidas del molde con el que lo traza porfavor
www.diyskate.com/mold_02.html
Does anyone know where to find compression joints or any alternatives ?
In any hardware store :)
What is the thickness of the wood
thicc
Wats the name of the song
could i get a materials list?
Check this out diyskate.com/diy-skateboards.html you'll find all the information you need :)
Hello friend, could you pass the rest of the plans. greetings from Argentina
I wanted to see someone skate it !
Ya I like skateboards my brother use to put stickers and spray paint it and sparkle
Nice video.
Can you send me the templates?
How thick every plywood
1/16"
Is that centimeter or milimeter
Can anyone help me out with the measurements? I got lost
Song
I wish I had a skate board😄😊
Buy one or get a job save up and buy one
hello bro , that' a very nice video . That's a super job .
But can you give me the dimmensions of the woods you used at 0:19
in millimeters pls ? It would be very nice ;D
I tried to make one of these molds and I would suggest you 230 mm * 890 mm * 50 mm. It is important that the thickness of the wood is at least 50 mm :)
@@tinoskateboarding95 thanks you very much.
Link não abril
Very nice
at 0:2 what is this beat called
0:2
Why skateboard videos dont show how they put the wheels.
Need the song!!
how to ruin a original ´ Mudskin Cix´
will you make me a skateboard please? im super short and need one 24inches long instead of 31 :)
Can you make on for me
I dont really understand how to get the shape of the board
3 x 1/8" ply?! Every skater knows boards are made of 7 layers of Canadian Maple!! 🤘That thing looks like it's built for a horse
Great video.
Sad that i dont have any of the machines required. :(
This could be done with handtools and a jigsaw.
Jigsaws are cheap too.
Take a wood shop class
It is a very nice board just to thick for me personally I like a nice thin board
c'est quoi les musiques stp 😊
skateboard deck price $50
machinery to make a deck $50000
but the process of making is priceless😀
I am with u man. It's all about the process, what makes each handmade deck priceless.
I like that u used a spatula lol
You need to have 9 layers not 3
Kilian Curral not if your kid ways 60 pounds. And you use Poplar.
Kilian Curral it's 7 layers
he is using 1/8 inch ply wood not veneers... 9 layers is 1 1/8" thick... nobody needs a board that thick
The average board is 6 layers of Canadian ply
@@lubednoodle 7 Canadian maple, 1/16 inch
I wish i have a skate board
20k dollars or 100 dollars
Let me test it out 😈
Thank you very much. I'll try :)
ive seen so many woodworking videos i cringed when he didnt spread the glue and then screwed in the boards together...
ren as a joiner myself most wood working videos on UA-cam make me cringe
I don't think it was important enough to spread
Very cool but i think I'll just go to local skate shop
I wish i made this earlier
Coool
low smash always .
looks like kwebbrlkop
If You believe in Your Heart That Jesus died On The Cross And Rose again on The Third day and confess with your mouth that Jesus is Lord then you will be saved
j'aime les beignets 🍩
Me gusta los churros
Time to make a really ghetto skateboard
Work ,but its not a super Exactly Mold
This is definitely an amateur way to make a board.. but the proper way would be to layer 7 maple veneers to ensure structural integrity, and do press that in between your mold. Any money that board you made will break after a month of riding
Learn some manners
V
I purchased some excellent plans from the Woodprix website.
Moi aussi, j'aime le beignes LOL
I wanted to watch this entire video, but with all of the errors in terminology and misspellings I couldn't continue
lmao you aren't actually tryna build one right? so just watch the video with spelling errors or not
Mispellings or not I actually it is the best tutorial at the moment for building skateboards :)
why is the music so fucking annoying
pov: u wanna make ur own but u dont the materials
the song is annoying
honestly i didn't like the music cause it just keeps repeating and it gets annoying
There are many similar projects in woodglut's plans.
This is how Walmart makes their boards
DARWIN BALDWIN you’re supposed to put seven layers of maple not 3 if you only add three the board will snap mor like a Walmart board
@@hobojoe4494 Those three layers are thicker than the 7 layer. I do prefer seven layer of veener for flexing but if this works for the guy there is no need to follow the trend.
Walmart resells boards.
Yes, because there is only one way to do it. It’s in the Bible that way. Since Jesus had a cross made of maple and all skateboards are dedicated to Christ.
What is the width of the beams?
The width of a 2x8 is 1 1/2" each