well if you've got a month to wait there are a couple more things you can do like the battery and wheel mods ;) and maybe adding more weight at the back
Thank you very much for this. I just got finished now after spending around 5 hours at it lol. I had the exact same issue you did with the motors going the opposite directions even though I definitely put the red wire where the red dot was near the connector on the motor. I also swapped the wires on the plug like you did and that was that sorted. After I finished up, the loader itself developed an issue with going up but only if the side piece with the light/wing covering the servo was screwed on tight. I have solved it by dremelling off a few bits of plastic near where the limit switch is when its screwed on and that was probably because I shaved a few mm off the limit switch tip to get it to lift a bit higher. The little rubber that goes on over it might have been getting caught on there cos it has a bit more excess now but hopefully it wont happen again now. I fitted a driver while I had it apart and also greased the screws on the servos by using a syringe to pump grease into the outer rams while the inner parts were taken out completely. I did this to my Huina 1593 and Double E Volvo E591 A40G dump truck as well. I reckon its a good thing to do every now and again to stop wear on those screws. Thanks again for all the help you gave by putting this video up and happy new year 😎👍👍
Glad i could be some help. I think its more useful that i'm no expert at things, so any probelms i have are going the be the same as others might have :) just wish i hade more time and money to put into the hobby. I Want to get some hydraulic RC's eventually, but would take me years to save up for them lol Happy new year!
lol why not , if it ain't broke dont fix it lol. i would recommend doing the turning motor upgrade though , makes it noticeably better. i think i''ve seen someone replace the the drive gears with 4 motors instead, and esc for each ... i havent gone that far yet
I guess wheel slipping in the snow at my end hasn't had me consider this yet. Last fall in the dirt I thought it was suffice in the dirt. Will see after a summer of moving stuff will justify this mod. 🍻
I'm just hoping it can power through the dirt now , was getting bored of cleaning out the wheels. I'll have it out for a test soon, so i'll let you know if its worth doing :)
depends on how hard your digging with it. They do better then the stock ones, but i've got a lot less weight at the back now, so if your trying to lift wet heavy clay soil the back an hop up a little ...... i should have a vid coming out soon that will show that .
@@Granite-City-RC maybe weight the back wheels down or squeeze a lil more weight in the hull ? at any rate thanks man ill be looking forward to the video on that as i get mine saturday
Great video, I'm just about to do mine, I found the Magom video useless to watch, Yours is so much better. I noticed your never took the capacitor off the original motor and put on new motor, is it not really needed. Thanks.
If your running a V3 the V4 board is worth getting, from what i remember the V3 was more off/on on the throttle instead of being proportional. For the motors depends on what you are digging. If you have dry light material you might not need the upgrade, but if you are digging heavy wet material they are a good option. Also the wheel mod as well for a bit more traction in the tyres
Wow, what a great video! I was looking for exactly this! One question I hope you can answer. Did your Huina come stock with all 4 wheels driving forward?? I got the Top Race version of the 1583 and only the 2 front wheels drive forward and only the 2 rear wheels drive backwards. I thought the Top Race was an identical Huina “clone”, but did they cut corners, or was your 4 wheel drive a mod?? (As it is, my loader can barely get up an incline.)
depends on what you doing with the loader and if you happy with the current performance . if your only moving light dry material you probably wont need to upgrade unless you want to . I was moving wet heavy soil so had noticed a lack in torque , and for me it was worth doing the upgrade for a bit more torque
Very cool i just ordered a set because of this video said it will take a month to ship to America lol i am patiently waiting
well if you've got a month to wait there are a couple more things you can do like the battery and wheel mods ;) and maybe adding more weight at the back
@@Granite-City-RC I just weathered the paint and added a quick disconnect for the bucket and a driver figure definitely having fun working on it
Thank you very much for this. I just got finished now after spending around 5 hours at it lol.
I had the exact same issue you did with the motors going the opposite directions even though I definitely put the red wire where the red dot was near the connector on the motor. I also swapped the wires on the plug like you did and that was that sorted.
After I finished up, the loader itself developed an issue with going up but only if the side piece with the light/wing covering the servo was screwed on tight. I have solved it by dremelling off a few bits of plastic near where the limit switch is when its screwed on and that was probably because I shaved a few mm off the limit switch tip to get it to lift a bit higher. The little rubber that goes on over it might have been getting caught on there cos it has a bit more excess now but hopefully it wont happen again now.
I fitted a driver while I had it apart and also greased the screws on the servos by using a syringe to pump grease into the outer rams while the inner parts were taken out completely. I did this to my Huina 1593 and Double E Volvo E591 A40G dump truck as well. I reckon its a good thing to do every now and again to stop wear on those screws.
Thanks again for all the help you gave by putting this video up and happy new year 😎👍👍
Glad i could be some help. I think its more useful that i'm no expert at things, so any probelms i have are going the be the same as others might have :)
just wish i hade more time and money to put into the hobby. I Want to get some hydraulic RC's eventually, but would take me years to save up for them lol
Happy new year!
Thanks for this video! I’m going to use mine until it breaks then upgrade it. Hoping for more power.
lol why not , if it ain't broke dont fix it lol. i would recommend doing the turning motor upgrade though , makes it noticeably better. i think i''ve seen someone replace the the drive gears with 4 motors instead, and esc for each ... i havent gone that far yet
I guess wheel slipping in the snow at my end hasn't had me consider this yet. Last fall in the dirt I thought it was suffice in the dirt. Will see after a summer of moving stuff will justify this mod. 🍻
I'm just hoping it can power through the dirt now , was getting bored of cleaning out the wheels. I'll have it out for a test soon, so i'll let you know if its worth doing :)
@@Granite-City-RC Any new info about Magom drive gears ? Is it more powerful then original Huina? I am asking about POWER, not about grip, please.
@@EddieVichta As far as i've noticed there is better performance from them. they do seam to have a bit more torque then the stock motors.
Good job 🎉
Hello, good job friend 😍👏
Thanks :)
now that you did that wil it spin all 4 tires instead of the sort of kick in and out traction control system of huina's ?
depends on how hard your digging with it. They do better then the stock ones, but i've got a lot less weight at the back now, so if your trying to lift wet heavy clay soil the back an hop up a little ...... i should have a vid coming out soon that will show that .
@@Granite-City-RC maybe weight the back wheels down or squeeze a lil more weight in the hull ? at any rate thanks man ill be looking forward to the video on that as i get mine saturday
@@ShadeTree_RC Nice, they are fun to use in a very relaxed way. Were you thinking of doing many upgrades to it ?
@@Granite-City-RC yea in time id like to do the turn motor upgrade traction motor upgrade and tires/wheels
@@ShadeTree_RC sounds like you got a plan sorted then lol. That new video should be finished uploading in about an hour
Great video, I'm just about to do mine, I found the Magom video useless to watch, Yours is so much better. I noticed your never took the capacitor off the original motor and put on new motor, is it not really needed. Thanks.
Thanks. i either forgot or not noticed the capacitor, but it seems to work fine anyways lol :)
@@Granite-City-RC thanks for replying.
magom motors and v4 electronic board = worth it? is this mod helpfull for traction problems? very more power?
If your running a V3 the V4 board is worth getting, from what i remember the V3 was more off/on on the throttle instead of being proportional. For the motors depends on what you are digging. If you have dry light material you might not need the upgrade, but if you are digging heavy wet material they are a good option. Also the wheel mod as well for a bit more traction in the tyres
Wow, what a great video! I was looking for exactly this! One question I hope you can answer. Did your Huina come stock with all 4 wheels driving forward?? I got the Top Race version of the 1583 and only the 2 front wheels drive forward and only the 2 rear wheels drive backwards. I thought the Top Race was an identical Huina “clone”, but did they cut corners, or was your 4 wheel drive a mod?? (As it is, my loader can barely get up an incline.)
it was 4WD out the box mate, had to upgrade the motherboard to V4 to make it proportional though
@@Granite-City-RC Thanks for the reply! I’m torn about putting more money in it ATM. For limited use, it’s OK.
@@hobbycow5346 no problem, i know the feeling of limited funds and spending it wisely lol
Kde sa da kupit taky motor na zadnu napravu?
magomhrc.com/en/huina-583-hydraulic-conversion/1697-huina-583-traction-kit.html
I've done the steering mod, do you think its worth the money for this one?
depends on what you doing with the loader and if you happy with the current performance . if your only moving light dry material you probably wont need to upgrade unless you want to . I was moving wet heavy soil so had noticed a lack in torque , and for me it was worth doing the upgrade for a bit more torque
@@Granite-City-RC good to hear, ordered the bits last night )
Brasil 🚜🚛👍
very nice my friend naw you need to tho the rear suspecion tha its the real diference but very nice job
Thanks buddy, i enjoyed the build :)
👍👌👏🙏
Thanks :)