How to know it engine idle already on 1300-1500 rpm idle if i do it with no tachometer (manual adjustment)? Did you have a simple way to knowing engine idle level?
bro, i have fzs v2, problem is sometimes bike dont start until i have to give throttle, even after i recently changed battry, ant air screw, so can u suggest me what to do?..
@@MrBrijesh143 do few things : Clean the throttle body, replace the spark plug and also clean the injector. Check if the temperature sensor is connected properly with the plug. Clean the fuel tank and fill fresh petrol. If all this doesn't help, it can be due to a choked fuel filter inside the tank. Then you will have to remove the fuel pump and clean everything.
I have a problem with my fazer 2.0 just changed the battery recently because I a haven’t used for over 4 months after the battery change and when I start the motor bike it is automatically revving really hard I’m glad I put it on neutral other wise it would have run off. Anyways is there any way to fix this ?. Thanks
Let it fully warm up for like 5-10 mins and see what's it behaving like. If it still keeps revving, see if the throttle cable is stuck, else check the idle screw.
Fz version 2.0 injector model While running around 40 to 50 km speed Bike gets knocking or missing issue at the same time eco indication also gets off. Low speed and high speed no issue. Please solve this problem.
bro my bike is fz ver 2.0 after first service they raised idle rpm from 1.5 to 2 after soo many days i changed it to 1.5 is any problem is there in that and fzs idle rpm is 1500 know?
Bike not starting can be due to a different reason. Increase the RPM by rotating counter clock wise for around 5-10 rounds and start the bike. Then again start the adjustment.
Hey man,so i tried this on my r15 v3 bs4,and turning it clockwise or anti clockwise (atleast 3-4) turns didn't do anything,the rpm was same. What maybe the issue?
Hi bro , very informative video thanks for it. But my bike does not have that screw, i mean to say it is lost, where should i buy it , if you have any link please provide. What is the name of that screw
Bro my fz v2 rpm increase to 2_2.5k while turning fully right. I noticed that the accelerator is being applied automatically while checking the round thing below rpm screw.how to fix this bro? Do I need to change the accelerator cable??
Bibhash Sarmah We increasd air and fuel flow very slightly. So this will not have an effect on power or fuel efficiency unless your vehicle idles a lot.
Is it the same on the 2nd generation (2016) FZ150i ? I don´t have the manual unfortunately. My bike seems to idle at a slightly low RPM value and I wanna try increasing it but no idea how to get it done.
@@inderkapurthala1889 bro engineering work vale ke pass jake nut banwa lo 1000 tk me ban jayega agr nut hai to uska size deke same bana dete hai metal me unlog
You can adjust idles in throttle cables, if you turn the air screw counterclockwise you are making the fuel mixture lean and it cause piston breaks,you can only adjust aircrew unless you are using a programable ecu😁 i work in Yamaha as a chief mechanic.
Like in carburettor dont you have air fuel ratio screw and idle rpm screw. I see that below the throttle body there is a small nut which can be used to adjust rpm as well. It has to be adjusted with a hex/allen key. I am confused on why there are two ways to adjust rpm. Can you please clear this ?
EFI engines have the computer (ECU) which constantly measures the air intake temperature / pressure (throught MAP Sensor) and the exhaust oxygen levels using the O2 sensor. Based the the pressure, temperature, oxygen levels, it decided the amount of fuel to be mixed in the intake air using the injector. This process happens extremely quickly and the ECUs are capable to running 50-100 cycles in a second for achieving the perfect mix. So adjustment of af mixture is completely out of question as it's preset inside the ECU. The only thing that's adjustable in our non-ride-by-wire throttle bodies is the idle RPM which is shown in this video. For bikes that have ride by wire, the idle RPM is also company preset and cannot be altered.
@@dwaipayantalapatra6109 screw extraction process ... Where a reverse threaded needle is drilled into the broken bolt to extract it. Will be making a video on bolt removal / extraction soon.
Replace AirFilter Replace Sparkplug Change Engine oil Clean and lubricate the drive chain Inflate the tires to correct pressure Whack open the throttle in every gear till you redline and ride it like you have stolen it. But always ride safely and never over speed. Make sure you do everything in a controlled environment and not on public roads .
Hello guys, FZS V2.0 2016 model - My bike's RPM adjusting screw is damaged as you can see in below pic. Can any pl suggest solution on below.. 1. Can I get switch installed or I need to replace FI? 2. how do I increase or decrease RPM?
I have question for you Bro, maybe you can explain it to me... My FZN150 engine idle always decrease when it going hot condition and it sounds very disturbing me (it sounds like something knocking from engine). Is it normal?
@@bagassriindrantoro6807 the drop in RPM is absolutely normal. The ECU has a temperature sensor which raises the RPM when the engine temperature is low acting like a auto choke. After reaching operating temperature it drops to normal idle RPM. As far as sound goes the head is a lil noisy after heatup. Also clutch bell noise is present in most Yamahas. It's kind of a characteristic of Yamaha engine.
@@MototechWanderer any screw that will increase rpm on turning clockwise is idle screw, there are 2 screws on my R15 Fi , one is for controlling air (rpm increases on turning anti-clockwise) and one is for opening throttle idle position (idle screw)
This scre is broken.can i get new one?
You can order it from the contact given in the video description.
@@MototechWanderer how much cost?
@@MototechWanderer Where????how can i get that air screw????
@@shabeeralimuthuvallur2254 I guess 100-200 INR
@@MototechWanderer which website it provide???service center or?
Thankyou so much I have a FZS V3 and this video is so helpful !!
Glad to know. You're welcome.
How to know it engine idle already on 1300-1500 rpm idle if i do it with no tachometer (manual adjustment)? Did you have a simple way to knowing engine idle level?
With sound.
How to increase my fz v2 2019 model, how can i tune it.,please let me know
bro, i have fzs v2, problem is sometimes bike dont start until i have to give throttle, even after i recently changed battry, ant air screw, so can u suggest me what to do?..
Do you regularly use your bike ?
@@MototechWanderer yes bro
@@MrBrijesh143 do few things :
Clean the throttle body, replace the spark plug and also clean the injector.
Check if the temperature sensor is connected properly with the plug.
Clean the fuel tank and fill fresh petrol.
If all this doesn't help, it can be due to a choked fuel filter inside the tank. Then you will have to remove the fuel pump and clean everything.
Ok bro , ill do it , thanks for reply...🤗
Sir....throtle body can make it tik tik sound is it?
No it cannot. It's either the worne out throttle cable or the injector noise.
@@MototechWanderer i hear it from throtle body 😀 then how to solve??
@@mfgallery4512 if possible share a video of the noise.
@@MototechWanderer are you on whatsapp??...that sound is like a tapet tik tik sound!! But its not tapet
If i set it wrong, will it adjust itself with time?
Nope.
I have a problem with my fazer 2.0 just changed the battery recently because I a haven’t used for over 4 months after the battery change and when I start the motor bike it is automatically revving really hard I’m glad I put it on neutral other wise it would have run off. Anyways is there any way to fix this ?. Thanks
Let it fully warm up for like 5-10 mins and see what's it behaving like. If it still keeps revving, see if the throttle cable is stuck, else check the idle screw.
Turn your handle left and right to check the throttle cable.
@@MototechWanderer thanks bro 😀
@@ramimr1701 you're welcome
What meter you install down the main meter?
Is it clock?
It's a voltmeter.
Fz version 2.0 injector model
While running around 40 to 50 km speed
Bike gets knocking or missing issue at the same time eco indication also gets off.
Low speed and high speed no issue.
Please solve this problem.
Replace the spark plug and see.
I checked spark is normal
Replace the plug if it doesn't work, replace the HT coil and spark plug cable.
Ok thank you.
I will check and let u know.
My fz v2.0 2015's engine shutting down frequently while in low speed after running it in high speed, any suggestions?
Spark plug
Spark plug cap
HT coil
Spark plug cable
Replace one by one ... One of them is faulty.
Did issue resolved buddy
Air screw broken sir, any solution?
Take it to lathe to remove it.
Bhaiya agar ideal rpm ka screw tut gya to kiya krna hogha
Naya throttle body lagana padega alag se woh part milna mushkil hai
Is petrol reduces if we increase the rpm?????
No, no relation
bro my bike is fz ver 2.0 after first service they raised idle rpm from 1.5 to 2 after soo many days i changed it to 1.5 is any problem is there in that and fzs idle rpm is 1500 know?
Felix Lopez there is no issue with the idle RPM.
mileage is good for decreased rpm know?
Felix Lopez No change in mileage. Idle RPM doesn't play any significant role in fuel efficiency.
it does!!
Bro my bike is not starting after improper carburetor tuning. How to fix it plss help
Bike not starting can be due to a different reason. Increase the RPM by rotating counter clock wise for around 5-10 rounds and start the bike. Then again start the adjustment.
@@MototechWanderer thankyou for your valuable reply 😀. I tried by rotation the screw. Sometimes starting but off suddenly.
Replace the spark plug and see if it idles better
@@MototechWanderer ok i will try bro🤗
That screw is made of plastic and its broken on my bike. Please someone tell me where can I buy it. I tried to buy but its not available anywhere.
It's a very difficult to source screw. Only Yamaha Authorized dealers will be able to provide.
Worst case scenario, you have to replace the throttle body.
bro yamaha szr me bhi jab start krta hu to 1000rpm ya isse niche knocking sound ati hai or thodi heat hote hi band ho jati hai???
Spark plug change Karo.
Hello there bro were is the location of idling screw of yamaha sniper 150
Hey man,so i tried this on my r15 v3 bs4,and turning it clockwise or anti clockwise (atleast 3-4) turns didn't do anything,the rpm was same.
What maybe the issue?
May be the wrong screw.
@@MototechWanderer no bro,i am pretty sure about the screw,what else it can be anyways?
@@MototechWanderer what could be the reason,plz help
Something is stuck inside, service your throttle body. Start by cleaning the TB, follow the video in my channel to DIY.
@@MototechWanderer i recently cleaned it🥲,but all this happened after the cam bearing replacement,the service centre guys are messed up.
Hi bro , very informative video thanks for it.
But my bike does not have that screw, i mean to say it is lost, where should i buy it , if you have any link please provide.
What is the name of that screw
Yes you have to order that part from yamaha. I will check the part number when I visit the dealer next time.
Thank you very much.
It will be very helpful
Also subscribed 👍
They are advise to buy throttle body 😭😭
thanks budddy, from Philippines😉
You're welcome 😊
bro, can you please show how to install gear indicator by a video
Will try to make a video.
@@MototechWanderer thank you bro
Bro my fz v2 rpm increase to 2_2.5k while turning fully right. I noticed that the accelerator is being applied automatically while checking the round thing below rpm screw.how to fix this bro? Do I need to change the accelerator cable??
Adjust the throttle cable freeplay and your issue will be resolved
How to do that bro?
@@abidas738 there will be adjusters near the throttle. Rotate them clock / anti clockwise and set the right freeplay.
@@MototechWanderer bro I increased freeplay to maximum still the problem exists. The rpm decreased slightly and not crossing 2
@@abidas738 what's happening when u try to adjust Idle RPM like in this video ?
Hello bro I have lost that screw somehow.Is that available extra ?
Not sure. You have to check with the Yamaha dealer.
bro mila kya screw agr mila to please batao kaise mila mera bhi voi screw break hogya hai please
@@manmeetsingh4230 mera screw thik hai .. aap showroom pe pata karo. Authorized dealer k paas order karwao ... Woh log laa denge.
What does this control, the fuel intake or air ?
Just opens/closes the throttle slide to maintain a certain RPM. The AF mixture in always maintained by the ECU.
Very helpful bro thanx a lott...just a question, through this process we increased the air flow into the cylinder ??
Bibhash Sarmah We increasd air and fuel flow very slightly. So this will not have an effect on power or fuel efficiency unless your vehicle idles a lot.
hello man.. is that adjusting screw located at carburator?
It's the v2 model and has fuel injection system. For a carbureted engine, there will be a fuel screw.
Is it the same on the 2nd generation (2016) FZ150i ? I don´t have the manual unfortunately. My bike seems to idle at a slightly low RPM value and I wanna try increasing it but no idea how to get it done.
It's on the right side of the bike in Fz16 v1.
Bhai mera ye ghumane men tut gya ha ab kya karen 😭😭 or lockdown v ha kahan milega or kese lgana ha muje email kar do bhai 🙏🙏 please 🌹🌹🇮🇳💞🇮🇳💞🇮🇳💞.
Tutna toh nahi chahiye ... Yamaha dealers ke paas milega. Order karwa do.
bro mila kya screw agr mila hai to please batao kha se mila please mera bhi voi screw break hogya hai
@@manmeetsingh4230 mera bhi bc pora part change krne ko keh rhe. 3700 mein
@@inderkapurthala1889 bro engineering work vale ke pass jake nut banwa lo 1000 tk me ban jayega agr nut hai to uska size deke same bana dete hai metal me unlog
@@manmeetsingh4230 kise ki bike se nut niklww ke new bnawna leta hoon
Which is best for increasing mileage?
Rpm increase or Rpm reduce??
None of that is best. The best is to maintain the company recommended RPM.
@@MototechWanderer thankyou
thnx a lot.One of the Dealer was saying me that we can't adjust this speed 😅
Now you can give them a lesson on how to adjust.
You can adjust idles in throttle cables, if you turn the air screw counterclockwise you are making the fuel mixture lean and it cause piston breaks,you can only adjust aircrew unless you are using a programable ecu😁 i work in Yamaha as a chief mechanic.
Like in carburettor dont you have air fuel ratio screw and idle rpm screw. I see that below the throttle body there is a small nut which can be used to adjust rpm as well. It has to be adjusted with a hex/allen key. I am confused on why there are two ways to adjust rpm. Can you please clear this ?
EFI engines have the computer (ECU) which constantly measures the air intake temperature / pressure (throught MAP Sensor) and the exhaust oxygen levels using the O2 sensor. Based the the pressure, temperature, oxygen levels, it decided the amount of fuel to be mixed in the intake air using the injector. This process happens extremely quickly and the ECUs are capable to running 50-100 cycles in a second for achieving the perfect mix. So adjustment of af mixture is completely out of question as it's preset inside the ECU.
The only thing that's adjustable in our non-ride-by-wire throttle bodies is the idle RPM which is shown in this video. For bikes that have ride by wire, the idle RPM is also company preset and cannot be altered.
Bhai mera ye screw toot gya ab kya kru kaha se milega
Video description me ek bande ka contact hai, usse check kro shayad mil jaaye
This screw is broken in my fzv2. Can't adjust it now and it's in lowest possible position and due to the same reason bike stops in traffic.
Either try lathe on it. Last option will be to replace the throttle body.
Take a second opinion from the service center.
@@MototechWanderer great. Lathe wont be possible because the screw head is broken and the rest of threaded part is still in
Dwaipayan Talapatra I am facing same problem!! Any solutions??
@@mayankk_xo discussed above.
@@dwaipayantalapatra6109 screw extraction process ... Where a reverse threaded needle is drilled into the broken bolt to extract it. Will be making a video on bolt removal / extraction soon.
I need this Gear Indicator ..
How can i get This ??
Look in Aliexpress or Amazon.in
How to get top speed in 1/2/3 gears
Replace AirFilter
Replace Sparkplug
Change Engine oil
Clean and lubricate the drive chain
Inflate the tires to correct pressure
Whack open the throttle in every gear till you redline and ride it like you have stolen it.
But always ride safely and never over speed. Make sure you do everything in a controlled environment and not on public roads .
I need speak to you
Connect me on my Instagram handle.
Instagram name
@@dipstarofficial2386 please check the video description
Apaka rpm 1 raheta but 1reheat To bike 200 kms run bada hojata 2 rpm best please help me
okay
gracias saludos desde colombia
Gracias
Rpm increase karne se bhp thora increase hota hay kya ?
IMAN KALYAN Nope.
Hello guys,
FZS V2.0 2016 model
- My bike's RPM adjusting screw is damaged as you can see in below pic.
Can any pl suggest solution on below..
1. Can I get switch installed or I need to replace FI?
2. how do I increase or decrease RPM?
Place an order with Yamaha for the screw. It can be replaced.
How come v know that r milage is raise?
hiten solanki Use the tachometer to see the RPM. And a well tuned idle will keep engine healthy
Ok buro
Thank you!
Welcome :)
This will work on fuel injection bikes
This is an EFI bike.
@@MototechWanderer brother how can i adjust the idle rpm metre in my gixxer sf fi.
@@MototechWanderer i couldn't find any screw...can you help me out
@@harshithnarvaiye569 haven't got a chance to check Gixxer Fi yet. I am guessing there will be an idle screw there too.
Bhai apki bike milage kitna deti h meri Fazer to 35 ka milage deti h
Mera 40-45 deta hai aaj kal.
Pehle 52 tak deta tha constantly.
Tq so much
You are welcome.
You right bro...standard idle for this motorcycle is 1300-1500 rpm. But, why many people set it on 1200 rpm?
They are in false notion of saving fuel with a low idle. It's a myth unless we idle the engine for hours.
I agree with you Bro
I have question for you Bro, maybe you can explain it to me... My FZN150 engine idle always decrease when it going hot condition and it sounds very disturbing me (it sounds like something knocking from engine). Is it normal?
@@bagassriindrantoro6807 the drop in RPM is absolutely normal. The ECU has a temperature sensor which raises the RPM when the engine temperature is low acting like a auto choke. After reaching operating temperature it drops to normal idle RPM.
As far as sound goes the head is a lil noisy after heatup. Also clutch bell noise is present in most Yamahas. It's kind of a characteristic of Yamaha engine.
Moto Tech Wanderer :- The Fz version 2 engine is noisy when compared to the version 1
This technique is increas millage bro
Yes, slight improvement.
OK bro tq
thank
You're welcome ☺️
How to make the bike run rich and not lean
This is a closed loop EFI ... Can't change the AF mixture by any means except reprogramming the ECU.
Starting rpm b/w 3 to 4. What to do
Jassi Chana Do what you learnt in this video. It's clearly explained.
Mototech Wanderer but problem is that it fluctuate. Not stable
Jassi Chana fz v2 has temperature sensor. If engine is cold the idle increases and later drops with engine heat. Find the right balance.
Mototech Wanderer ok i will try
VDO mast h lekin bhai aap motovlogging kyu nahi karthe?
😉
Ajith kumar AJ Aap log support karte rahe toh vlogging bhi start karenge.
ji me raha aap k saath
Ajith kumar AJ Thank you so much.
bro it help to increase mileage
ràñgâ rãßçlè a little increase.
Thats the air flow screw
@@hastendmello you can call it that but remember this is a throttle body not a carburettor.
@@MototechWanderer any screw that will increase rpm on turning clockwise is idle screw, there are 2 screws on my R15 Fi , one is for controlling air (rpm increases on turning anti-clockwise) and one is for opening throttle idle position (idle screw)
i want this for cbr250r 2011 std broo
Figure out the screw ... Process would be the same.
Where is the fuel screw
Rejeesh Appu it's electronic fuel injection. Doesn't have a fuel screw.
How can we tone it?
Rejeesh Appu No tuning needed or possible on an EFI motorcycle.
👍
🌹🌹🌹🌹🌹🌹
Thanks 😊
広めてください」、
👍🏼
Abe galat idle speed set kar rhe ho.. always maintain 1400-1500 RPM nahi to battery ki life 2 saal se zyada nahi rahegi.
1300-1500 RPM ... Book me mentioned hai. Wahi set kiya.
@@MototechWanderer always use Tachometer device, not the bike's one because that is not digital as there are only lines blinking on it.
@@AnkitKumar-qb7rw I work with the approximation of the bike's tacho. Each blinking line is around 200 RPMs.
मवमरह
👍🏼
Thankyou so much easy video 👍
You're welcome 😊