How to Replace a Holden / Buick 3.8L V6 Water Pump FULL GUIDE / WALK THROUGH

Поділитися
Вставка
  • Опубліковано 10 жов 2024
  • In this Video I Show you all the steps of how to replace your old water pump. The process is almost the same for the old Buick 3800 V6 and the newer ECOTEC motors as well. Any V6 Commodore from the VN to the VY will use the exact same water pump..
    在本视频中,我向您展示了更换旧水泵的所有步骤。旧别克 3800 V6 和较新的 ECOTEC 电机的过程几乎相同。从 VN 到 VY 的任何 V6 Commodore 都将使用完全相同的水泵。
    En este video te muestro todos los pasos para reemplazar una bomba de agua vieja. El proceso es prácticamente el mismo para el viejo Buick 3800 V6 y el motor ECOTEC más nuevo. Cualquier Commodore V6 de VN a VY utilizará exactamente la misma bomba de agua.
    Dalam video ini saya menunjukkan kepada Anda semua langkah tentang cara mengganti pompa air lama. Prosesnya hampir sama untuk Buick 3800 V6 lama dan motor ECOTEC yang lebih baru. Commodore V6 apa pun dari VN ke VY akan menggunakan pompa air yang sama persis.
    इस वीडियो में मैं आपको एक पुराने पानी के पंप को बदलने के सभी तरीके दिखाऊंगी। यह प्रक्रिया पुराने ब्यूक 3800 V6 और नए ECOTEC मोटर के लिए लगभग समान है। VN से VY तक कोई भी V6 कमोडोर ठीक उसी पानी के पंप का उपयोग करेगा।
    Sa video na ito ipapakita ko sa iyo ang lahat ng mga hakbang kung paano palitan ang lumang water pump. Ang proseso ay halos pareho para sa lumang Buick 3800 V6 at ang mas bagong ECOTEC motor. Anumang V6 Commodore mula VN hanggang VY ay gagamit ng eksaktong parehong water pump.
    In diesem Video zeige ich dir alle Schritte zum Austausch einer alten Wasserpumpe. Der Prozess ist für den alten Buick 3800 V6 und den neueren ECOTEC-Motor ziemlich gleich. Jeder V6-Commodore von VN bis VY verwendet genau dieselbe Wasserpumpe.

КОМЕНТАРІ • 30

  • @DaRucksogsepp
    @DaRucksogsepp Місяць тому

    This helped me alot. Now my 00 Camaro v6 has a New Waterpump. Big thanks from Bavaria.

  • @yagmurcakir
    @yagmurcakir 2 місяці тому

    What an awesome bloke. That’s a job well done mate.

  • @davidsobin2405
    @davidsobin2405 5 місяців тому +3

    Awesome video mate. Just what I needed

  • @dasbsbih2491
    @dasbsbih2491 Рік тому +3

    Well done mate very informative, also using 2 bolts to hold the gasket flush with the new pump when installing is a great idea , top quality video! 👍

  • @nathanielgraham8588
    @nathanielgraham8588 Рік тому

    Need to change my water pump I'm confident doing it after this video cheers mate very helpful

  • @cpzmelbs
    @cpzmelbs Рік тому +2

    From memory the instruction sheet for the water pump mentioned the spacer only being needed for S1 buicks i believe.
    Working in spare parts I've opened many of these wp boxes and some dont come with the spacer at all

  • @TDFrank
    @TDFrank Рік тому

    You’ve just aren’t yourself a subscriber, my pump just shit itself today but now I am confident I can fix it

  • @dp2698
    @dp2698 Рік тому +1

    thank u so much brother, saved me some money

  • @adrianwhittlestone71
    @adrianwhittlestone71 Рік тому

    Cheers buddy 👌😎 informative and a job now for the VX 😬

  • @davegunner8642
    @davegunner8642 Рік тому

    Great Vid,excellent job

  • @amrahimi
    @amrahimi Рік тому

    Good work mate

  • @tonyellis9616
    @tonyellis9616 Рік тому

    Thanks a lot.

  • @coreyaylward3428
    @coreyaylward3428 Рік тому

    Having trouble with mine at the moment... will take the coolant but chug it straight out..
    Had a cut up 2l coke bottle for purging air.. literlay goes from quarter of the bottle then chugs it then spits out like half a litre and just continues to do that..

  • @ColinPearce-nr6lp
    @ColinPearce-nr6lp 6 місяців тому

    Did you retighten the four bolts on the pulley?

    • @-RossTheBoss
      @-RossTheBoss  6 місяців тому

      Yes you need to tighten them back up

  • @scotthoward4836
    @scotthoward4836 7 місяців тому

    Question sir. How did you get engine temp to come up on the dash? I have a 2002 VY

    • @braydonhallows8118
      @braydonhallows8118 7 місяців тому

      Hold the mode and up (or down) on the left hand side whilst car is In accessory before starting and then wait for beep. Then start

  • @unfknknown9678
    @unfknknown9678 Рік тому

    Hopefully this fixes my vy overheating 😂

  • @tommoderitz1077
    @tommoderitz1077 Рік тому

    Hey mate is it necessary to be using a rattle gun to do those bolts back up, do they need to tourqued to a certain level? or will I be sweet just using socket set? Cheers for the video heaps helpful!

    • @-RossTheBoss
      @-RossTheBoss  Рік тому +1

      There probably is a torque setting. But a socket should be fine. I don't have a torque wrench and I've never had any issues.

    • @tommoderitz1077
      @tommoderitz1077 Рік тому

      @@-RossTheBoss cheers 🤙🏼

  • @scottrussell7659
    @scottrussell7659 9 місяців тому

    Where are you located mate?

  • @ozwasp
    @ozwasp Місяць тому

    Don't forget the nuts are imperial, not metric

  • @thedavesofourlives1
    @thedavesofourlives1 Рік тому +1

    a rear wheel drive 3800, that's new

    • @-RossTheBoss
      @-RossTheBoss  Рік тому +4

      Here in Australia we've had the RWD 3800 V6 since 1988. First introduced in our Holden VN Commodore

  • @killerkiwi8580
    @killerkiwi8580 Рік тому

    what is the brown stuff my vx has the same thing

    • @-RossTheBoss
      @-RossTheBoss  Рік тому +3

      Hi, the cause is usually the lower intake manifold (Valley Gaskit) slowly leaking oil into your coolant. This is fairly common on the V6 commodore motors

    • @killerkiwi8580
      @killerkiwi8580 Рік тому

      @@-RossTheBoss cheers man thanks keep up the good work

    • @ramennoodleboi3341
      @ramennoodleboi3341 10 місяців тому

      @@-RossTheBossdoes this leak cause any problems and need fixing or would I be sweet to leave it? Cheers for the vid btw

  • @danielmillard8134
    @danielmillard8134 3 місяці тому

    You just gained 10RWKW doing that yourself