Sir aaap ko rock bottom basic level se - high level Tak ka perfect knowledge hai and specialist of all SMPS circuit Apki sab video without any time waste perfect aur simple hai. I am very very impressed by you ,,👍
Sir, today again i was watching this video,wow what a clear explanation,and perfect testing of transformer of microvave. and your videoes are very useful for everyone,who is dealt with electronic knowledge, you are awasome sir,app dilsey sikhate, with safety 😊a lots of respect and thankyou very very much ❤
Hello, for measuring the secondary of the transformer with the 2M and 2K resistance bridge, what kind of resistance do you use? (carbon, metal film, metal oxide?)
Assalamualaikum sir.I have one sharp microwave oven. I check the ohms value of HV terminal with body.it shows 75.4ohms.rest of the values are matching with your video.If so,is it considered good or bad.please clear my doubt
HV transformer's (high voltage winding) one end is connected to oven body and the second end goes to HV diode and capacitor if you are getting reading with HV terminal and oven's body. that is good indication that the winding's second side is making good connection
sir ,i made this kit exactly according to the diagram,with same resistors and thier wattage, but when i tested it,i tested it for 4 seconds,and my new multimeter got blown,thanks it was a cheap clampmeter.sir whats the reason ,can you explain it sir?
I've noticed about 3.5vac at magnetron connection, can't i use a transformer whose output 3.5vac and feed it to the magnetron in that position of the microwave for testing for the heat
3.5vac is the low side voltage used for the vacuum tube filament inside the magnetron. But 1,800 to 2,800 volts is the high side voltage needed for the magnetron to heat.
very good explanations 👍👋😉
thanks a lot dear friend
stay blessed
❤@@HaseebElectronics1
Sir aaap ko rock bottom basic level se - high level Tak ka perfect knowledge hai and specialist of all SMPS circuit
Apki sab video without any time waste perfect aur simple hai.
I am very very impressed by you ,,👍
روعة الله يعطيك العافية استاذنا الفاضل أشرف على معلوماتك القيمة وجعله في ميزان حسناتكم استاذنا ❤❤❤❤❤
الحمد للہ
Sir, today again i was watching this video,wow what a clear explanation,and perfect testing of transformer of microvave. and your videoes are very useful for everyone,who is dealt with electronic knowledge, you are awasome sir,app dilsey sikhate, with safety 😊a lots of respect and thankyou very very much ❤
Very good explanation and schematic!!! Thank you.
You are welcome!
Super testing high voltage, cold checking is good,I think, resistance checking is not dangerous 😊 sir, thankyou
yes resistance test is safe
but this live test provides an accurate health status of the transformer
Muy buena explicacion Gracias
اسلام وعلیکم بھائی اسکی جگہ سوئچ موڈ پاور سپلائی لگا سکتے ہیں ؟ اسکی پاور سپلائی بنانا سیکھائیں
AoA Sir need your help
Make a video on NCP1200,what is Dynamic self supply how it generates Vcc for itself.. I am facing an issue in it
Very nice explained sir!
Thanks and welcome
Hello, for measuring the secondary of the transformer with the 2M and 2K resistance bridge, what kind of resistance do you use? (carbon, metal film, metal oxide?)
Very explanatory, thank you.
Excellent demostration!! thanks a lot...got a like!!
best regards
such a good explanation👏
Assalamualaikum sir.I have one sharp microwave oven. I check the ohms value of HV terminal with body.it shows 75.4ohms.rest of the values are matching with your video.If so,is it considered good or bad.please clear my doubt
HV transformer's (high voltage winding) one end is connected to oven body and the second end goes to HV diode and capacitor
if you are getting reading with HV terminal and oven's body. that is good indication that the winding's second side is making good connection
Veery good explanation.❤❤❤❤
Very useful information thanks
So nice of you
You are fantastic.
I take alot of information from your videos .
Thanks alot .
most welcome dear brother
it is my pleasure
@@HaseebElectronics thank you 🙏..
I wish to explain the how can we check the ic electronic on the board
Salam sir. Can you share a circuit diagram to measure high voltge side of a microwave oven transformer. Because i want to make a circuit also.
Excellent sharing brother.
Many many thanks
thank u for this video
sir ,i made this kit exactly according to the diagram,with same resistors and thier wattage, but when i tested it,i tested it for 4 seconds,and my new multimeter got blown,thanks it was a cheap clampmeter.sir whats the reason ,can you explain it sir?
Good teaching
Very good video
best regards
Good job Bhai
thanks a lot dear sister
Transform readings all OK but sparking and blasting, magnetron reading OK, capacitor reading OK, diode not short. How test?
Nice information
it is my pleasure
if primary winding resistance is showing 6ohms and hv winding resistance is 212ohms than what is the condition of the transformer
Thanks sir ji....
Welcome
Weldon keep sharing
it is my pleasure
I've noticed about 3.5vac at magnetron connection, can't i use a transformer whose output 3.5vac and feed it to the magnetron in that position of the microwave for testing for the heat
3.5vac is the low side voltage used for the vacuum tube filament inside the magnetron. But 1,800 to 2,800 volts is the high side voltage needed for the magnetron to heat.
👌👌👌👍
Price kaya ha transfor ka
Thanks sir ji....