Breaking Down Plywood with
Вставка
- Опубліковано 29 лис 2024
- Need help getting started with breaking down plywood and making rip cuts? Want to learn some tips and tricks to improve your skills? Follow along with Jason Bent as he walks through breaking down plywood step by step!
Materials and tools used:
FS Guide Rails
TSC 55 Track saw
Parallel Side Fence FS-PA
MFT/3 Table Set
Accessory Kit SYS3 M 137 FS/2 (included in MFT/3 Set)
For more by Jason Bent:
UA-cam: @bentswoodworking
IG: / bentswoodworking
Website: www.bentswoodw...
Built Better to Build Better
Disclaimer: Festool USA retains the right to remove profane, abusive, trolling, or spam comments at our sole discretion.
Festool USA Website: bit.ly/3fVZrmg
Festool USA Service: bit.ly/37YhVQn
Festool USA Dealers: bit.ly/2NtBTsH
Instagram: bit.ly/3i1lgmf
Facebook: bit.ly/3fV1jvu
LinkedIn: bit.ly/2VidKJY
Festool Sedge: bit.ly/2CZXbfB
I love that you're teaching for Festool. Huge fan of your calm, direct approach and I love your main channel. Congratulations Jason - well deserved!
Glad you enjoy it!
As the age of sedge comes to it's twilight, a new dawn arises with Bent's "Festool" woodworking.
You are a great teacher. It comes through in every video.
Thanks Jason. You represent Festool well. Looking for ward to more video's. Cheers from Canada.
Thanks for a calm no hype explaination! You helped me a lot with this! Proof you don't have to have a circus to put on a good show.... lol Great video!!!
Glad it helped!
Thanks Jason. Always helpful. I used the MFT and my parallel guides to build my first two cabinets. BUT… I built one. Then built the second. The great thing is that because the Festool tools are so accurate…. They are the same. But it would have went so much faster if I had done it this way. About to build some more. Definitely going to do this.
That is awesome!
Thanks Jason!
Was this off by a 1/16 of an inch or is that accurate enough? Or just the camera angle didn’t capture the cuts well? That is about 1.6mm off. I normally find using a parallel guide and a quad hinge system to give me accuracy that tape measures can’t detect. Just wondering why things are off slightly. If my calculations are right, the angle is off by 0.1°, I am guessing parallel clamps are not calibrated properly. Over an 8ft rip cut, this would create an error of 4.2mm assuming the pieces cut were 3ft long.
If the error is caused by the hinge system, measurements will differ.
If the error is caused by both the parallel guide and hinge system, the measurements will differ again and be the error be smaller.
The question which should be talked about, because newer woodworkers would get bogged down with these details is accuracy vs consistency? As long as the errors are good enough, the project will be good enough. If accuracy is required, calibration of the track saw on the track, the blade, the toe, the hinge to fence, parallel guides all have to be meticulously checked and taken care of. Rechecked every few cuts.
Nice shirt!!! Awesome job sir.
Thanks!
i love Festool.
Go Jason!!!
Well said.
I still prefer TSO parallel guides :)
As much as I love my Festool products, I have to agree the TSO parallel guides are better. Festool needs to sell a retrofit kit for their parallel guides to support the tippy legs or modify the connectors to allow the legs to rest ON the sheet. Both TSO and Woodpeckers parallel guides do that. I wish my Festool parallel guides did it, too.
Must be nice to have Festool sending you all of their expensive products for free.
Bent works at Festool now?! 😆 Was a little jarring seeing one of my favorite UA-camrs on Festool's channel - suddenly getting the sense that the woodworking community is a lot smaller than I'd realized. LOL
Why are you surprised by this? Have you not seen his workshop?
No he was just interning for a bit
😂 Jason Bent was actually working with us last year, and this is some content we did together! He’s a great friend and partner with Festool 🙂
What guide rails did you use? One 2700 or 2 1400’s?
Rip/Cross cuts on plywood that have alternating grains?
After taking a Festool training class I started cutting this way. My issue is with accurately setting the parallel guides. How do you make both sides match by eye?
I slide them together (while they’re on the rail) so I can make sure they’re in sync. If they feel flush then they’re quite accurate. Hope that helps 😊
almost didnt recognice him without his cap om :))
This is a greatly helpful video. But don’t have all the tools shown here.. so have to slowly build up my collection :)
Glad it was helpful!
Smooth is fast
I wrap the vac hose around my arm the same way 😂