Tesla coil : How to make Tecla coil using Tip41c transistor
Вставка
- Опубліковано 25 гру 2020
- Tesla coil : How to make Tecla coil using Tip41c transistor
My other videos about high voltage
• High voltage transform... high voltage transformer
• Jacob's Ladder : How t... jacob's ladder
• Tesla coil : how to ma... tesla coil
• Tesla coil : how to ma... tesla coil
• ZVS driver : how to ma... zvs driver
• High voltage capacitor high voltage capacitor
• Simple High voltage : ... high voltage with 555 timer
• ZVS Driver : How to ma... ZVS Driver(version 2)
• Tesla Coil : How to ma... spark gap Tesla coil
Nice job
Good job
Nice work
❤️ staggering
Nice
Boa tarde professor
👌👌👌
Good
bro my tesla coil is not working ,I made it same as shown in the video ,600 turns with 28 gauge wire in secondary and primary of 2 and a half turns with thick 1 mm copper wire with tip41c transistor and 1k resistor in parellel and powerd it with a 12v 2amp adapter . I also change the primary connection too but it does not work . All connections are good with proper solder with very clean setup , please help me .
The transistor must be the fault I had the same problem , but after changing the transistor it worked
Use a higher resistance more than 3k ohm. I also used it and it and worked. You should also use capacitor ,it's necessary
you are right but I want ask can your tesla coil run on 1 or 1 and a half turn or less than 1 .If it work so that I will get a idea what should be the turn ratio of secondary and primary and if I use tip31c transistor IT will be ok.
I tested this tesla coil with 1 and 1.5 turns of primary coil but it didn't work with less than 1.5 turns. And you can get good result with 1.5 turn of primary coil and 1200 turns of secondary coil. You can use tip31c but if you use tip41c your tesla coil will be stronger.
@@mx3239 bro which wire you used in primary coil
Hello my friend, greetings, could you tell me what was the current used to feed the circuit? And what was the power used in the resistor?
Is both slayer exciter and mosfet tesla coil work same and which tesla coil lowest power input and produce arcs and has the longest range to light CFL bulbs.
In tesla coils the input voltage is so important. And they don't have much different in lower voltages. But the mosfet tesla coil use for higher voltages like 220v. I suggest you use this circuit because it is easier to make and there is no different between this and tesla coil using mosfet in low voltage.
What amphire do you input to this
Sir, both Primary & Secondary coils need to be same direction? CW or CCW?
It matters yes if you try it and it doesn't work flip Ur secondary coil then try again if it still doesn't work check your connections with every thing and if it still doesn't work make sure your power supply is outputing 12v and not current limited
sir now I have made a secondary coil with 1250 turns and 2 and a half turn in primary ,now there will be any arcs if I power it with a 9v battery.
I think you can get som arcs with this coil. and it will be better if you change the primary coil to 1.5 turns.
@@mx3239 bro plz help me its urgent need help in tesla coil
Can I use a 223j 2kv capacitor
sir how
many turns are there in secondary coil and primary coil.I have subscribed your channel .
Thanks❤❤. secondary coil is 600 turns and primary coil is 2 turns
Can I use several like 6. 1uf 105j 400v capacitor in parallel. Input 24 volt 10amp will it give me big spark
Yes you can use several capacitor. But TIP41C will burn if you run it with 24 volt 10 amp. If you wanna try it with 24 volt 10amp it's better to use 13007 or 13009 transistor . ( 13007 is better for lower voltages)
@@mx3239 but I am using 8 tip31c transistor in parallel
@@meenawagh6877 I thing tip41c are not rated for 10amp
sir can I run it with 9v and will there be any arcs
You can run it with 9v and it can turn on the lamp but I didn't get any arcs with 9v ( but if you close your finger to the coil you can feel something)
Very good, but how much amp
Sir i have made secondary coil in diameter 3 inch and height 13 inch 900 rounds and primary coil with 6 rounds if I power it with 2 9volt batteries in parallel it will become 18 volts after that it will work or not please reply me. Any spark will produce or not?? . Please help me. I am in urgent. There is science exhibition in our school so please reply me very soon sir 🙏🙏
What's the function of capacitor over there???
Bhai... To release the power in shorts bursts... (Thousands of bursts in a second... Increasing the voltae through the coil creating more high voltage and spark)
@@abrokanfxr3388 thank you bhai ❤️
Can you share circuit?
Can i use 105j 400v instead of 474j 400v
Yes you can use 105j capacitor ❤❤
@@mx3239 tnx bro its working perfectly ❤️❤️❤️
❤❤
Good, voltage?
I ran it with 12V ❤❤
Bro plz can you help me
👌👌👌