Відео

Resistors in parallel right?

sir Please give The code of this project

Boa tarde professor

ایرانی هستی داش ؟

Hello my friend, greetings, could you tell me what was the current used to feed the circuit? And what was the power used in the resistor?

Very good, but how much amp

What amphire do you input to this

Sir i have made secondary coil in diameter 3 inch and height 13 inch 900 rounds and primary coil with 6 rounds if I power it with 2 9volt batteries in parallel it will become 18 volts after that it will work or not please reply me. Any spark will produce or not?? . Please help me. I am in urgent. There is science exhibition in our school so please reply me very soon sir 🙏🙏

Una pregunta, cuanta vuelta tiene la bobina secundaria?

How did you avoid the servo motor interference with the IR? I can't get past that!

Sir can you give the name of the transister and, will this shorly work .

What's the function of capacitor over there???

Bro plz can you help me

Sir, can i use 13009 transistor

Can I use a 223j 2kv capacitor

Hello, please tell me the amount of capacitor, thank you

Can I use 25n120 MOSFET for this circuit and any other diode

Nice try

Good

very good work !

would 2 1.5k resistors work or even maybe two .22k in series ? update... well no go tried the two .22k ohm resistors in series and couldnt get close to 12v until cranking amps up past 3 at which point the wire i used to connect the middle pin to the secondary coil(oops meant primary apparently) melted its solder off disconnecting itself from the transistor. If I was trying to heat up the transistor and heatsink tho then that was a success lol

ua-cam.com/video/SChgc0QJlCc/v-deo.html

Will the circuit work without the ceramic capacitor???

Doesn't work 😢😢

Sir, both Primary & Secondary coils need to be same direction? CW or CCW?

Can i use irfzn44 ? Instead

Can i use 22nf 2000v capacitor

Tôi chỉ quấn được 100vòng có được không

60v is minumum voltage required to perform this project?

finally a tesla coil with a bipolar transistor. note: where do you connect the positive and the negative? And what is the maximum and minimum rating? Please answer me😢🙏

Good, voltage?

Nice job

Soon you will get 1M subscribers

Perfect

How much volts, amps do you put in?

Have you used D13005ED

You need to use thicker wires bro im using 12v but i get way higher Voltage and current arcs than that

You got a new subscriber

Hey nice I gonna make this

Can you share circuit?

My slow brain read the title as 13009 transistors. Like you chained 13009 of them together. Wow.

Can I use several like 6. 1uf 105j 400v capacitor in parallel. Input 24 volt 10amp will it give me big spark

This music triggers me lol

Nice work👍

can it make arcs

Can i use 13007 transistor ? And can i remove the adjustable switch? If i can then how

Can you please explain me more where do i connect + and - terminals

Nice job

//We'll start by adding our libraries #include <LiquidCrystal.h> #include <SimpleDHT.h> //Declaring digital pin no 6 as the dht11 data pin int pinDHT11 = 6; SimpleDHT11 dht11; //Declaring the lcd pins const int rs = 12, en = 11, d4 = 5, d5 = 4, d6 = 3, d7 = 2; LiquidCrystal lcd(rs, en, d4, d5, d6, d7); void setup() { // Don't forget to choose 9600 at the port screen Serial.begin(9600); //Telling our lcd to start up lcd.begin(16, 2); } void loop() { //These serial codes are for getting readings on the port screen aswell as the LCD display, since they'll offer us a more detailed interface Serial.println("================================="); Serial.println("DHT11 readings..."); byte temperature = 0; byte humidity = 0; int err = SimpleDHTErrSuccess; //This bit will tell our Arduino what to do if there is some sort of an error at getting readings from our sensor if ((err = dht11.read(pinDHT11, &temperature, &humidity, NULL)) != SimpleDHTErrSuccess) { Serial.print("No reading , err="); Serial.println(err);delay(1000); return; } Serial.print("Readings: "); Serial.print((int)temperature); Serial.print(" Celcius, "); Serial.print((int)humidity); Serial.println(" %"); //Telling our lcd to refresh itself every 0.75 seconds lcd.clear(); //Choosing the first line and row lcd.setCursor(0,0); //Typing Temp: to the first line starting from the first row lcd.print("Temp: "); //Typing the temperature readings after "Temp: " lcd.print((int)temperature); //Choosing the second line and first row lcd.setCursor(0,1); //Typing Humidity(%): to the second line starting from the first row lcd.print("Humidity(%): "); //Typing the humidity readings after "Humidity(%): " lcd.print((int)humidity); delay(750); }

int soundSensor=2; int LED=4; boolean LEDStatus=false; void setup() { pinMode(soundSensor,INPUT); pinMode(LED,OUTPUT); } void loop() { int SensorData=digitalRead(soundSensor); if(SensorData==1){ if(LEDStatus==false){ LEDStatus=true; digitalWrite(LED,HIGH); } else{ LEDStatus=false; digitalWrite(LED,LOW); } } }