Well it's 2024 and I have had two of these for at least a year and I remember I had some kind of problem and gave up. I just revisited them today and already have one working... now that's results and although the Arduino IDE menus have changed a little still was able to get things up and running in no time... I was skeptical until BOOM there it was! Thanks!! Onto number 2...
Holy shit, I fucking LOVE you man, I've had issues with connecting the camera to the esp32 physically, yours is the only video I've found that shows how to do it,
I'm amazed, it actually worked. Thanks man 🐱 I did have one issue with using a charge only cable at first, but switching to a data version allowed the upload 👍
I was following everything step by step but in Serial Monitor i'm receiving this error: E (468) camera: Camera probe failed with error 0x105(ESP_ERR_NOT_FOUND) Camera init failed with error 0x105
Thanks for the quick start walkthrough! Question - once the ESP32-CAM is programmed, do you still need the ESP32-CAM-MB attached, or can you just provide a power source to the Camera module?
I think something is wrong with my audio because all I'm getting is birds pooping in the background. It is hard to read and watch a video at the same time.
My device manager is not changing when I am connecting the device. After following all the procedures I am getting error messages Status 1 or 2 that either the esptool is not connected or hardware or driver issue Pls help
hey sir, when I got the ip cam, and opened it in my browser I got the error "this site can't be reached 192...(my ip cam) took too long to respond. Try: checking the connection check proxy and firewall run windows network diagnostic please help me
Problem with this particular USB programmer module is that it uses up all the available pins from the ESP32 cam, so you cannot use them for other projects that could use the GPIO. Do you have any solutions/suggestions for that?
I haven't tried by myself, but I have seen that once you have programmed the module you can disconnect the usb shield and just give power supply to the pins of module. You are ready to use other pins....
great totorial, i ran across a small problem though, mine never provides an ip address to view the camera, it just says "Serial.print("Camera Ready! Use '"); Serial.print(WiFi.localIP()); Serial.println("' to connect");" But shows WiFi connected. Scanned my network for the camera, think i found it, but no camera picture. any suggestions?
has anyone ever encountered the "Camera init failed with error 0x105" issue while using ESP32 CAM? I have changed several modules, but the same error persists
Hi, i follow exactly what you do and what component you use in this tutorial. But I'm keep getting error message "A fatal error occurred: Failed to connect to ESP32: Timed out waiting for packet header". I don't know how to solve it, can you help me?
@@AtlantaTerry After pressing upload, when it shows connecting immediately press reset button which is spotted at left side of sd card slot then code will upload
all has same but i not understand were i found my raspberry pi 4 SSID and password. i not understand ,i not can add wifi printer to raspberry and win19 computer were have wifi usb dongle, and android phone, i not know how connected, router have usb and wifi bridge sim card can go to internet, raspi go internet ok and whit wifi win10 go internet. but what have SSID and password. were, second problem if selecter ai thinker boar load has all error lot, but if select board esp32 no errors. totally same boars wifi box have write esp-32S. and serial monitor NOT come ip addres only lot text but no ip.
thanks, working well now, i need only follow this manual and make all many time new and one time go working good. lag lot whit raspberry pi4 computer but working. next need test how working whit win10 base too.
hello nice video. I have a one problem how i can fix this one A fatal error occurred: MD5 of file does not match data in flash! Failed uploading: uploading error: exit status 2 im new in this .Thanks
تمام جزاك الله خير ما بدك تحط اغاني! بس يا اخي الصوت مزعج ومقرف لأبعد الحدود. في أصوات افضل من هيك! صراحة تركت المقطع بسبب صوت المي الخرا والعصفور اللي يعيد كل 4 ثواني!!
*[SOLVED] ESP32CAM Error - Failed to connect to ESP32 Cam || Problems Uploading Code to ESP32 Camera*
ua-cam.com/video/lqNRj4kQCcA/v-deo.html
Well it's 2024 and I have had two of these for at least a year and I remember I had some kind of problem and gave up. I just revisited them today and already have one working... now that's results and although the Arduino IDE menus have changed a little still was able to get things up and running in no time... I was skeptical until BOOM there it was! Thanks!! Onto number 2...
Holy shit, I fucking LOVE you man, I've had issues with connecting the camera to the esp32 physically, yours is the only video I've found that shows how to do it,
I'm amazed, it actually worked. Thanks man 🐱 I did have one issue with using a charge only cable at first, but switching to a data version allowed the upload 👍
Face detection doesn't seem to work yet
A fatal error occurred: Failed to connect to ESP32: No serial data received.
ErrESP32
You may need a driver.
Bro can you help same error
First install DRIVER for CH340 chip to communicate with board
I was following everything step by step but in Serial Monitor i'm receiving this error:
E (468) camera: Camera probe failed with error 0x105(ESP_ERR_NOT_FOUND)
Camera init failed with error 0x105
THANK YOU SO MUCH!! This was the only tutorial that worked for us! You're a lifesaver!
Thank you - I get right to the point of reset assume on ESP32-CAM-MB but no luck in reading serial link to find IP address
got it working changed baud rate :) da thanks you are amazing
@@mikekennedy7999 Must be 115200 i think
Hello, my serial monitor shows that. Are there any drivers missing here?
....ets Jul 29 2019 12:21:46
rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:1
load:0x3fff0030,len:1344
load:0x40078000,len:13964
load:0x40080400,len:3600
entry 0x400805f0
can you please help?
For me also same problem
Did you solved it?
hi how do i fix, esp_core_dump: No core dump partition found on serial monitor after reseting the esp 32 mb
try use the arduino IDE 1.8
I have the same issue
It says error no core dump partition found what should i do??
same idk how to fix it :(
Thanks for the quick start walkthrough! Question - once the ESP32-CAM is programmed, do you still need the ESP32-CAM-MB attached, or can you just provide a power source to the Camera module?
You can provide power from external sources
I think something is wrong with my audio because all I'm getting is birds pooping in the background. It is hard to read and watch a video at the same time.
If you are using ESP32-CAM-MB, do you not need to short the gnd
thank you! Thanks to your video, I was able to solve the problem and make it a success.
Me : let's do this
After reading comments 💀
Hello, is it possible to also add a sensor for example on some pins when using ESP32-CAM-MB ?Thanks
Big Thank you for this video and a new follower.
thanks man your are the only great
👏
I tried this video and it worked. If I unplug my esp and then reconnect it,does my IP Address change?
After clicking preferences I'm not getting additional boards, 🤷♂️what am I doing wrong? Thanks in advance
My device manager is not changing when I am connecting the device.
After following all the procedures I am getting error messages Status 1 or 2 that either the esptool is not connected or hardware or driver issue
Pls help
hey sir, when I got the ip cam, and opened it in my browser I got the error "this site can't be reached 192...(my ip cam) took too long to respond.
Try:
checking the connection
check proxy and firewall
run windows network diagnostic
please help me
Problem with this particular USB programmer module is that it uses up all the available pins from the ESP32 cam, so you cannot use them for other projects that could use the GPIO. Do you have any solutions/suggestions for that?
I just use this to program the board.
still learning not a pro, but you could use a breadboard or connect some of the pins with wires to a arduino
I haven't tried by myself, but I have seen that once you have programmed the module you can disconnect the usb shield and just give power supply to the pins of module. You are ready to use other pins....
thank you it works very good
You're welcome!
@@YellowPurple thank you
great totorial, i ran across a small problem though, mine never provides an ip address to view the camera, it just says "Serial.print("Camera Ready! Use '");
Serial.print(WiFi.localIP());
Serial.println("' to connect");"
But shows WiFi connected. Scanned my network for the camera, think i found it, but no camera picture. any suggestions?
has anyone ever encountered the "Camera init failed with error 0x105" issue while using ESP32 CAM?
I have changed several modules, but the same error persists
Hi, i follow exactly what you do and what component you use in this tutorial. But I'm keep getting error message "A fatal error occurred: Failed to connect to ESP32: Timed out waiting for packet header". I don't know how to solve it, can you help me?
You may need a driver.
@@AtlantaTerry After pressing upload, when it shows connecting immediately press reset button which is spotted at left side of sd card slot then code will upload
@@koti_official_2005Bro please help me I am not even able to start it
@@itsshiv287 What exact problem are you facing?
After flashing when I press serial monitor it only shows these different symbols no actual link address. Pls help. Thanks in advance
Nice info, thanks :)
Hallo, arduino IDE 1.8.19 findet im Board Manager...esp32 by Espressif Sytem...nicht? Hast du einen Tip?
thanks man worked fine
i have question my esp32 cam after following your instruction still now working please help me
excellent tutorial
can you help if i click on RST it not give IPAddress
in serial monitor > top right
set baud to 115200
Error compiling for board Ai Thinker esp32-cm
how can you secure the camera with a password? At the current state it is a vulnerability to the home network.
thank you!
what should i do if it don't have com5. it only has com1 and com3
Use com 3
Bhai jab mai code upload karta huun too ip adress nahi atta
(Camera probe not found 0x105 error)ye error aa raha hai
Is ka solution bata doo please
assalamualaikum sir i directly follow ur instruction but when i open the serial monitor it show different in ur video please help me sir
Make sure to select "New Line" and "115200 baud" Only layout changed
all has same but i not understand were i found my raspberry pi 4 SSID and password. i not understand ,i not can add wifi printer to raspberry and win19 computer were have wifi usb dongle, and android phone, i not know how connected, router have usb and wifi bridge sim card can go to internet, raspi go internet ok and whit wifi win10 go internet. but what have SSID and password. were, second problem if selecter ai thinker boar load has all error lot, but if select board esp32 no errors. totally same boars wifi box have write esp-32S. and serial monitor NOT come ip addres only lot text but no ip.
thanks, working well now, i need only follow this manual and make all many time new and one time go working good. lag lot whit raspberry pi4 computer but working. next need test how working whit win10 base too.
mode:DIO, clock div:1
load:0x3fff0030,len:1448
load:0x40078000,len:14844
ho 0 tail 12 room 4
load:0x40080400,len:4
load:0x40080404,len:3356
entry 0x4008059c
E (337) esp_cor��&VW }���͡: No core dump partition found!
E (337) esp_core_dump_flash: No core dump partition found!
hello nice video. I have a one problem how i can fix this one
A fatal error occurred: MD5 of file does not match data in flash!
Failed uploading: uploading error: exit status 2
im new in this .Thanks
Hi,do you prvide freelace services,i need your help in one of our servcies
Thank you
Thanks
THANK U
good video thank you
Fatal error occurred failed tu connect to esp 32
welcome to the jungle
why i got fatal error allocation.h
It worked for my first try, second try on a different network would not work
E(493) esp_core_dump_flash: no core dump partition found
same, do you find any solution for that?
nice
تمام جزاك الله خير ما بدك تحط اغاني!
بس يا اخي الصوت مزعج ومقرف لأبعد الحدود.
في أصوات افضل من هيك!
صراحة تركت المقطع بسبب صوت المي الخرا والعصفور اللي يعيد كل 4 ثواني!!
I have face fatal problem bro please help me
O yar mne kia kr lia..yahi camera le lia😢😢😢😢
+
rst:0x1 (POWERON_RESET),boot:0x3 (DOWNLOAD_BOOT(UART0/UART1/SDIO_REI_REO_V2))
waiting for download
Press reset button and wait for wifi connection. BY THIS, DO IT SEVERAL TIMES
@@YellowPurple i need esp 32 cam
@@YellowPurple i do it but not solve
@@YellowPurple Not the reset. you should press IO0
Great tutorial
merhaba arduino Mikro USB Programlayıcı görmüyor seri portlar /dev/cu.usbmodem641 adresindeki kart kullanılamıyor no kart