I just saw your build. Looks great. My project went into a dead end too. 1st one of my rockers both broke after I replace it it wouldn’t run and noticed low compression. I send it to Toyan after a long wait it seems like they didn’t do anything but made it worse. When I finally had time to try to finish it the driveshaft broke at the rear end where the nut tightens up the flywheel. Been more then a year now and waiting to see what Toyan is going to do. Lol I only had the change to made the engine run video on the future chassis then came to a halt. Good luck fixing it.
Yup, sucks badly. What pisses me and I’m sure lots others is that they don’t work with you 💯 percent BUT they are so fast in pushing sales on new items without Quality control.
I wanna hear/see these motors tuned in addition to having proper exhaust pipes. Did this motor undergo a propper break in procedure before it being installed in the ran and ran?
So gos from battery, manual on off switch,to pwm switch which runs a y plug to the Toyan starter unit which has one glow driver,other side of Y gos to stand alone glow driver
I just got my fs-l200 to start and I really want to make an RC car with it but I don't know where to start. Whenever I look online for a specific chassis that someone uses like the one you have I have no luck. I'm also afraid that if I get a chassis without having a youtube video on it I won't be able to figure it out and waste my money. I hope you know either a place to buy chassis or a tutorial that is made for people who are just getting into nitro rc cars.
Don't believe if anything can buy off shelf that it will fit straight into,Hence why only be finding custom built chassis Best thing be picking up a used nitro touring car to give you all bits going to need and modify to suit
I tend to pickup good used cars from Facebook marketplace,since I know will only tear apart,This car was made up from two cars and a few other new parts
get and HG p407. Its the easiest build. Pair that up with either a tmaxx trans(single, forward only gearing) or a revo 3.3 transmission. To make it 4wd use a crawler transfer case. That was my first of many builds. Having a 3d printer really helped too
Was a new engine being run slow to break in,but also turns out was a faulty part on flywheel which failed so was spinning on shaft, meaning crank was damaged beyond repair,been sitting in bits ever since need to find time to rebuild
cool
I just saw your build. Looks great. My project went into a dead end too. 1st one of my rockers both broke after I replace it it wouldn’t run and noticed low compression. I send it to Toyan after a long wait it seems like they didn’t do anything but made it worse. When I finally had time to try to finish it the driveshaft broke at the rear end where the nut tightens up the flywheel. Been more then a year now and waiting to see what Toyan is going to do. Lol I only had the change to made the engine run video on the future chassis then came to a halt. Good luck fixing it.
Got replacement parts on way,managed to remove seals and bearings off crank without damaging now to wait for it to arrive
my crank broke at the nut brand new as i tightened it ,,,,never ran a lick had to buy a new crank
Yup, sucks badly. What pisses me and I’m sure lots others is that they don’t work with you 💯 percent BUT they are so fast in pushing sales on new items without Quality control.
I wanna hear/see these motors tuned in addition to having proper exhaust pipes. Did this motor undergo a propper break in procedure before it being installed in the ran and ran?
Custom exhaust on cards,
Was broken in for a full tank on bench before running in video,
Need to find time to get back to putting together...
@@RevXSCustoms Okay sweet! And I wish I remember what I was trying to say in the end of my previous comment 😅
So how do you do wires off the starter motor >esc>glow igniter>battery? Or starter motor>glow igniter>esc>battery? Thanks
So gos from battery, manual on off switch,to pwm switch which runs a y plug to the Toyan starter unit which has one glow driver,other side of Y gos to stand alone glow driver
I just got my fs-l200 to start and I really want to make an RC car with it but I don't know where to start. Whenever I look online for a specific chassis that someone uses like the one you have I have no luck. I'm also afraid that if I get a chassis without having a youtube video on it I won't be able to figure it out and waste my money. I hope you know either a place to buy chassis or a tutorial that is made for people who are just getting into nitro rc cars.
Don't believe if anything can buy off shelf that it will fit straight into,Hence why only be finding custom built chassis
Best thing be picking up a used nitro touring car to give you all bits going to need and modify to suit
@@RevXSCustoms I really appreciate that you even responded at all. Would the best place to buy them be ebay or are there better websites.
I tend to pickup good used cars from Facebook marketplace,since I know will only tear apart,This car was made up from two cars and a few other new parts
@@RevXSCustoms Thank you!
get and HG p407. Its the easiest build. Pair that up with either a tmaxx trans(single, forward only gearing) or a revo 3.3 transmission. To make it 4wd use a crawler transfer case. That was my first of many builds. Having a 3d printer really helped too
All that noise and no spied
Was a new engine being run slow to break in,but also turns out was a faulty part on flywheel which failed so was spinning on shaft, meaning crank was damaged beyond repair,been sitting in bits ever since need to find time to rebuild
Italiano
All these toyan engines are so cool but it’s just such a let down when I see them in a RC car… just gutless and heavy!
More of a waste sitting on a bench and not in a build