LED One Color Remote Control Programming
Вставка
- Опубліковано 24 чер 2017
- I cover Programming multiple Inline RF Remote Control Dimmer Switches for LED Strip Lights (one color / Single Color) to work simultaneously in close proximity to control multiple individual light sets.
See how this same key command that can help you, can also wipe out all the work you have done.
There are no programming instructions provided with the remote. This is the technique I have found for this model.
We will also show the hazards of a short and how these LED RF remote controls can create a short and potential fire hazard.
This programming applies to just remotes with this keyboard layout... other keyboard layouts may use different key combinations
These are rated for 12-24V. Labeled to support 12 Amps with instructions that say they support 6 Amps. - Навчання та стиль
You are the man! Thank you so much for this tutorial! I have looked for this solution everywhere. I called manufacturers, wholesalers etc. None knew this trick. A++ thanks!
THANK YOU SOOOOO MUCH !!!!! My kids were driving me crazy and no one knew the answer to this. They each have a set in their rooms....its been a constant battle !!!!!
I though my controller had given up on me on the first minutes. Thanks for the programming tip, + and - keys pressed together worked like a charm in getting my controller to respond to the rf remote again. Thanks!
They really should have included this in the booklet! Thank you sir.
Thank you a lot!!
I have 5 LED strips in different floors and they turn on / off all together!!
You save me!!😊😊
Great news. I still use many of these around the house and with new installs when I don’t use a motion sensor. I have recently started playing with WiFi enabled single color and multi color controllers. The cost is more per unit. You gain scheduling, control from multiple devices and smart home integration like google and Alexa for those areas where hands free is of benefit. Enjoy your install.
OMG Thank you! I was struggling to pair mine and it wasn't working. I did a plug-unplug while holding buttons thing and now it works!
You see folks... initiatives like this drive humanity and knowledge further.
So helpful! I thought my remote was broken! Thank you!
I lost my remote so purchased new controller/remote kit on eBay, paired it with your help. Thank you. Surprised the original which looked very similar wouldn't respond to pairing attempts. Was purchased at Home Depot, Commercial Electric brand. Maybe it was older or something. The controller module has the same shape, wire gauge, color etc so I'll be swapping them out tonight, so I have a remote again.
So I have had remotes that stop working. The fix in all so far has been to look in the battery compartment and bend the tabs that makes contact with the negative towards the door... should be the spring metal to the sides. My assumption is that dropping the remote a sufficient number of times allows the weight of the battery in deceleration to bend the tabs so contact is broken. I am glad you got a solution working again.
Thank you very much. I need this kind of tutorial :)
So helpful! Thank You!
Good video, now i know how to programm it,
Of great help! Thank you so much
Brill! Thanks for this!
You saved me. thank you very much.
Thanks,Very helpful.
hope our 5050 rgb led strip can help you,details:www.alibaba.com/product-detail/aluminum-housing-profile-5050smd-rgb-led_60823816841.html?spm=a2747.manage.list.4.74d571d2qjHV24
I'm in the same boat as several others. My remote just stopped working I tried batteries and still nothing.. thanks for doing this video!
좋은 정보 고마워요
I found an additional programming instruction for "Free Pairing Mode" or also called "Unpaired Mode". Unplug controller for at least five seconds, plug back in, within five seconds hold down "On/Off" and "Mode+" buttons for five seconds. Although, I'm not quite sure what the point of "Unpaired mode" is? Why not just do the pairing procedure with all controllers powered and then just unplug those out of on/off sync, hit the power button on the remote, then plug the others back in again to have them all in on/off sync.
All said, you are absolutely correct, some versions of these remotes use the 50% & 100% buttons instead of the speed buttons. The same may be true for the "Free pairing mode". :)
By the way, thank you for this excellent demo!
great video solve my problem
I just discovered that when you first get the controllers (the wired part that receives the signal), apparently they are in universal mode where they will respond to any remote regardless of whether that remote has been reprogrammed or not. But once you program a controller, that controller will now only ever work with one remote at a time, whichever the last one was that you paired it with. I don't know if there is any w ay to set the controller back to universal mode again. I tried different things but couldn't get anything to work. So the trick is to use a new unprogrammed controller if you want to have several remotes controlling the same thing. But then you may have a problem if anyone else nearby is using a similar remote or similar frequency, your lights might get turned on or off unexpectedly.
After switching of mainpower, do the controler remember last settings?
I wanna set the led's all time at 50% but for on/off i dont wanna use the remote.
Thanks for help and sorry for my bad english
Yes. I demonstrate the behavior for this and other dimmers in this video. ua-cam.com/video/0cS6sI1aYOc/v-deo.html
thank you so much i love this item but i didn't know how to get it to work separately
Can they be configured so that a single dimmer is controllable by two or more remotes? I want a remote by my bed and another by the bedroom door.
No. Look through the comments for others that have listed similar questions. I have suggestions of products that can do that via dual remotes or voice.
I also solved the pairing problem. Disconnect the power for 5 seconds, reconnect, and press the speed + and speed - together in 5 seconds. The LED must flash once and the pairing is done. I hope it will help
- Mirek - This has not worked for me at all
It's good.
Is there a way to force ON or OFF, not toggle? I have more than one light strip in the same electrical circuit, and it happened that the lights are "out of sync" with one another. Turning the circuit off does not solve, as the controllers have memory... Any idea? Thank you for your video.
No. I also tried getting one remote to talk to two controllers for someone and that did not work.
Options: if you can get a wire between them a one color amplifier will allow you to extend control and keep the second power supply for the second string... and you get one controller control. Another option is rgb wifi controllers (with the infrared remote option if you want) the wifi gives you phone control of each light separately. You obviously are not using the color lights so use the common (which is usually the positive) and one color. You could also do something similar with the cheaper regular color controllers. Another option might be the Mi-light WiFi Led controller system. They used to make one color and rgb color modules.
Hi, I have the 17 button rf controller. Have played around with every button combination but No luck. It's the exact remote as yours in the video but has the colour buttons. Instructions say speed minus and plus but still does not work. Do you have anything else I could try?
I do not. All the color controllers I use are IR or WiFi. I have also used Bluetooth enabled when WiFi was not available.
Thanks
Have you noticed any flickering during high fps while making videos ? What is the speed of pwm ?
Towards the end of this other video I made on one color dimmers I cover what is causing that. ua-cam.com/video/0cS6sI1aYOc/v-deo.html
Is it possible to use for motor like small ones that are use in rc cars? And can it be powered with a Double AA or AAA Battery? I am curious though since I know only little about electronics?
No. These controllers make dirty power by creating the flashing to give the illusion of traditional dimming. You want a DC motor controller. I don't know if I have seen one with a remote, but they are likely out there. I have use such things on some printing projects.
i try but not working i have 6 remote but not possible in each separate my led control 5-24v with pin please help me if possible thanks
I have the same items in cant get the remotes to program why tried them - and + together over 3 times
I have led lights on my stairs. I have one remote at the top and one remote at the bottom. Worked for about a year and then something got it out of sync so that no remotes worked. Used your video to reprogram. Do you know how to make 2 remotes work with one receiver?
I tested that and found no way to intentionally make both work with one remote. I am thinking of doing my stairs soon. I will probably try dual motion with a blocking rectifier. Voice activated is tempting but Alexa or google screaming ok in the middle of the night may not go over well.
Look at the mi-light controllers. One remote can control up to 4 controllers and you have the option of multiple remotes.
@@alwaystinkering6972 Thanks for the input! Lately I have been just reprogramming the lights every time I us the remote at the top or bottom of the stairs.
I use RGB controller with RF control. And i have many problems with connection controller and remote control. Сonnections is lost on many controllers. Can you help me? Are there hidden control panel features?
All of my color controllers are infrared or WiFi or WiFi/infrared. The WiFi infrared work best for me because I can use my phone to control the lights and the non-tech people in my house can use the remote.
While there a growing number of options you will find that the offers under multiple brand names are the same product. This means you should be able to shop price. This link is an example of an infrared with WiFi www.amazon.com/dp/B07BRWTQCS they come in RGB and RGBW format.
A broader selection could be seen by searching “wifi rgb led controller”
I hope you find a solution that works for you.
Neither option worked for my remote although it looks identical. Any remote controls all lights. I will just switch the second circuit from RF control to IR.
Make sure you have only one powered on when pressing the buttons to do the programming. Pressing the programming keys will reset all powered dimmers within range to be controlled by that one remote. There are appear to be multiple places manufacturing this design so at some point behavior may change.
full thx
Does this technique work with any brand of rf led controller?
Many if not all RF remotes seam to have some process to re-associate the pairing. No two seam to follow the same process and key combination. Few are documented with the instructions. So the answer is no. This one does not apply to any brand.
I search for how to restart the controller. That it will work back to all unit. ( standard that it come in the box )
The 17 key RGB version of the remote doesn't work like this. In fact I think it's not capable of different channels at all
Would this controller work with an LED that is powered by 2 AA batteries? It says the working voltage is DC12~24...
I have never tried it but being below the 12v lower rating it probably would not. If you look at usb led and dimmers those operate at 5v. So they may operate with 3 batteries for 4.5 volts. That would have to be tested. Maybe you can find some costume led’s that have a remote. Those are designed to work with batteries.
@@alwaystinkering6972thank you very much! So I changed the operation of the LEDs to 3 AAA batteries (by connecting it to an old 3 AA battery holder I had) and the remote worked BUT it was not enough to entirely stop the current. My guess is that these LEDs don't have any resistors and will turn on with any small amount of current that passes. Since I had ordered two controllers, I placed them in series and managed to entirely turn off (and on) using the controller. Definitely not the most elegant solution, but at least I managed to do something with the parts I already had. Thanks again for your help!
Good day. Thanks for the helpful video. Tell me, maybe You know, how one controller to register 2 remote controls. Thank you in advance.
Mi-light makes a system with multiple remotes to multiple controllers. Usually each remote can do up to 4 controllers. Another option would be phone controlled controllers if you want to use multiple phones for control. Phone enabled are more common for controlling color. You can use them for single color by using just one band and making an adapter wire. On most color controllers each color is a (+) connector. The common is the (-).
Good afternoon. Thanks for the quick response. I need the reverse action-bind the second (optional) light control panel to one controller. So as to control two(1 and 2) remotes by one led strip.Thanks.
Добрый день. Спасибо за быстрый ответ. Мне нужно обратное действие - привязать второй(дополнительный) пульт управления светом на один контроллер. Так, чтобы управлять двумя(1 и 2) пультами одной светодиодной лентой.Спасибо.
No. As I show in the video sometimes they answer to the same remote, but getting both to respond is hit or miss. I have used some color controls that are run from your phone. The apps give you a list of controllers it sees. I only have one controller so i don't know if I could control more at the same time. Actually I do have a second controller that is supposed to use the same software. I will have to run a test to see if an action can do multiple at the same time. I had tested the wifi controller on an Alexa voice control. It worked well.
This should be able to power two 10w led lights right? I connected it and it worked fine for 10 minutes and then just died. And now it just flickers one time when i try to power it on.
The rating of label of 12A would be 144W at 12V DC as there are 12W per amp at that voltage. I run a rated load of 9A or 108W on a daily used string for over a year now. I say rated because the actual load created by a string is frequently less than its potential peak. As for diagnosing your problem. First verify that your 10W LED fixtures work without the dimmer. If the dimmer is toast you may want to remove the cover over the circuit board ( which is heat shrink) for analysis. Did anything melt? Do the wires test as functional and not broken. The one short I experienced melted the wiring insulation over the IC that overheated. You likely won't be able to fix a problem, but you may see something obvious in the issue, including a defect. Also check your power is putting out the correct voltage. Also remember, the printed instructions say it is rated for 6A... You still would have been OK... it is just a reminder that there is not telling what it should be.
Always Tinkering thanks for the reply. I think i just got a bad batch or something. I opened it up and i cant see anything burnt or obviously wrong with it. Now when i connect the leads it actually lights up, but it doesnt want to be controlled. The controller it self is fine and working however. So now it only acts as a peice of wire... Ill order a new one and see if it happends again. I plan to use it on my motorcycle. I want to use these insainly bright tiny work lights as drl's and being able to set the brightness will help me being seen, without blinding other drivers. Especially when its getting darker or raining. Do you think theres a better solution to this? I really like the idea of being able to strobe them as well.
Whitch fuse I shlould use for my motorcycle ? It’s 12V
The one above the rated amp draw of the led lights you are using and no higher than the rating on the next lowest rated item... wire... switch and such. At 12v it is 1 amp per 12w of rating.
If you had a 12w light thats 1 amp. 1amp fuse may be too close, 2 amp would be the lowest. You are protecting against a short.
You don't want that short to pass enough amps it can melt something and cause a fire. Unless you are pushing the full rating, a 10 amp fuse should protect this dimmer... if you trust the factory wiring on it. So if you are using lights with a lower draw than the dimmer rating, fuse at the light rating.
Not flashing after pressing the speed buttons. Tried everything, but 1 remote still controls the 2 led in the same time. One in the kitchen, and one in the bedroom.. Ideas?
Are the remote keys in the exact same layout? There is another remote that is of the same size with a different key layout. That remote uses a different key combination. I have not seen any changes, but it is always possible they could update the chip set. Also make sure to try it right after the power on.
Both are the 17 key rf remote. In the manual there is the same method but..
ua-cam.com/video/U5jYMBW11GE/v-deo.html - this type.
Color too. Definitely different. I don't have any with that layout. Try different key combinations within 5 seconds of power on. It is likely there someplace. Things like bright up and down. Also try holding buttons at power on.
If I use a battery box with an 23A type 12V Battery I will have any issue with the controller?
Its the load that determines if you can use it. The dimmer may make it as high as 12 amps. I have a 9 amp rated run. I replaced the wires on the unit with a higher 18 gauge wire. Beyond that you need an amplifier to go above the rating. The amp will transmit the dimmer functuons onto distant led lines but not the load of those lines. The amp does this by requiring power be run directly to the amp. The at power is used for the lights it controls. You can power a main line and an amp from the same source power so long as it is rated for the total load and the distance to the amp does not cause a significant loss of power. You can also look at higher amp solutions like DC12-24V 30A LED Single Color LED Dimmer Controller with RF Wireless Remote www.amazon.com/dp/B06Y5M6CX4 i review the mechanical version of this switch in my one color dimmer review.
@@alwaystinkering6972 The strip will be just 50cm 5050.
The Battery I want to use is the small one usually use in car alarms controls or garage controls.
The name of the battery is 23A its not 23 Amper.
www.google.com/search?q=23a+battery&client=firefox-b-d&tbm=isch&source=iu&ictx=1&fir=tdJ8ko7n7yWpgM%253A%252C1AReXucBygSmXM%252C_&vet=1&usg=AI4_-kSvW5Qq7kbM4Aj6XjxW45QbQ-t_rQ&sa=X&ved=2ahUKEwjgi_vq3sDiAhUiSxUIHZzlDs4Q9QEwAnoECAkQBg#imgrc=_&vet=1
@@dragonld123 you should be good. When using straight battery power remember to use a fuse in line. You want short protection.
Hello I just purchased this kit off eBay and it lights but the remote does not! I tried binding it like you did but nothing!
The IR light on the front of the remote usually lights even though the remote is RF. If it does not look like it is working the battery may not be making contact. When you slide the battery in it makes contact on the (+) surface and then there is a piece of spring metal that makes contact with the sides (0). I have dropped a remote 12 too many times and bend the spring metal so it does not make contact with the sides. I fixed that with a small screw driver that pulled the spring wings back out.
I am assuming you have the same layout on your remote. Hopefully it is something that simple.
@@alwaystinkering6972 yes it is the same remote. It does light when buttons are pushed and I tried a new battery also. Does it matter were I put the positive led? I went to battery voltage that is hot all the time, so I can turn the lights on anytime! The LED's work great and the control box does not get hot.
Hi can i use this with 5 meter led strip even
Yes, It is based on load. I have one running 9 meters of light rated at 1 amp per meter. I did solder in new leads of a higher gauge first to run at that rating. You should have no issues.
If I only use 1 of these for 4 LED light strips, will I loose anything as far as Amps going to the LED with a 12V power source. I only bought 1 and still waiting for it in the mail....Pls help...
If you have qty 4 5 amp lines that is 20 amp and too much draw. Of course qty 4 5 amp would require you add an amplifier after at least two runs that will keep the draw on the dimmer within spec. You can get 30 amp dimmers. You would still need to home run off the dimmer to farther runs. As far as voltage drop. On my 9 amp run I replaced the wires on this unit with 18 ga wire. I re heat shrinked it shut. Two years and still going. When running 12v over distance to the start of the line a larger gauge wire will help avoid drop. Here is the 30 amp with remote. I have used the mechanical version of this and include that in my one color dimmer review. LED4Everything (TM) DC12-24V 30A LED Single Color LED Dimmer Controller with RF Wireless Remote for 5050 3528 www.amazon.com/dp/B06Y5M6CX4/
do you know where I can get 3 of these mother boards without the controller... I just ordered 1 w/the controller,,, want to operate a total of underwater led shrimp lights I made with one controller...
I just want to buy 3 more receivers... where can I buy them?
If I connect two in series, can I reduce the brightness even more?
You should not connect two in series as the second in line will get dirty power. LED’s don’t dim as a regular bulb. While they do look duller with a slightly lower voltage, the dimmers electronics flash on and off at an huge rate of speed and the momentary illumination rate gives us brightness.
That being said the led’s have a point at which they illuminate and that point is their dimmest illumination.
The best way to make things dimmer would be to include fewer led’s when at the lowest illumination. You could do that by… addressable led’s and a controller you can customize. You could use two strips with fewer led’s per meter and put on on one controller and one on the other…. Or your could take a strip you have an go through the labor of wiring two lines in parallel with wire attaching the sections so they offset in an alternating manor…. One on each controller.
… and the large black unit is still the best dimmer controller I have used for attaining smoothness when approaching the lower settings. I recall their being a wireless version of it.
Oh. I should mention I have another video where just cover one color dimmers available at that time…. If you have not seen it.
Thanks for your reply!! Very interesting! In my case it's a lamp which illuminates an acrylic base so I wished to do not disassemble it. Anyways, thank so much for taking your time to explain
What do I do if I want two remotes to control the same strip?
Not with this controller. There are a couple of options. For remote based looks at mi-light. Each remote can do up to 4 controllers and you can have multiple remotes. The other is phone or voice control. That can be a WiFi or Bluetooth based controller. I demonstrate a WiFi controller in this video. ua-cam.com/video/SAyy_kZojv0/v-deo.html
Is that means constant war with neighbor ,,is led RF controller can possibly be the begining of civil war ?-:)
I just want to buy 3 more receivers... where can I buy them?
One remote will not relaibly turn them all on and off at the same time. Visit the frentaly store on ebay. They usually have 3 for under 10.
Rgr… got about 5... I did program them each separately, then connected them all to one battery. 1 remote seems to work fine so far. I haven't been able to get them to not work all 4 together.... hope this luck continues during my shrimping.... thanks again...
@@alwaystinkering6972
Anyone know where I can buy these from?
I have bought many un terminated 3 packs from ebay seller frentaly out of georgia. They can also easily be found by searching RF LED REMOTE ONE COLOR in ebay or amazon. Here is the current frentaly ebay item number to search for 231935716776
I have 2 slightly different remotes and this doesn’t work for me they’re both RF wireless but + - doesn’t make them flash at all and I can still control both with one remotes anyone have some suggestions??
Different Remotes don’t seam to follow the same procedure. Try different key combinations. Some seam to only allow programming within a couple of seconds of powering on the controller... as it probably should be. So keep that in mind in your attempts.
Always Tinkering thank you for replying and explaining I’ll have a look around and see how to set mine 👍🏻
the maximum distance how many meters. can we press the 20 meter button to function
I went outside and ran some tests. Very reliable at 20 meters with a new battery and old. Ok at 30 meters very random by 50 meters and nothing at 60 meters. At 20 meters I can reliably control the front lights over my garage. That sensor is behind the wood and stucco of the roof overhang. So yes. You should be ok at 20 meters.
where to buy it. there is a link
@@cecuenwu8842 you can find them on eBay and Amazon searching “one color led rf dimmer” here is a randomly picked example of a seller offering a 2 pack www.ebay.com/itm/2X-DC12V-12A-RF-Wireless-Remote-Mini-Controller-Dimmer-Led-Single-Color-Strip-/192562194727
i have two remotes for 1 strip is there an option to program that
I am always hesident to feed electricity backwards into a device that does not clearly indicate it supports that configuration. One remote activating the power would create that scenerio for the other controller. Consider the milight remote control system that allows you to have one controller and multiple remotes. That system also has a wifi option you can add for additional control. That being said you could also get a standalone wifi controller that has an ir remote option. Phone would be one remote and the ir remote the other.
Always Tinkering no i have one controler on the led strip but i have 2 remotes
I grabbed a battery pack, two remotes, a controller, some light and went out into a field to run a test. I was unable to get two remotes to talk to the same controller. I could swing controller control back and forth between remotes (I guess that is an option if you have no other controllers... just resync when you go to use the remote).
I tried sending the sync sequence at the same time, only one would win. I tried numerous other key combinations with the loser and it would never gain simultaneous control. I also cycled through resync's on one controller to see if there would be some overlap at some point... and I encountered none.
From this experiment I would say the controllers build their sync off what the remote sends... and that the controllers must us the same or a similar algorithm since we know the reset sequence will reprogram all controllers in range... and many will then then be controlled by that one remote.
ok thanks for reply
Thank you as well, UA-camrs named “LizardLed” can’t explain anything.
does yours work with 5volt using usb supply ?? mine doesnt working :(
The ones in this video are rated at 12 to 24v dc. 5v is common in controllers and lights running of usb power since usb runs at 5v. You should be able to find similar units that rating.
thanks so much for reply my comment :) i bought 4 remote control throught shopee, they look like yours in this clip, i'll try with 12v led light.
sadly they're not work with my 5v fairy light
my rf control labeled working voltage from 5-24v :(
Try to verify it is working someplace else. Sometimes the battery contact does not touch the contact. I see some of the 5 to 24v online but none of the reviews mention using them ah 5v. I hope it works out.
Always Tinkering thanks so much :) have a good day sir 😝
ok great but it would help to know what controller it is
A search of ebay or amazon with the phrase "single color led rf controller" will display many suppliers.
Hi i cant program my controler, could you help me?
The controller is not working and I'm trying to pair it and i Can't
If your remote is identical to these and it is not working or syncing, Check that the wire assembly is not getting HOT. That is a sign that it has been damaged by a short. If it has been damaged it will make it useless. The I damaged during an install let the lights turn on, but all control was lost.
If your remote is not the identical layout I have seen other videos for the remotes with the different layout that show the 50% and 100% buttons being used to do the programming.
I hope that helps. Good luck.
I also solved the pairing problem. Disconnect the power for 5 seconds, reconnect, and press the speed + and speed - together in 5 seconds. The LED must flash once and the pairing is done. I hope it will help
@@alwaystinkering6972 I have 2 receivers and they both stopped working, running hot. The LEDs are always on. I removed the shrink wrap from one of them and found 3 A2SHB mosfet surface mount devices (SMD) which I think are the output devices. Two of the devices have zero Ohms from drain to source, which I suspect would cause the output to be stuck on. I am trying to grow my SMD skills so I ordered some devices from eBay $1.99 for 100 pieces. I plan to replace those mosfets and see if the receiver starts working again. I also have some replacement receivers on order so I can compare good with bad. Why all of this for a $2 device? I tinker too.
@@skiptourville823 Interesting. They stopped working with just an LED strip load? Any lights on the strip out? What voltage and load do you run? The 27' over the garage is my largest load (I did replace the wire leads with 18 ga). I am 2+ years now with that one. I have had some remotes wig out. The metal prongs that touch the edge of the battery tend to not spring back if the remote has bounced off the floor too many times. I just bend them back. Other than that the dozen plus I have installed are all still running. If you have no short and your draw is too near the rating try an amplifier. Mixed luck with those. The in expensive one color amps are usually RGB inside with the RGB shorted into one color. Not an issue but the failure rate has been more than one. The good news about working on your SMD skills is that it is only a $2 device.
I bought this today and when I turn it on all it does is strobe the led strip. remote does not work. led controller faulty?
I have not encountered that. Does the unit get hot. If it is getting really hot fast maybe the label and the wires don’t match. Wiring it backwards may burn it out so observe, not test. . Are the led’s on the side labeled led?
If the remote is powered properly you can see an light illumination when you press a button. No light the remote may not be powering and the flashing is just the mode the unit was in when it powered down. If there is no power in the remote the battery obviously has to be good. Inside the remote there are two metal wings that make contact with the negative sides. Sometimes they bend too straight and don’t make contact.
@@alwaystinkering6972 item does not get hot and it's all labelled and the remote light is working fine when I press button. so I dont think it remote.
Если диммер не реагирует на пульт, просто попробуйте запрограмировать пульт по этой инструкции. У меня заработал. СПАСИБО
my remote not working anymore, i hope il make it after this video.
This tutorial was helpful, thank you! But how can I bring back the basic settings now?
What do you mean by basic settings? Once paired the adjustment options should all work.
@@alwaystinkering6972 I mean i paired controller & remote, they all work great. But now I want to bring back the factory settings that were before I paired them. How can I do that? Is it possible?
@@assetyermekbayev460 not that I know. Powering all the receivers and trying to sync just one remote with them all should mess them up well enough. Just remember which remote you used when you move on to whatever their next phase in life is.
@@alwaystinkering6972 I paired 3 remotes and 3 receivers, so now 1 receiver works with 1 remote. But before I did that 1 remote worked with 3 receivers. I want to reset the settings/options to what they were before I paired them
@@assetyermekbayev460 I recently found decent instructions posted with this Amazon post. Updated Mini Remote Controller for Single Color LED Strip Lights, RF Dimmer for 12V DC LED Ribbon, Shelf Lights, Wireless Remote Control for Dimmable 3528 5050 Under Cabinet Puck Lights(Single Color) www.amazon.com/dp/B01M7TGZ9B
My remote doesn't have the speed buttons 😕
While I have not tried many other remotes, I have come across documentation that other remotes can be programmed with different combinations. I looked at a remote with just brightness up/down and the % brightness buttons. It had these instructions. If this does not work, see if different combinations will. Disconnect the power to the LED controller, wait 5 seconds, and reconnect.
2. Within 5 seconds of reconnecting the LED Controller, press the “100%” and
“60%” buttons simultaneously.
17 key rgb Can you help me identify
Thanks
Try unplugging 10 seconds. Plug in. Press color - and bright - together within 10 seconds of power on If the led lights flash then they paired.
@@alwaystinkering6972
This 17 key mini RF remote
I tried on this product
I am not sorry.
Hi, I'm waiting for your help. The LED flashes after a while. I am using a 12V 6A Adapter. Why is he doing this? I am using it for aquarium lighting and it is really annoying.
What kind of flashing? Power cutting out random flashing or a line one of the programmed flashing modes. Is the led strip fully enclosed or a strip with the silicone gel?
@@alwaystinkering6972
3 pcs led I use this: canleddunyasi.com/wp-content/uploads/2018/02/170.jpg
I just want it to burn normally and I make the light intensity 25%.
But after a while the light blinks and returns to normal. It repeats after an uncertain time. It's like a flicker. This makes a very bad appearance.
@@alwaystinkering6972 ua-cam.com/video/5TJuJPoOk_Q/v-deo.html I uploaded a video about it.
It's like pressing the Speed + and Speed - buttons.
Woud definitly install a 5A fuze
It's our product.
3:27
Thanks.. over 3 minutes to get to the fuckin point lol
It didn't work.😭 The light on the remote comes on but doesn't do anything else.
Make sure the controller has power and the polarity to the lights and power is correct. The controllers have no indicator of the are functioning other than to flash the attached lights so you are dependent on them functioning. Best of luck.
@@alwaystinkering6972 what does it mean to make sure the controller has power and polarity to the lights and power is correct?
@@void________ plug the power direct to the lights to make sure it works. Then put the power back to the controller. I don’t know which controller you have, with the pre attached connectors or ones you connect. If it is the ones you connect make sure red is on (+) on both sides.
This didn’t work at all for me. Interesting.
YOU ARE TALKING LIKE SOMEBODY TALKING OUT LOAD TO THEM SELF. NOBODY CAN UNDERSTAND WHAT YOU ARE TALKING ABOUT....................INSTEAD OF DOING YOUR THING AND TALKING POINT BLANK ABOUT WHAT YOU ARE DOING, YOU ARE TALKING LIKE WE WERE SOMEBODY YOU DON'T CARE ABOUT................