K. I went to Lowe's and bought 3 kits (it comes with spline, connectors, etc...), and did three windows. It is easy when following your steps. Thanks again!
I'm assuming your talking about Latches? If so I've added a link to the bottom of the description. Most of the latches we sell just slide onto the frame, others install into the spline channel.
Thanks for all the help, by the way, I am also looking for the hooks that I currently have on my Andersen screen. do you sell them, and is it easy to install them on the screen frame so that I can attach it to the existing holes
@spxrt I have two different brands of these screen kits this brand here and another brand. I cut an assembled all the frames so far and only put a screen in one of them so far and it bowed in the middle like you say. This brand I noticed seemd to be a little more rigid. In fact when I put the frame of the one that bowed up against this brand it was already bowed even before I put the screen in it! So for the two I made with the OTHER brand I will have to get a spreader bar.
Thanks, how many screws do you think I would need, the screen is about 25" x 42", maybe every 6 inches...also, should I use some sort of adhesive with the screws? Thanks for all your help!!
@spxrt I can't speak on the quality of the screen frame you're working with (As I don't know the brand or where it was purchased). If this is a large screen I would recommend a "spreader bar" across the middle of the screen to keep the frame from bowing in. I'll post a link to the spreader bar clips you can use to make a bar with, using another piece of screen frame. These clips slip into the ends of the bar (frame) and are placed across the middle of the frame, spline holds the bar in.
I am trying to build a replacement for my screen using a screen frame and plexiglass. I need to do this to us my portable ac unit. I have the frame made but how could I attach the plexiglass to it...any suggestions?
Every 6-8 inches should be fine I would think. You may even run a thin piece of foam weatherstrip between the plexiglass and the frame (to keep it from possibly rattling in windy conditions) Remember if you do that, you may have to get slightly longer screws. Also, don't tighten down the screws too tight, plexiglass splits very easily. Lexan however doesn't have this problem, and is much stronger if you haven't already purchased the material yet.
If making a storm window with vinyl film, is it best to use the channels and spline, use a double sided tape, or is there a better method? How does one remove/prevent the wrinkles in the film? Thanks!
Andreas Guntoro Not sure I understand the question. Here is our selection of springs for window screens. primeline.net/home4.wcs?nMenuid=3310&cProd=PL&cSProd=037 Are you having trouble with a specific type of spring?
We sell about 160 different colors/styles of screen clips. They hold the screen in without springs. As for the ring, without using the springs the screen is much easier to get out.
@markcastle1 We appreciate your feedback and concern for someone injuring themselves, but we believe securing screen frames onto a working surface is much safer when cutting the screen fabric. The average "Do It Yourself" person will be more at risk cutting themselves when they are trying to hold onto a loose screen frame and cutting the screen fabric at the same time. Not everyone has a purpose built screening table in their garage. However If they'd like to, our part number is P-8101.
Either on the face, or the backside of the frame you could use #6 or #8 sheet metal screws, 3/8" long. Cut the plexiglass the same size as the frame. Next, drill holes around the edge that are big enough for the screw to slide into without having to twist them. (You don't want to crack the plexi) Then lay the plexi on top of the frame, and with a smaller bit, drill pilot holes for the screws (Only through the first layer of metal) Attach plexi with screws. Good Luck!
@yungscanlist We sell the kits in 36", 48" & 60" sizes. Prices vary by where you buy them, but should be less than $20 each. Available at Ace Hardware, TrueValue, Lowes, Orchard, Do-It-Best, etc etc.. Good luck on your screening project, and glad we could help.
A screw goes in the hole in the clip, and the clip can rotate over the edge of the screen, holding it in, or it can rotate out of the way, allowing you to remove the screen. One screw per clip, four per window. I've added a link to the screen clip instruction sheet (PDF File) in the description. The clips are just one way to keep the screen in. We sell many other parts to do this.
Plexiglass won't work for this kind of frame. You could use plastic sheeting (thick dropcloth material) with this frame. We have another video that shows how to build a storm window using plexi. You can see that video here: ua-cam.com/video/QqI6eFnaICg/v-deo.html
It would be best to use spline. Depending on the thickness of the vinyl film, you may have to use thicker or thinner spline than you would normally use with screen. For the wrinkles. Botox. Ok, just kidding. Two things, practice, and they also sell a heat shrinkable film. You would install the film on the frame, then go over it with a hairdryer/heat gun, and shrink it until it's as tight as you need.
OK, I talked to my guy, he has a photo of what I think you're looking for, if you can PM an email address I can send you a photo. Either way, you'd have to go to an Anderson dealer to get the part.
K. I went to Lowe's and bought 3 kits (it comes with spline, connectors, etc...), and did three windows. It is easy when following your steps. Thanks again!
Really well done tutorial. Great voice and camera work.
Great tutorial. I bought the kit and delayed getting started for weeks. I think I get it now.
2 windows newly screened. Thanks again.
+Anthony Devine It's easy once you know how. :-)
I'm assuming your talking about Latches? If so I've added a link to the bottom of the description. Most of the latches we sell just slide onto the frame, others install into the spline channel.
Thanks for all the help, by the way, I am also looking for the hooks that I currently have on my Andersen screen. do you sell them, and is it easy to install them on the screen frame so that I can attach it to the existing holes
@spxrt I have two different brands of these screen kits this brand here and another brand. I cut an assembled all the frames so far and only put a screen in one of them so far and it bowed in the middle like you say. This brand I noticed seemd to be a little more rigid. In fact when I put the frame of the one that bowed up against this brand it was already bowed even before I put the screen in it! So for the two I made with the OTHER brand I will have to get a spreader bar.
Thanks, how many screws do you think I would need, the screen is about 25" x 42", maybe every 6 inches...also, should I use some sort of adhesive with the screws? Thanks for all your help!!
Great video Very Good demonstration, Thank you for making this tutorial Video.
@HALIHALAO Thanks for stopping by to watch it. Good luck with your next screening project.
This how-to is perfect. Thanks!!
Excellent video. Very helpful
@spxrt I can't speak on the quality of the screen frame you're working with (As I don't know the brand or where it was purchased). If this is a large screen I would recommend a "spreader bar" across the middle of the screen to keep the frame from bowing in. I'll post a link to the spreader bar clips you can use to make a bar with, using another piece of screen frame. These clips slip into the ends of the bar (frame) and are placed across the middle of the frame, spline holds the bar in.
How do I make a storm window?
I am trying to build a replacement for my screen using a screen frame and plexiglass. I need to do this to us my portable ac unit. I have the frame made but how could I attach the plexiglass to it...any suggestions?
Every 6-8 inches should be fine I would think. You may even run a thin piece of foam weatherstrip between the plexiglass and the frame (to keep it from possibly rattling in windy conditions) Remember if you do that, you may have to get slightly longer screws.
Also, don't tighten down the screws too tight, plexiglass splits very easily. Lexan however doesn't have this problem, and is much stronger if you haven't already purchased the material yet.
If making a storm window with vinyl film, is it best to use the channels and spline, use a double sided tape, or is there a better method? How does one remove/prevent the wrinkles in the film? Thanks!
Just what I'm looking for, any advice on the spring? video or product link? I need to make two of complete 23 x 45 window screens. thank you so much.
Andreas Guntoro Not sure I understand the question. Here is our selection of springs for window screens. primeline.net/home4.wcs?nMenuid=3310&cProd=PL&cSProd=037
Are you having trouble with a specific type of spring?
Thank you for the fast reply and the link to your window screen springs. I'm sorry if the question is confusing.
Do you have pictures of those screen clips?
@batonrougeproperties Thank You. We're going to try and cover some of the more common screening and household repair issues.
We sell about 160 different colors/styles of screen clips. They hold the screen in without springs. As for the ring, without using the springs the screen is much easier to get out.
I have a 40" x 78" window. do you know of a kit that would cover that size?
Thanks for watching, and glad the screens turned out good.
Glad you liked it. Thanks for watching.
@yamaone114 Great! Let us know how it turns out.
@markcastle1 We appreciate your feedback and concern for someone injuring themselves, but we believe securing screen frames onto a working surface is much safer when cutting the screen fabric.
The average "Do It Yourself" person will be more at risk cutting themselves when they are trying to hold onto a loose screen frame and cutting the screen fabric at the same time.
Not everyone has a purpose built screening table in their garage. However If they'd like to, our part number is P-8101.
@yamaone114 Glad it worked out for you. They're really not that hard to build once you've done one or two of them.
Either on the face, or the backside of the frame you could use #6 or #8 sheet metal screws, 3/8" long.
Cut the plexiglass the same size as the frame. Next, drill holes around the edge that are big enough for the screw to slide into without having to twist them. (You don't want to crack the plexi) Then lay the plexi on top of the frame, and with a smaller bit, drill pilot holes for the screws (Only through the first layer of metal) Attach plexi with screws. Good Luck!
Mine always turn out warped or bowed, any advice on how to prevent this?
awsome video
@yungscanlist We sell the kits in 36", 48" & 60" sizes. Prices vary by where you buy them, but should be less than $20 each. Available at Ace Hardware, TrueValue, Lowes, Orchard, Do-It-Best, etc etc.. Good luck on your screening project, and glad we could help.
@MrDamnSHt Thank you for the compliment.
A screw goes in the hole in the clip, and the clip can rotate over the edge of the screen, holding it in, or it can rotate out of the way, allowing you to remove the screen. One screw per clip, four per window. I've added a link to the screen clip instruction sheet (PDF File) in the description.
The clips are just one way to keep the screen in. We sell many other parts to do this.
Hope your screens turn out great. Thanks for watching.
the video title mentions storm window kit. Can the video kit be used for s storm window with 1/8 inch plexi?
Plexiglass won't work for this kind of frame. You could use plastic sheeting (thick dropcloth material) with this frame. We have another video that shows how to build a storm window using plexi. You can see that video here: ua-cam.com/video/QqI6eFnaICg/v-deo.html
No springs, no grabber ring... how does it stay in? How do you get it out?
I added a link for you in the video description.
@cessna65423 Thanks for watching, and taking the time to comment.
@tchinen No tricks, no hidden tools, and really easy to do once you've done it a time or two. Thanks for watching.
I added a link in the video's description under "Screen Repair Kit listing" were we have a number of 48" x 84" kits.
It would be best to use spline. Depending on the thickness of the vinyl film, you may have to use thicker or thinner spline than you would normally use with screen. For the wrinkles. Botox. Ok, just kidding. Two things, practice, and they also sell a heat shrinkable film. You would install the film on the frame, then go over it with a hairdryer/heat gun, and shrink it until it's as tight as you need.
Thanks for watching. Let us know how your screen(s) turn out.
Where are the pull tabs and the lock springs....
Where is the storm window part of this.
That doesn't resemble anything I've ever seen... how does it work?
OK, I talked to my guy, he has a photo of what I think you're looking for, if you can PM an email address I can send you a photo. Either way, you'd have to go to an Anderson dealer to get the part.
where is the STORM window?
I see. Not good for me, not allowed to make holes in window frames. Thanks anyway.