Hello, sir, you can contact the maintenance personnel on our company's official website, and he can give you a more professional answer.www.zeusbtc.com/
Hello, sir, Repair the Hash board with medium temperature solder paste, the melting point is 183° Celsius. More : www.zeusbtc.com/ASIC-Miner-Repair/Parts-Tools-Details.asp?ID=264
@@ZEUSMINING I'm trying to set up my s9 tester, but the instruction to connect the USB wires to the tester seem very unclear to me. The USB that I received has 4 wires: Black, Red, White, and Green. But the instructions on the Bitmain website for a s9 tester say to use the black, red, and yellow wires... (!) ?? I don't want to fry circuits with wrong connections. Do you know of a pic that shows the actual finished product, after connecting the USB wires to the S9? Thank you so much!!
@@007mercucio Okay, I didn't really catch your meaning, sir. Please take a picture of that, And click on the website to communicate with our maintenance staff, he will provide a better service for you. www.zeusbtc.com/
hi there... i want to ask... can i reuse chip from partially faulty board to repair minor damage board? ie. i have 2 board.. board 1 problem with 8 chips.. board 2 problem with 1 chip.. can i take 1 chip from board 1 to repair board 2?
Hello, friends, you can contact professional maintenance personnel on our company's official website, and he can provide you with some help.www.zeusbtc.com/
Hi, could you please tell me how much do you heat the chip to get it removed? I literally take the hot air gun to 450 to 480 C and it doesn't wants to get out. I put the gun right in the center of the chip and use the special tools to try to remove the chip but it just doesn't.
I have an s9i hashboard and after heat sinks replacement my text fixture says check chain = asicnum 30. I tested resistances and voltages to 29-30-31-32 asic and is normal . any advice?
Hello, this is the link to the product, you can click to view the details. For purchase-related matters, please contact the website sales, he will provide you with better service. www.zeusbtc.com/ASIC-Miner-Repair/Parts-Tools-Details.asp?ID=271 WhatsApp：+8618623251355
Good Video but you showed several faults in the sample but only repaired chip 58-59. Does that solve all of the faults or was that only a solution for when chip number 58-59 is bad? Do you have a solution video for when there are three errors like the sample issue during the video? I think it was, a chip was bad, the hash board wasn’t recognized and it wasn’t getting power
The device finds the chip number with start from number 0 ? If number 8 is displayed, number 9 is faulty. Finding on board start from 0, 1, 2, .... 9 ?
short-circuit "co" testing point of chip that you think is number 8 to the heat-sink. then test again. if it shows no8 then test next chip. if it shows no9 test the other. if it shows no9 again then change no9 chip ;) otherwise go ahead and find which one isnt working
Good evening, how to detect when a "PIC" of antminer s9 and s9i fails using only the tester, what electrical measurements it should have and how it should be used in the "PIC". I appreciate the help you can do for me
Hello, this is the repair guide for S9. I hope it helps you. You can join our FaceBook "Antminer repair" group to discuss and learn. www.zeusbtc.com/manuals/Antminer-S9-Hash-Board-Repair-Guide.asp
hi. how are u my friend , i hope fine I wanted to ask you if you know how to repair asic failure 48 or less asic in old models. antminer s7, I have a lot of these arrested for faults in the 3 cards and I would like to put them to work. If you could guide me to repair them, I'd be grateful to the soul, my friend.
Hello, when i open Xshell 6 it connect to the divice via serial port, but when i turn on the test fixture nothing happen in Xshell 6, im affraid the files in my TF card are damage, can i get the files again? thanks
Hello, friends, you can contact professional maintenance personnel on our company's official website, and he can provide you with some help.www.zeusbtc.com/
The repair process of D3 is the same as the S9 principle, so if you are familiar with the repair of S9, in theory you can fix a lot of Antminer miners.
Hello, friends, you can contact professional maintenance personnel on our company's official website, and he can provide you with some help.www.zeusbtc.com/
Good Morning. Friends I have a problem with a S9j machine and I would like to know if someone can give me some support with the problem. What happens is that the machine turns on and starts well and even the green indicator LED turns on that everything is fine. But the lights or red LEDs of the cards do not turn on and the machine does not mine. So it has 0th and in the kener log it says that CRC counter = 34765. I already tried reinstalling the firmware, trying another controller, changing the cards ... And nothing worked for me .... Any help please?
From now on, you can leave your questions in the Zeus Mining Facebook group or Reddit community, and our professionals will select some of these questions every week for unified answers. The scope of the problem is mainly concentrated in the field of ordinary ASIC miner maintenance. The problem needs to be described clearly, preferably with pictures. This is an attempt, and valuable comments are welcome. facebook.com/groups/2377381515673070
If the RT voltage is abnormal, you can check the resistor connected to it. Of course, you can also contact our technician on WhatsApp: +8619123969124, he will provide you with better suggestion service.
@@JamesCook-zv7td hey James. first there is another thing that you should copy it in tf-card and put it in control board .after that the control board will be ready to accept the test-tool tf-card
Incredible work I want to give you the thanks for your work since you are helping many people I would like to be able to contact you if you can send me your email because I am interested in buying all the tools that you present in your video please communicate with me thank you
Hello, sir, you can contact our sales staff on our company's official website. There are all kinds of mining machines and accessories, as well as maintenance tools.www.zeusbtc.com/
@@هیدایەتاحمدنبی We provide free maintenance tutorials and manuals, but you need to purchase accessories and maintenance tools, and consultation is free.
Hi,
Do I need to connect the test tool also when measuring the chip voltage values? Or just connecting the power is enough?
When testing the voltage, you need to connect the power supply and run the test fixture to test it when the hash board is working.
@Kevin chau: How much watt has the hot air gun? What is the diameter of heat gun nozzle?
Do u have repair mining power supply ?
Hello, sir, you can contact the maintenance personnel on our company's official website, and he can give you a more professional answer.www.zeusbtc.com/
Hi, and thanks for the great video. What kind of solder paste is this? What temp does it melt at?
Hello, sir, Repair the Hash board with medium temperature solder paste, the melting point is 183° Celsius. More : www.zeusbtc.com/ASIC-Miner-Repair/Parts-Tools-Details.asp?ID=264
@@ZEUSMINING Okay, splendid. Thank you.
@@ZEUSMINING I'm trying to set up my s9 tester, but the instruction to connect the USB wires to the tester seem very unclear to me. The USB that I received has 4 wires: Black, Red, White, and Green. But the instructions on the Bitmain website for a s9 tester say to use the black, red, and yellow wires... (!) ?? I don't want to fry circuits with wrong connections. Do you know of a pic that shows the actual finished product, after connecting the USB wires to the S9? Thank you so much!!
@@007mercucio Okay, I didn't really catch your meaning, sir. Please take a picture of that, And click on the website to communicate with our maintenance staff, he will provide a better service for you. www.zeusbtc.com/
@@ZEUSMINING Okay, thank you! I got it figured out.
Where do you get the usb driver ?
I want to see if is the same procedure for repair antminer d3 and i want to order tools because i have some antminer d3 defected i want to repair
Hello. test fixture for l3+ it can use on D3 too
Kevin Chau you not have Any video with this detailed for L3 or D3
@@emirsh6955 ua-cam.com/video/yQisxABqRL8/v-deo.html
I have seen this video but it is not much more detail than for s9 with frequency voltage...
can usu chip test fixture with macbook??
Can I use xshell 7
voltage measurement did it, with 12 volts attach, or with diode scale,?
For testing accuracy. Fluke 15B+ is recommended. It will automatic detection of voltage values.
12 volts
first you should check the voltages. if they are ok, check diods
hi there... i want to ask... can i reuse chip from partially faulty board to repair minor damage board?
ie. i have 2 board..
board 1 problem with 8 chips..
board 2 problem with 1 chip..
can i take 1 chip from board 1 to repair board 2?
Hello, friends, you can contact professional maintenance personnel on our company's official website, and he can provide you with some help.www.zeusbtc.com/
Hi, could you please tell me how much do you heat the chip to get it removed? I literally take the hot air gun to 450 to 480 C and it doesn't wants to get out. I put the gun right in the center of the chip and use the special tools to try to remove the chip but it just doesn't.
It requires continuous heating for about 15-20 seconds. Before that, you need to remove the black gel around the chip.
@@ZEUSMINING hi there, how to remove the black gel?
@@rezashah5330 Scrape with scraping knife
I have an s9i hashboard and after heat sinks replacement my text fixture says check chain = asicnum 30. I tested resistances and voltages to 29-30-31-32 asic and is normal . any advice?
It is recommended that after replacing the heat sink, do a single board test again after a while.
Does this test fixture work with the S9J?
Yes. it can be work with S9 S9i S9J
Sir new board 9672047120
i what are the ratings of the heat gun
Hello, this is the link to the product, you can click to view the details. For purchase-related matters, please contact the website sales, he will provide you with better service.
www.zeusbtc.com/ASIC-Miner-Repair/Parts-Tools-Details.asp?ID=271
WhatsApp：+8618623251355
brawo
Dziękujemy za wsparcie, będziemy kontynuować ciężką pracę
Кто-нибудь может сказать, почему важно отпаивать нижний радиатор? Не проще ли сразу через него снизу нагреть чип?
Здравствуйте, сэр, вы можете связаться с обслуживающим персоналом на официальном сайте нашей компании, и он может вам помочь.www.zeusbtc.com/
Не нужн оего отпаивать - греешь просто и выпаиваешь или впаиваешь чип.
can you do a video using the multimetre , none of the values I get match the drawing
Good friend, we will consider this suggestion
Good Video but you showed several faults in the sample but only repaired chip 58-59. Does that solve all of the faults or was that only a solution for when chip number 58-59 is bad? Do you have a solution video for when there are three errors like the sample issue during the video? I think it was, a chip was bad, the hash board wasn’t recognized and it wasn’t getting power
And what type of glue is used to replace the heat sinks
Yes, as you said. The video mainly expresses the problem that the hash board cannot be recognized due to chip damage.
Hi, where can i get the repair tools and software? Above link doesn't seems working anymore...
Hello, you can buy it at our eBay store, and with the proof of purchase, you can enjoy our free technical guidance: www.ebay.com/itm/173596462837
my test fixture ends after "starting kernel". Does anyone know what the issue may be?
The device finds the chip number with start from number 0 ? If number 8 is displayed, number 9 is faulty. Finding on board start from 0, 1, 2, .... 9 ?
short-circuit "co" testing point of chip that you think is number 8 to the heat-sink. then test again. if it shows no8 then test next chip. if it shows no9 test the other. if it shows no9 again then change no9 chip ;) otherwise go ahead and find which one isnt working
Good evening, how to detect when a "PIC" of antminer s9 and s9i fails using only the tester, what electrical measurements it should have and how it should be used in the "PIC". I appreciate the help you can do for me
Hello, please click on the website to communicate with the maintenance staff www.zeusbtc.com/
hi can i know what does this mean ? check_asic_reg: chain J1 has 0 ASIC and how can i solve it?
Hello, this is the repair guide for S9. I hope it helps you. You can join our FaceBook "Antminer repair" group to discuss and learn.
www.zeusbtc.com/manuals/Antminer-S9-Hash-Board-Repair-Guide.asp
Hi.
Have you found a solution?
hi. how are u my friend , i hope fine
I wanted to ask you if you know how to repair asic failure 48 or less asic in old models. antminer s7, I have a lot of these arrested for faults in the 3 cards and I would like to put them to work. If you could guide me to repair them, I'd be grateful to the soul, my friend.
cause of lack of information. antminer s7 can't repair for now. sorry my friend.
Hello, when i open Xshell 6 it connect to the divice via serial port, but when i turn on the test fixture nothing happen in Xshell 6, im affraid the files in my TF card are damage, can i get the files again? thanks
Hello, friends, you can contact professional maintenance personnel on our company's official website, and he can provide you with some help.www.zeusbtc.com/
Can you make one this video for antminer d3 how to repair ?
The repair process of D3 is the same as the S9 principle, so if you are familiar with the repair of S9, in theory you can fix a lot of Antminer miners.
But if the problem is not the chips, but the lighting of the board, how do you solve it?
Hello, friends, you can contact professional maintenance personnel on our company's official website, and he can provide you with some help.www.zeusbtc.com/
Good Morning.
Friends I have a problem with a S9j machine and I would like to know if someone can give me some support with the problem.
What happens is that the machine turns on and starts well and even the green indicator LED turns on that everything is fine. But the lights or red LEDs of the cards do not turn on and the machine does not mine. So it has 0th and in the kener log it says that CRC counter = 34765.
I already tried reinstalling the firmware, trying another controller, changing the cards ... And nothing worked for me .... Any help please?
From now on, you can leave your questions in the Zeus Mining Facebook group or Reddit community, and our professionals will select some of these questions every week for unified answers.
The scope of the problem is mainly concentrated in the field of ordinary ASIC miner maintenance. The problem needs to be described clearly, preferably with pictures.
This is an attempt, and valuable comments are welcome.
facebook.com/groups/2377381515673070
this device work for new s11, t11, s15??
Hi. only for S9 and T9+
If you need S15 repair tools, our ebay is also available for sale, it applies to S15, T15, S11, www.ebay.com/itm/173999799089
Hello boss..saya penambang Kecil kecilan ..saya mau nanya..bagai mana cara membeli Sparepart Antminer S9 atau yg lain.mohon infonya boss
Silakan kunjungi situs web resmi kami untuk membeli. www.zeusbtc.com/ASIC-Miner-Repair/
Can some one share a link to download the xshell5 program.
Hi, here is the link to our Antminer hash board PIC file.
www.zeusbtc.com/ASIC-Miner-Repair/Parts-Tools-Details.asp?ID=220
Hello, where can I download the drivers?
www.zeusbtc.com/News.asp?Sort=FILES+DOWNLOAD, Also you can contact the maintenance staff on the homepage.
Does anyone here know how to tweak SCRT, so the text doesn't go shifting off to the right, further, with each successive line?
HI
Have you found a solution?
@@farkhoddaniyarov4909 No, I kind of dropped that project, for now. I suspect there is a way to change the formatting, though.
Rt error how to solve it?
If the RT voltage is abnormal, you can check the resistor connected to it.
Of course, you can also contact our technician on WhatsApp: +8619123969124, he will provide you with better suggestion service.
ممكن طريقه صيانه الباور كمان
تمام
Anyone have a question I'm ready to help
Hi can u help me. I cannot install the xshell5 software.
@@rezashah5330 I will upload the video soon on my channel, WhatsApp 0096171402063
Hi and thank you for sharing. My test tool just shows " send pic heart bit". What is the problem?
this problem is test fixture program error.
@@ZEUSMINING thnx mate. best wishes. I managed it with a sd card for making control board ready to be a test tool
@@kamranzahedi5977 Please advice howto fixit? We are trying 2 days already with no success
@@JamesCook-zv7td hey James. first there is another thing that you should copy it in tf-card and put it in control board .after that the control board will be ready to accept the test-tool tf-card
@@kamranzahedi5977 what thing, mate?;)
Зачем пасту плавить, если можно установив чип, во время припоя это сделать?
Incredible work I want to give you the thanks for your work since you are helping many people I would like to be able to contact you if you can send me your email because I am interested in buying all the tools that you present in your video please communicate with me thank you
Hello. my email: szechungchau@hotmail.com
Haw to buying?
Hello, sir, you can contact our sales staff on our company's official website. There are all kinds of mining machines and accessories, as well as maintenance tools.www.zeusbtc.com/
@@ZEUSMINING for free?
@@هیدایەتاحمدنبی We provide free maintenance tutorials and manuals, but you need to purchase accessories and maintenance tools, and consultation is free.
@@ZEUSMINING you can send me
@@هیدایەتاحمدنبی Of course Dear
Hi and thank you for sharing. My test tool just shows " send pic heart bit". What is the problem?
this program is test fixture program error.
@@ZEUSMINING Any idea how to fix it?
@@ZEUSMINING как решить проблему?
@@JamesCook-zv7td как решить проблему?
как решить проблему?