I was looking at the LED plugin… sticking a short LED strip above the door where my printer is at would be great. Can tell the status without having to open the room a bunch.
New here... I used Octoprint with my old anycubic kobra 2. I had no control, when I tried to adjust the z-offset it would not do anything and it wuold not let me adjust the print form the printer control penal... when I tried printing it scrached the build plate... Is the upgrade good to work better with the kobra 2 max...
Did you ever do a video for the web server for the spaghetti detective? I am not finding one. I have a plex server and would love to set up my own web server for the spaghetti detective
I think if you are going to be printing a lot then you need to go to Octoprint. You get a lot of great features like remote monitoring, AI base alerting, and the ability to do remote printing.
Its a lot less trouble than working on a printer screen, Just hook up via an old mobile with octaprint installed, go to the suggested ip on the phone and you're off , loads of plugins to chose from to make it better
Hello my friend. I followed your steps in the installation. It was fine until I installed some other plugins which generated a conflict. I uninstalled them all, and then came the problem. The Control and Temperature tabs are gone. I've tried everything. I uninstalled the program but it comes back with the same settings. I tried to find these plugins, but I can't find the right one. Can you help me on how to fix this? I can't control the machine (left, right etc. just connect). Thank you, hugs from Brazil
That is a shame. Have you tried upgrading to the latest version of octoprint? Another option might be to back up your settings and then reset octoprint and then restore your settings.
@@ThisSmartHouse I'm learning about octoprint. I have the latest version, I already reinstalled it, but the settings were saved I don't know where. I couldn't reset, and I couldn't find anything on the topic. I appreciate your attention, if you know anything about it, thank you my friend 🙏
If you don't care about saving any of your personalization settings then I would recommend just reflashing your raspberry Pi's SD card with a new octopi and just starting over again.
Content-wise this video is great. Thanks for that. But I find it very hard to watch due to how you cut video fragments together. Almost every few seconds the image jumps. It drives me crazy. So imho there’s room for improvement 🙂
3D printer in your BEDROOM is a BAD idea impo. 1. the fumes get into everything you are sleeping on. 2. microparticles of plastic land everywhere... Sleep tight and healthy !!! Take that thing out of your Bedroom..> OR... put it in an enclusure with active ventilation to the outdoors. Be well and happy 3D printing. PL.
That isn't my bedroom. It is my office which is also the spare bedroom. I don't think PLA outgassed harmful fumes. But an SLA printer is a different story .. It will go in my basement when I finish it and move my office.
Would love a tutorial on how to to set up the Leds to light up with octolapse!
I will have to probably do one because one of my kids pulled the wires and now the LEDs are dead...
I was looking at the LED plugin… sticking a short LED strip above the door where my printer is at would be great. Can tell the status without having to open the room a bunch.
I really like it, I could just look over at the printer and see where it is without opening the app.
Thank you. I use home-assistant, so really cool!
Great to hear! I love being able to integrate anything into Home Assistant.
Thanks for the great video, I would love to see how to setup the LED lighting with the Rasberry PI.
really nice to the point video. ty man.
Have you done a video on a standalone spaghetti or telegram bot install/setup?
How can we use ChatGPT to create a machine learning plugin? For printers like the CR-30?
New here... I used Octoprint with my old anycubic kobra 2. I had no control, when I tried to adjust the z-offset it would not do anything and it wuold not let me adjust the print form the printer control penal... when I tried printing it scrached the build plate... Is the upgrade good to work better with the kobra 2 max...
Awesome video! Hope to see more 3d printing videos
Thanks! I have some in the works...
It would be great to see a video on setting up a Spaghetti Detective server. I'm thinking of doing this myself.
Ok. I will add it to my list. I actually have one set up on one of my VMs.
This would be great!
2nd that
Did you ever do a video for the web server for the spaghetti detective? I am not finding one. I have a plex server and would love to set up my own web server for the spaghetti detective
I would love that light tutorial
I'm still at a begginer level and not using octoprint yet. Am I missing out?
I think if you are going to be printing a lot then you need to go to Octoprint. You get a lot of great features like remote monitoring, AI base alerting, and the ability to do remote printing.
@@ThisSmartHouse thanks
👍
Its a lot less trouble than working on a printer screen, Just hook up via an old mobile with octaprint installed, go to the suggested ip on the phone and you're off , loads of plugins to chose from to make it better
I like UI Customizer.....
Hello my friend. I followed your steps in the installation. It was fine until I installed some other plugins which generated a conflict. I uninstalled them all, and then came the problem. The Control and Temperature tabs are gone. I've tried everything. I uninstalled the program but it comes back with the same settings. I tried to find these plugins, but I can't find the right one.
Can you help me on how to fix this? I can't control the machine (left, right etc. just connect). Thank you, hugs from Brazil
That is a shame. Have you tried upgrading to the latest version of octoprint? Another option might be to back up your settings and then reset octoprint and then restore your settings.
@@ThisSmartHouse I'm learning about octoprint. I have the latest version, I already reinstalled it, but the settings were saved I don't know where. I couldn't reset, and I couldn't find anything on the topic. I appreciate your attention, if you know anything about it, thank you my friend 🙏
If you don't care about saving any of your personalization settings then I would recommend just reflashing your raspberry Pi's SD card with a new octopi and just starting over again.
Did you end up doing the WSLED video?
For the 3d printer? I ended up just replacing the LED strips with denser WS2812B strips.
Content-wise this video is great. Thanks for that. But I find it very hard to watch due to how you cut video fragments together. Almost every few seconds the image jumps. It drives me crazy. So imho there’s room for improvement 🙂
Yeah this is a really old video I have made many changes since then! Each video is a learning experience.
Take a look at UI customizer 🤗
3D printer in your BEDROOM is a BAD idea impo.
1. the fumes get into everything you are sleeping on.
2. microparticles of plastic land everywhere...
Sleep tight and healthy !!!
Take that thing out of your Bedroom..>
OR... put it in an enclusure with active ventilation to the outdoors.
Be well and happy 3D printing.
PL.
That isn't my bedroom. It is my office which is also the spare bedroom.
I don't think PLA outgassed harmful fumes. But an SLA printer is a different story ..
It will go in my basement when I finish it and move my office.
here a tip , when the printer isnt running ..........turn it off........you`re welcome .
That is what the smart plug does. It turns it off...