Cool rig, but Damn 124 bucks, I bit spendy imho. I could see maybe 100. I mean all the parts are just 3d printed plastic, if say the transmission portion and maybe the skid were aluminum sure 124-150 fair but... and like I say just my opinion.
Awesome I'm super excited to to build a few of the rat rod styles.maybe get some model kits and try some different parts and body's.very cool,super rad😅😊😊😊
DIY twin motor cable! 👍👍 Great build video. JOB well done as your trial and error will benefit everyone who gets this! @mofoRC should be thanking you AND @furitek with that radio/esc.
Another great build Adam, you're amazing don't know how you do it. Do you sleep? Fat big tires in the rear ,narrow smaller in the front,crome wheels, keep it blk,but rat it out (rust).
I wonder what material they used to print the SLA parts. The mofo website says it was printed at 12k. Early in the video I swear I could see layer lines and thought it was FDM printed. The motor mount already broke?!? I would rather just have them put the files on Cults3d. I'd be willing to pay for the STLs and I'll print it myself.
Just purchased. Looks great. Motor mount is questionable, material is kind of flimsy. Recommend some kind if reinforcement and using panhead screws for motor instead of the supplied ones which are tapered. Made some brass flat washers will see how they hold up. Maybe some kind of support for the motors as they are quite long.
I made my dual motor mount out of aluminum. I hadn't considered torque though, my reason was that 3D couldn't get the gear mesh correct consistently.. kept stripping out trans gears. The +/- 3D print accuracy at that time (3yrs ago) was not good enough. That said, i think 3D printers could do it with the right design.
Put the smaller swamp kings in the front and the bigger in the back two birds one stone lower gravity in the front and the smaller wheels will give more wheel speed I would think would be similar to an overdrive gear set
I have a question,I just installed my lizard pro and micro Komodo motor,when I turn it on the stock esc blinks red,but the steering and motor runs perfectly.How do I get the esc stop stop blinking?
I added some thick plastic washers to spread the load and so far it’s been ok thru 4 battery packs, time will tell. Maybe grafting 2 steel motor plates together? 🤔 the trans material seems a little soft and the bearings are a little sloppy. Might have to go back in with some CA.
Super cool looking, especially the double motors, but I ain't buying 3D printed stuff anymore. Every time I have it just falls apart. If they ever make this with solid materials I'll be grabbing one. Edit: Think smaller tires would look better. And I'd personally get something as low profile as possible, lean into the rat rod look.
It's cool, but the price is a bit much for 3d printed parts thar last 1 tumble 😂 Needs a bunch of overdrive and some smaller/skinnier tires in the front
DJCRAWLER 1 Inch Classic Vintage Beadlock Counterweight CNC Wheels Rim with Hex Adapter for SCX24 90081 AX24 TRX4M FMS FCX24 4WD 1/24 RC Car Universal Upgrade Accessories Parts (Silver) a.co/d/daNLi7R
Timestamps
What’s in the kit: 0:40
Transmission and motor assembly: 4:19
Chassis rails, skid, sliders: 6:52
Shock towers, battery and electronics trays: 8:25
Finished build: 10:36
Performance tests: 14:30
Indoor course runs: 15:43
Final thoughts: 21:54
Great build. The only thing this kit is missing for me would be a front grill and headlights like a true hot rod. Still, really cool looking!!
Definitely a unique rig. Can't go wrong with anything from mofo rc. Always very impressed with the quality of there products.
So happy you did this kit! I have been wanting to see it! Thanks!! Awesome killing it!
I'd run comp pins w/ white walls. Very unique kit!
Throwing deep super glossy black paint on that body would be sick, and then maybe stenciling some flames on the side
Love it. I've been wanting to build one but for pure speed performance.
Can’t wait to get it going with the twin buzzsaws!
Cool rig, but Damn 124 bucks, I bit spendy imho. I could see maybe 100. I mean all the parts are just 3d printed plastic, if say the transmission portion and maybe the skid were aluminum sure 124-150 fair but... and like I say just my opinion.
Awesome I'm super excited to to build a few of the rat rod styles.maybe get some model kits and try some different parts and body's.very cool,super rad😅😊😊😊
That’s awesome. Busted motor right after build. Is perfect lol
I think the proline super swampers would look rad on this thing.
What a cool kit
This is an AWESOME kit!! Didn't even know this existed!! I gotta' get one now!!
Rock Rat it is! Cool looking build!
Looks amazing, definitely need a Super swamper style tire
DIY twin motor cable! 👍👍 Great build video. JOB well done as your trial and error will benefit everyone who gets this! @mofoRC should be thanking you AND @furitek with that radio/esc.
I love it I’ve got one just ain’t tinkered with it yet. Still have to put it together. Appreciate you sharing the video that was super cool.
This "Thing" looks absolutely great ! 👍
Here from Jacob. Didn't know much about this stuff but... New sub 🎉🎉🎉
Dang that's friggin 11:40 cool!! 😎😎
😊What!!?? This is like a miniature actual car!? Looks like you've got that on an alignment machine! LoL
I am new here ... Like I know NOTHING about this. Oh my gosh... I'm rooting for the dang car to get up this hill LoL 😂😂😂 20:00
Another great build Adam, you're amazing don't know how you do it. Do you sleep? Fat big tires in the rear ,narrow smaller in the front,crome wheels, keep it blk,but rat it out (rust).
Rig looks fire, bro! 🔥🔥🔥
Very cool kit. ❤ thanks for showing
Awesome looking kit , pity the motor mount broke , that part needs refining . Thanks for posting this hot rod style build ....Harry
It’s a shame out runner motors are so small as two spinning away in the front would be cool.
I wonder what material they used to print the SLA parts. The mofo website says it was printed at 12k. Early in the video I swear I could see layer lines and thought it was FDM printed.
The motor mount already broke?!? I would rather just have them put the files on Cults3d. I'd be willing to pay for the STLs and I'll print it myself.
This reminds me of a Mud Drag rig. Needs big boggers in the rear and small boggers up front. High speed motors and and a flame paint job
Dual brushed motors! Now that's sweet. Wonder who's gonna pull off dual brushless outboard motors
Like the tires you have on it.
Different is always cool 😎
you should do like a smaller front/bigger back tire setup with some tires that are both available as a 57mm and a 64mm
Just purchased. Looks great. Motor mount is questionable, material is kind of flimsy. Recommend some kind if reinforcement and using panhead screws for motor instead of the supplied ones which are tapered. Made some brass flat washers will see how they hold up. Maybe some kind of support for the motors as they are quite long.
🤩 ich möchte das Teil haben.
Absolut genial 👍
Nice thanks for sharing and still hoping someone will do a nice formula off-road build
Buzz motors, rear motor mounts and overdrive the axial worm gears. Would love to see scxt24 24 basher for all my bashing needs!
I’m seeing swamp racer 😅 rocks bad; mud good 👍🏾
Maybe stock FCX24 Blazer Cooper tyres n rims on front and the biggest comp pins on rear? Cool kit, be nice to see it all painted up 👌
I wonder if you ran dual spur gears in a custom transmission with dual channels if you could run dig
All that torque I think they need to do an aluminum motor mount
💯 agree
I made my dual motor mount out of aluminum.
I hadn't considered torque though, my reason was that 3D couldn't get the gear mesh correct consistently.. kept stripping out trans gears.
The +/- 3D print accuracy at that time (3yrs ago) was not good enough.
That said, i think 3D printers could do it with the right design.
I wonder if you could fit some flex extensions on the front?
Insanely cool !! i am dropping over to mofo and picking one up if its in stock so cool !!!
i wonder if it could be modded to fit outrunners ?
old soup can cut up could make a cool looking hood shroud.
U need some mud slingers for the tires it would look sick with those tires
Will this work with the power wagon?
Sweet kit
I'm gonna make mine look like nuxs car from fury road
Put the smaller swamp kings in the front and the bigger in the back two birds one stone lower gravity in the front and the smaller wheels will give more wheel speed I would think would be similar to an overdrive gear set
I have a question,I just installed my lizard pro and micro Komodo motor,when I turn it on the stock esc blinks red,but the steering and motor runs perfectly.How do I get the esc stop stop blinking?
What is your go to battery upgrade for the scx24?
I like the Urgenix 450mah or 900mah
Will it work with the big block motors?
Most likely not bc of the size (I assume u mean like RCAWD 370 motor) bc yea those might fit but chances r they won’t
Tires you could for the build is dj-1214❤ i luv the look of them i have set🎉
RC4WD Scramblers? for the tires.
I think they’re Dj crawler tires
Does cape crawlers not have a discount code? Been trying to find any code to save some money but no luck.
Not at Mofo RC
Nice 👍🏻
Oh man I had this pulled up ready to buy until that motor mount broke. I was thinking being 3D printed might be a problem.
I so wish the motor mount was aluminum. It’s very thin and I can see it being a repetitive problem
I added some thick plastic washers to spread the load and so far it’s been ok thru 4 battery packs, time will tell. Maybe grafting 2 steel motor plates together? 🤔 the trans material seems a little soft and the bearings are a little sloppy. Might have to go back in with some CA.
cool
Super cool looking, especially the double motors, but I ain't buying 3D printed stuff anymore. Every time I have it just falls apart.
If they ever make this with solid materials I'll be grabbing one. Edit: Think smaller tires would look better. And I'd personally get something as low profile as possible, lean into the rat rod look.
It's cool, but the price is a bit much for 3d printed parts thar last 1 tumble 😂
Needs a bunch of overdrive and some smaller/skinnier tires in the front
dude your videos are cool as shit
This has been sold out on the website for weeks 😢
We have a few in stock
that looks mean
Wiked no luving it good content as always me its the motors must drain the battery quick 😢 appart from that it's a 😜🤪😝 ❤🤍💙
Nice.. too bad its out of stock :(
There is a few in stock
Honestly I don’t think it looks much like a rat rod and it seems like the performance isn’t very good so hard pass haha
Cool kit but not my cup of tea
Cool comment but don’t care
Paint it plz hate raw 3dprint bodys.
DJCRAWLER 1 Inch Classic Vintage Beadlock Counterweight CNC Wheels Rim with Hex Adapter for SCX24 90081 AX24 TRX4M FMS FCX24 4WD 1/24 RC Car Universal Upgrade Accessories Parts (Silver) a.co/d/daNLi7R
1:10
Don't like this at all sorry. Looks like a Walmart toy on clearance because pieces are missing
Rock Rat trx4m wen 🫣