@@tractorsmarinemechanic I can't say for certain, but this may be the 100% exact match (Equivalent) to 724070-51700 (Yanmar Injection Pump) on my 2qm15 engine
Hi I rebuilt mine too get some parts unstuck and now the tractor runs good but it leaks around the fittings at the top. Seems maybe the o ring is too rotted. Do you know what torque to tighten the top fittings or where to get a new oring? Thanks
Hi. I put the plunger back. I have been told that the plunger might be the reason why the pump doesn't inject . It has to be out back the correct way. Do you have a video that shows how to do it?
I Have a situation, my skid steer didn't turn on. The pump is very similar. Some suggestions!! THE diesel pressure is correct at the side of pump, but no pressure out of the pump. Any suggestions please
New subscriber sir..pinapanood q mga vids mo sir.gling mo mekaniko.. Ung father q sir may luma na L1801,ask q lng qng marami p b mbbli na spare parts nia..?
The thing for me is can the internals be changed around somehow to give full fuel to the left instead of the right on the moving rack. The governor on an MWM similar engine when started seems to snap to full throttle with the incorrect Bosch pump I located.
Do it man.your plunger maybe stuck up because of water inside your pump.you can fix it by metal polish.watch another video that I'm using with metal polish.clean your fuel tank and replace fuel filter.
Thank you.you can repair your own injection pump i knew you can do it by your ownself.do not send to the calibration center.they cannot calibrate that.the only they can do is to repair or replace plunger.thank you.
@@tractorsmarinemechanic iseki 2cyl Mitsubishi KE75 I subscribed and re cleaned injection pump using your videos...im getting fuel but need to check the timing I have no shims to adjust or don't know how?
@@lgvmobile same boat here, KE95. I thought there was supposed to be a big shim under the pump, but all I had was a gasket. Did you ever figure out how to set / check your timing?
@@tractorsmarinemechanic Thank you! We are taking about under the pump mounting flange? Where the pump mounts to the engine with 4 bolts? We are supposed to remove the old fiber gasket and install shims where there were no shims before?
This is possibly the most detailed video on these pumps that I ever saw.
Thanks so much.
Thank you for watching.pls.subscribe,like and share.thank you
@@tractorsmarinemechanic I can't say for certain, but this may be the 100% exact match (Equivalent) to 724070-51700 (Yanmar Injection Pump) on my 2qm15 engine
you repair very professional, ok.
Thank you for your complements.
Hi I rebuilt mine too get some parts unstuck and now the tractor runs good but it leaks around the fittings at the top. Seems maybe the o ring is too rotted. Do you know what torque to tighten the top fittings or where to get a new oring? Thanks
Does this pump pull out or is there linkage in the motor to disconnect first. Yanmar 2210. Looks to be the same pump.
Disconnect to cleaned the plungers
Hi . Thank you for that wonderful video. I did exactly as shown in the video . The pump still doesn't inject. What should I do? Thank you.
Just watched in follow what I did.do you also re assemble or replaced the plunger?
Hi. I put the plunger back. I have been told that the plunger might be the reason why the pump doesn't inject . It has to be out back the correct way. Do you have a video that shows how to do it?
I Have a situation, my skid steer didn't turn on. The pump is very similar. Some suggestions!! THE diesel pressure is correct at the side of pump, but no pressure out of the pump. Any suggestions please
Hello.
At 13:25 in the video with the 10mm screw with the blade on the right side what are we adjusting?
Підкажіть, будь ласка, помпи у z500 i zb600 взаємозамінні?
New subscriber sir..pinapanood q mga vids mo sir.gling mo mekaniko..
Ung father q sir may luma na L1801,ask q lng qng marami p b mbbli na spare parts nia..?
Ung partekular n part pki name para mkahap Tayo.
Is that long pin n the thing it goes into magentized
Just suction I believe..
The thing for me is can the internals be changed around somehow to give full fuel to the left instead of the right on the moving rack. The governor on an MWM similar engine when started seems to snap to full throttle with the incorrect Bosch pump I located.
If you change the internals which is the flunger. your engine will be wild or runaway
Thanks for reply I'll try again after watching your video!
Hello. What is professionality called a big spring for the pump. J wants to buy because the spring in my pump has brken.
The big spring is PLUNGER SPRING and the small one is DELIVERY VALVE SPRING
Pls subscribe to my channel,like and share.thank you sir
The big spring is PLUNGER SPRING and the small one is DELIVERY VALVE SPRING
Привет молодец чей насос
Thank you for sharing your knowledge
My pump has gotten water inside it and now it won’t pump diesel! Can I disassemble the top and clean all the parts and be ok?
Do it man.your plunger maybe stuck up because of water inside your pump.you can fix it by metal polish.watch another video that I'm using with metal polish.clean your fuel tank and replace fuel filter.
By the way thank you for watching.pls subscribe and share my video.
@@tractorsmarinemechanic Thank you for the fast response! I subscribed,liked and shared!
Thank you.you can repair your own injection pump i knew you can do it by your ownself.do not send to the calibration center.they cannot calibrate that.the only they can do is to repair or replace plunger.thank you.
@@tractorsmarinemechanic Ok. Thank you!! A new pump cost 600.00 U.S. Dollars and a rebuild is 500.00 but the pump looks simple!
Can you do a video on checking injection timing?
What kind of engine do have? Just subscribed and I show you someday.
@@tractorsmarinemechanic iseki 2cyl Mitsubishi KE75 I subscribed and re cleaned injection pump using your videos...im getting fuel but need to check the timing I have no shims to adjust or don't know how?
@@lgvmobile same boat here, KE95. I thought there was supposed to be a big shim under the pump, but all I had was a gasket. Did you ever figure out how to set / check your timing?
There are 3 shim under the injection pump and remove the gasket just put the shim only.
@@tractorsmarinemechanic Thank you! We are taking about under the pump mounting flange? Where the pump mounts to the engine with 4 bolts? We are supposed to remove the old fiber gasket and install shims where there were no shims before?
What’s the main cause for these pumps not pumping enough fuel? I have a 1110 Ford with Similar pump and it’s not pumping enough fuel on one side?
Thank you for watching.delivery valve maybe stuck-up or plunger need to replace.did you rebuild your pump or not?
@@tractorsmarinemechanic not yet I haven’t. I can’t seem to find parts for it
Thanks you
Кмз 012 подходит
Thank you for watching.keep subscribing