Exploring the ECU hardware and testing - Part 1 (Hardware circuit demonstration)
Вставка
- Опубліковано 12 тра 2018
- Video Link - Exploring the ECU hardware and testing - Part 2
• Exploring the ECU hard...
Exploring the ECU hardware and testing - Part 1
This video explains the ECU circuit board and demonstrates the way of crank and cam signal simulation to run the ECU and perform the different testing.
The engine ECU controls the injection of the fuel to the engine and the timing of the spark to ignite it. It determines the position of the rotation using a Crankshaft Position Sensor so that the injectors and ignition system are activated at precisely the correct time. It uses also number of sensor to read the status of the engine in order to run the engine at optimum performance.
The input to the ECU includes the following sensors:
Crank Position Sensor
Cam Position Sensor
Knock Sensor
Engine Coolant Temperature Sensor
Manifold Absolute Pressure or MAP Sensor
Mass Air Flow or MAF Sensor
Oxygen/O2/Lambda Sensor
Fuel Pressure Sensor
Engine Speed Sensor
Throttle Position Sensor
The output from the ECU includes the following devices:
Injectors
Throttle body control
Ignition coil
Load relay output
Malfunction lamp
Fuel pump
Idle control - Наука та технологія
This is a wonderful explanation and demonstration. You have demystified the inner workings of an ECU for me with the clear diagram shown and by pointing out the components on the real hardware. You also have an excellent method of explanation and teaching. Thank you.
You are very welcome, this is very good feedback.
مهندسنا الكبير سعود وطنك العربى اوى بمثل هذه الدروس وهذا لايقلل ابدا من شأنك ومكانتك العلميه التى نقدرها جميعا وفقكم الله وسدد خطاكم مهندسنا الكبير
حياك الله اخي الكريم، وشكرا لك على الملاحظة، كن على ثقة اني كذلك حريص عل ما ذكرت و هدفي الأساسي من اليوم الأول من فتح القناه هو المساهمة في اثراء المكتبة العربية اولا، اخي كل المقاطع عندي في القناة متوفرة باللغة العربية بلا استثناء و من ضمنها هذا الفيديو فنرجو تصفح القناه لإيجاد الفيديو العربي لهذا الموضوع. و في الحقيقة انا لا أرى ضرر ابدا من تبادل المعرفة باللغات الأخرى كذلك.
Your explanation is simple and easy to understand. Please make more videos on ECU and Transmission Control Module.
Thanks for positive feedback, I will try my best.
Excellent brother. Great learning classes!
Thanks for your positive feedback.
Great Job !
I also repair ecu for mitsubishi and also planning to build this kind of simulating circuit to test if repair of ecu was successful without the actual efi engine.
I'm happy that my planned design was almost same with your ecu tester.... These confirm that my planned circuit will work. Thanks for sharing....Saud.
+Roger Sy
You are mostly welcome Roger, yes ur right the simulating device is very useful it enables to confirm at least the ECU is accepting the basic inputs then processing and generating the outputs, anyway hopping all the best for you. Thanks
Very informative and learned a lot for a beginner like me. Keep up and produce more videos like this.
Very welcome.
بارك الله فيك وجزاك خيرا
Thanks for sharing ECU world.
Welcome 👍
الله يرضى عنك ويوفقك
Enjoyable & informative!
P.S. Great 🎥 work.
👍😎
You are very welcome 👍
thank you for the uploaded video, good luck always and always healthy greetings from Indonesia
You are very welcome, thanks for feedback
This is what I am looking for, thanks.
You are very welcome.
الله يسلمك على الشرح السهل و المميز.
اهلا وسهلا فيك اخي.
good video thanks
Ohh man your top notch best video ever I have seen in nice explaining thanks for sharing
You are most welcome, thanks for feedback .👍
very clear demonstration
👍
great, you really understand how te ECU work
👍Thanks.
thanks master saud very nice Explanation
You are most welcome 👍
Thank sir for well explained video and to the point. god bless you and salam.
Please don't stop making fantastic videos like this........
Thanks very much fo positive feedback.
Thank you master for your tutorial.
I will follow you till I can self practical. 🙏🙏🙏🙏
Thanks for your interest to learn and development, for sure as long you have the self driver and willing to know you can reach.
best explanation about ecu working
👍Thanks.
It's a pleasure to watch' your vedios thank you.its give an idea thank you very much
You are very welcome.
thank you sir, your explanation is very good.
Thanks 👍
Thanks for the presentation. I have an ECU problem of mazda zx 5. The ECU"s circuit got burnt due to a fault in a sensor's terminal to the extent that the processor got spoilt. Please advice...
Good teaching
Oh men why are you thanking us we should thank you for this experiment too good dude 👌 men 💯
Most welcome my dear friend ,
Yes thanks for good feedback. 😊
Great explanation thanks sir
You are very welcome.
Thanks
thank you bro, very informative video. May I ask if you have a pdf doc. about repairing ECM?
My Peugeot partner 20hdi 2004 crankshaft sensor keeps failing where can I have the ECU tested please help thanks
Thanks.
Please tell me what the black bolt in the middle of the cover ecu? air flow or what this....
Hi, car a plug & play be repaired? Thank you for your reply
Very good information. Could you do a video using a scope and logic probe, then look at signals through a microcontroller board. Data, Address, Control lines and show some common fault conditions like a data line being held low. Other examples of faults would be good as well.
Thank you for your videos and the best to you in 2020.
Thanks for good feedback,
In fact that vedio is already available in my channel, which is covering troubleshooting microprocessors and microcontroller circuits in details.
Please check the following title
(Advance troubleshooting of microprocessor and microcontroller circuits using oscilloscope.)
Thanks for yuo this vedew vary good thankyuo
👍👍Most welcome
Hello, and thank you for the video, it’s excellent and informative. I have a 2012 Volkswagen, the multimedia radio, the interior light and the sunroof no longer work but everything else works perfectly. The diagnosis tells me there is a control module fault with the code: 1048642. How can I repair this fault? Is it the soft out The hardware that is at fault? Thanks a lot for your help.
Hallo friend Could you please explain me the errors message displayed on my SAM afet dg shatdown : ⠀
Say sensor again.....love it
Master, tell me how to make an ECU simulator for the electronic circuit wiring, thank you
My Audi A4 got a light bump when it rolled down a hill with the ignition off and struck a wall, scratching the paint work
But now the central locking doesn't work and the immobilizer flashing light on the door has stopped working.
I now must use the key to open the door but the car operates fine otherwise, except dash shows that the boot is open since the accident. .. which of course it isn't.
How could I repair that?
Thanks sir
O my good nice video 👏👏👏
Thanks for your good feedback.
Please ford 150 ecu how check it and not showing check light
Thanks brother
You are very welcome.
Assalamoualaikoum. I have a burnt ECU for Audi A6 allroad. Do you offer repairs service?
Ma sha Allah Good job
Thanks for feedback.
Well explained Arbab .. hayak Allah
Thanks 👍
Nice
Excellent sir where can i go for a training course on ecu repairing?
do you have port pin out ? thanks
Good day sir im from philippines im interested to repair ecu what books i must read
thanks nice lessons please do more videos programming chip and tunings
Thanks, I will try my best.
hallo sir. can i send my ecu to your shop to repair? my mechanic says my ecu didn't send power to my nozzle to pump out fuel. i can't fired my car. they've already check the fuel pump and scan everything was fine.
Thank you for your video, I'm interested.
My car Toyota Passo 2006 have a problem with immoboliser as the light was sometimes blinking
or unable to start. I need some help cos we don't have any dealer in my country Kiribati.
Is it possible to change an ecu with a non-immobolised type?
You are very welcome,
There is different ways to deal with this, but first step don't forget to try start by spare key if you have.
1-Try to reset the ECU, by erasing the eeprom data you will need at least some eeprom programmer to do this, then after that you need to register the key again by following key registration procedures you can serch for the procedure forms the web based on your car modle.
2-If you suspect the ECU is defictive, then you can try to clone the eeprom on new ECU, just by removing the eeprom (this is ic with 8 pins) from faulty ECU and use it to replace the same eeprom at new ECU.
3- try to do immobilizer off or delete but you will need programmer and some computer application to do this.
All the best
Hello Sir i need
f6a t/c 2wd 4at
33920-74G8 1denso ecm pinout wiring diagram plz
how can i buy crank and cam simulation , electro mechanical bord with equipment
Mashallah excellent bro
Thanks 👍👍
i do have a question, when you are simulating cam and crank signals, i know that before the pcm will work the injectors and ignition, it will be looking for specific patterns of the crank and cam, and how they are synced. how are you accomplishing this/ THANK YOU.
Hi,
Your point is very valid and correct, in fact what I think in this type of simulation the ECU hardware and program is just reacting to the input signal and not genarating timed output, it keeps trying to adjust the output all the time , this semulation signal is at low RPM and the ECU is not fully functioning and in fact this helping us just to get the output and check the ECU respond, not only that but we can get the injector and ignition output only by providing the crank signal alone without cam signal and also it is giving the output eventhogh the immobilizer is not disabled,
I know if you use a semulation device like MST 9000 the ECU generates more timed output signal.
Hello can you repair continental getrag dc4 tcm
I love your videos. I am interested in tutorials on ecu repair for Mercedes actross trucks
👍Thanks for good feedback.
good day Mr. Saud
I'm very admire the creativity of your testing platform
is it ok to ask what or how is the crank & cam generator work?
Hi, good day for you as well and welcome for any question.👍
In fact the one I am using is based on costomized mechanical mechanisms plus some electronics to condition the signals.
This type of simulators can be built based on different principles, it can be pulse genarate circuit using 555 timer ic for example or other circuits.
@@saudautomation
if possible i would love to try your method!
im very impressed by the simplicity of it
LOVE YOUR CONTENT !!!!!
hi, from ECU's connection diagram in your video, i didn't see connection from immobilizer, in many car equipped with immo, if we try to turn on / ignition the car with 'foreign' key, the car will not send data from immo to ECU, so the car will not start. Is that true? or you have the different opinion, please explain it to me..thanks
Hi,
Thanks for the good point.
The inputs provided in the diagram was example of basic parameters to ECU as simplified schetch only.
Indeed you are right immobilizer system is one of inputs to ECU this can be external transponder ECU in some designs or integrated in the ECU, if non authorized key used then received security code will mismatch to the one saved in ECU eeprom and engine won't start.
In fact there is other inputs also like status of gear if neutral or park, brake padle pressed status, IGF for ignition feedback in some cases.
I found an exploded capacitor in mine. At this point, I have to guess it was one of two used as smoothing capacitors, mabe even a backup. Someone had replaced two of them and reversed polarity on one. It was a low voltage cap. As it didnt affect anything, my guess is it might be for OBD2 power supply or something none critical.
nice and informative video, plz make more video on ecu
Welcome 👍
@@saudautomation nice video do you give any training programmes if available please sent me your contact details or you can write me Modoucamara106@gmail.com thank you
😊Thanks.
@@modoucamara1301
Your most welcome. Thanks
Thank you sir for this video... (request) aircondition ecu function?
Thanks and very welcome,
Sure I will try in future.
thank you man. go head
👍Most welcome.
Hi I have an ECU for ssangyong rexton year 2004 I need to repair how can I do
Or can I you find me an used ECU to replace?
Hi
My hiace cannot start cos ecu s got problem. Now we odered for a new one from Japan on Mei, untill now there is no news when it will come to Malaysia.
So is it true, it only from Japan, or we can repair it. Can you give any suggestion to fix the poroblem.
My hiace manufactured year 2013
Cc 2.8 and patrol fuel.
Hopping you help me, please
Hi,
I believe you can discuss with your dealer about this,
Repairing is normally possible but depending on the failure so not every fault is repairable, as long you already ordered new ECU then that's fine always new ECU is more reliable at all the cases compared to repaird one.
sir I am one of your subscriber her in Philippine. You have a great video. Can I send my ECU for testing and repair. It has no com when scanned. The vehicle was partially flooded, but we already clean every sensor and necessaru parts. At first it start and engine run but after several days it just crank and no start.
thank you so much! where r u based? I need to get my ECU checked, cleaned and capacitors replaced.
You are most welcome, I am from Oman.
You're awesome!
My ecu got corroded BAD and one of the ic chips was ruined to the point that one of the legs just crumbled off! I can't find any info on what the chip does. None of the numbers pull up anything when I Google any combination of them!
Take multimeter and check the voltage of the one of the ic similar to that ic which is ruined then check the reading and start exploring which ic has the same reading and detach the ic from the other chip then installed the chip into your mother board simple 🔥
Where is the igniter driver on a md354635 ecu
Thanks sair if you please what car ecu you are working
This was for Mitsubishi Lancer engine control unit.
How to make this devise
I have doubt that i am using a obd scanner (ELM327) for diagnostics of car. Which can send errors to my mobile via bluetooth.
its a very cheap one and i don't know whether the acuracy of its operation.
The question is. Will it affect to ECU Put into dawn or lower performance.
No worries technically the ECU is not affected by the connected scanner unless the change is commanded by the scanner operator or it can be ECU hacking activity, regardles cheap or expensive scanner.
Please sir how can I get that device you develop the give the Crank signals
Hi you are very welcome,
Thanks for your interest, but this a prototype developed for my own use.
Sir,Your all tutorials are full of knowledge like you are giving a Hadia of Zahab!!!!!!
I have a question, that on any ckt weather it is a control unit or bcm,how I will came to know that this particular portion is faulty.Do i have to go step by step stage wise, like to check any convention ckt. Apart from getting the fault code. your keen advise is required.
Hi,
Depending on the failure mode and fault different troubleshooting approach and technique can be flawed, I for example the complete unit is dead and not responding then I can start to check the supply voltage and the healthness of main microcontroller, but if two or three outputs are not working then I check what is the common component meeting them and replace if required,
If one output is no working I start tracing from that output pin going down I keep checking all the components on the way until I get the faulty one. Some test I need to keep the unit off powered and sometime it should be powered on depending.
please master for the circuit schematic for the ac simulator test kit, I hope the master is always healthy
Asalamulaikum.
Sir, I have qustion.
How to identity eeprom in the car ecu......?
Alaikum Aslaam,
eeprom you can find it normally close to the microcontroller it's 8 pins ic with part number it can be either 93Cxx, 24cxx, LRxx or RAxx ... etc.
Not all ECU's using external eeprom sometime this is embedded in the microcontroller.
Interesting. I would love such a setup to use on BMW ECUs but how would one deal with immobilizer ?
Hi, thanks for feedback.
Yes the immobilizer part is challengeable not only BMW but most of other cars, some time like number of Toyota ECU's they require ignitor confirmation feadback (IGF) signal and ECU will not also respond without it. All this permissives signals sometime they make difference and sometime not.
@@saudautomation I'm using an
EWS deleted/ immobilizer bypassed ECU for a BMW z3. Sometimes it fires ignition, sometimes not... I just read what you wrote about ignitor confirmation...and wondered if it's happening here.? Car is 2000, so twenty years old, maybe they didn't have it then? Anyway... intermittent behaviors are always hardest, aren't they, lol?! Maybe has to do with 5v being ok on air temp sensor but 12v is read on mass air sensor and also on coolant temp sensor?! Seems sensors would all be 5v? Such an interesting world...lol.
What is the orange vertical component t 4:10 in this video? Upper left part of the ECM board near the 5v power transistor. This component appears damaged (overheated?) on my ECM.
Hi,
Yes that component normally called (hybrid integrated circuit) so it contains IC plus some other parts forming small circuit board packed in ceramic.
@@saudautomation Thank you for that info. I have some numbers off of it, but have not been able to find any source for this. Do you have any recommendation as to where I should look for this component?
Yes this are very costomized components and not easy to get unless you have the detailed part number, try try to communicate with the car agency if they will help.
@@saudautomation Understood. I have sourced a used ECM that will make my truck run smoothly, but it is for a 6 cyl version of my 4 cylinder engine. I put it in today, and it ran pretty well (they both use inline Fuel Injection pumps, so I don't have to worry about 6 vs 4 cylinders). The boards and pinout are the same, but with the replacement ECM in, it runs at about twice the speed it should at idle (I think the gear that the speed sensor senses is a different size). I don't have Schematics, but I do have all the pinout and the functions of each connector pin. Could I correspond with you to see if I could find a way to solve my problem? Perhaps by email? I have recently purchased a power supply, oscilloscope, and have a diesel engine simulator arriving soon. Thx!!
Very very nice and educatioanl,, thank you my friend for sharing your knowledge, bless you more,,
Just want ask how you made your ecu, ckp,cam signal simulator??? Do you have a diagram or a video how you made it
Thanks so much more powee mu friend
Hi,
Very welcome and thanks for feedback.
Regarding the ckp, cam semulator device, most of work is done by mechanical mechanism , the electronic part is only conditioning the signa, beside this is still under development.
@@saudautomation hi ,can you send me an diagram for this my friend if its ok to you,, thank you very much
@@saudautomation this is my email joelsarmientoaresgado@gmail.com
Masha Allah
Thanks
Hi, I would like to do a complete course with you, is it possible and how is it possible?
Hi, and thanks for your interest,
In fact I don't do any courses, just the avaliable vedios in the channel.
Hi sir, could you please tell me where i can download or buy schematic circuit diagram for ecus
Hi,
If you mean ECU pinout then sometimes you can just search for ECU part number at the web,
Or try free software like Carmina std available, Alldata software is paid professional software.
But if you mean electronics board circuit diagram that's not easy.
Hi,
If you mean ECU pinout then sometimes you can just search for ECU part number at the web,
Or try free software like Carmin std available, Alldata software is paid professional software.
But if you mean electronics board circuit diagram that's not easy.
Hello sir pls do you train people ?? Am interested to learn it
Hello, thanks for your interest to learn more, currently I just exchange knowledge through the vedios.
assalamualaikum
from where can i learn about ecu
please guide me
AlaikumAslaam,
Through basic electronics plus continuous practice and hands-on.
Sir may I know if a pcm,bcm,ecm are integrated into one computer box? Forgive me for my ignorance coz I don't have any training in electronics school.tnx sir
Hi,
ECM (engine control module) and ECU (engine control unit) they do the same reading the sensors and controlling the engine.
PCM ( powertrain control module) combine the engine control and transmission control in one unit.
@@saudautomation Tnx sir for that information
❤
Wow
nissan accent2010 ecu coil driver how test demo
Hello sir I'm from India
حياك الله
حياك الله، واهلا بك.
Hello, is it possible I send you my Jaguar S-Type 2004 ECU unit you look at it, and possibly repair it for me.??
Hello, we can communicate through email
saudautomation@gmail.com
The link under video i cant c it pliz
It is there, at the vedio description.
Are you selling that sample circuit device sir ? I'm very much interested
This not yet for sell, but you can build one to generate the pulses for example using 555 timer ic.
Hope I can buy that if sale it
Assalamualaikum Sir 👍
From India 🇮🇳🇮🇳🇮🇳
Hi,
Very welcome 👍
sir can you help , your testing device , or how make this board testing device
Hi, thanks for your interest, you can develop one using 5555 timer chip to generate required pulse.
How can I make it? Where is it found?
master
Thanks, you're welcome.
Ya Saikh, how do you learn all of this? In my country, Indonesia, so many people have trouble with ECU, especially car from 2010. I really want to learn this to help people solve this issue
Hi,
I learned through reading and contenuse practicing, of course every one can learn and gain good experience start with simple troubleshooting and never givup.