TRANSCRIPT: Older remotes: right button says “Reverse”, newer remotes have “Speed”. Same meaning below, i.e. “right (not Power) button. “Throttle” means “thumb wheel” below. On/off: long press power button Change forward speed: short press Speed button. Cycles through Lo, Mid, Hi, Pro. Pro has same top speed as Hi with stronger braking & acceleration. Change braking speed: hold throttle in “brake” position then cycle through options with Speed button. Reverse: press Power button twice. Lower left changes from FW (“forwards”) to BW (“backwards”). Cruise control: single press Power button while in motion - when throttle is released the board continues at the set speed until the rider accelerates or decelerates again. Hidden menu Turn remote off then long press both buttons simultaneously until it turns on. On S, only 2 options appear. Use throttle to change speed units from MPH to KM/H. Press Speed button to move to Wheel Speed settings. Use throttle to change number. For Endeavour S, 8 inch wheel has speed of 80 & 7 inch is speed 65. Use Power button again to exit the hidden menu.
Hi, I’ve bought a board from propel ev and it arrived five days ago. I drove it twice. The first time I drove about 2/3 kilometres and the battery died without any warnings, I thought it was because I didn’t charge it when it arrived, so I put it on the charger for like five hours. Today I decided to drive again but unfortunately the battery died again after just 3/4 kilometres again without any warnings. It’s a little cold outside but it’s not under the zero. What is the problem and what should I do now? It’s pivot gt 2in1
I have the Pivot S 2-in-1. What are the wheel speed numbers I should put on the hidden menu for the street wheels and the all-terrain wheels? So my speed and mileage numbers are correct.
Thanks for this video, I could not figure out how to change the brake level until I watched it. On my new 2S there is a "frequency" option in the secret menu. What is the purpose of this?
Hey There I just got the Endeavor2 GT and i dont see how the front lights turn on? they say with the remote but there is nothing on the remote nor the hidden menu Help!!! thxs
Hi there. Not sure if anyone answered your question. I have the same board. Just press and hold (3 seconds) the button on the right; it says ""reverse", but if you hold it, it will turn the lights on. I hope that helps. -Gru
HI , i have s2 almost brand new , when i accelerate with the board with fully charged battery , 2 or 3 lines from the battery go away until i slow down . is that normal ? . thanks for answering me
Hi ! Thanks for this video, makes everything clear on how to use the ling yi Remote, just one additional setting in the hidden menu of the Endeavor 2 S, it shows a 3rd option "FRECUENCY", what difference it makes to change it ?? regards
Hi. Can i change to 99 wheel speed on endeavor s. 8’? If not, why???! On 80 WS I have 51 km speed. On 99 it 63 km speed. I am not tested it on roar yet👌 Best regards!
You can, follow the link below to learn how to find the hidden menu. For an S I believe it should be set at 85 or 87, I'll get clarity tonight. Just know, all that does is sync you mileage and speed to be realistic, you wont hurt anything changing it I'll get exact # for you tonight ua-cam.com/video/xDTCLKkwxT0/v-deo.html
Sorry everyone. I forgot an important part and had to edit and reload. I lost a few of the replies. Please reply again and I'll be happy to answer your questions
Hi Russ, You & your channels 411 are very helpful. I received my Propel Endeavor about a week ago. 1st ride worked fine, went about a mile. When I came out of a store, It would not work. I had fully charged the remote & board. The power 🔋 bottom is always on? It turns off with remote--for 3 seconds then comes back on. How do I defrag & reboot- or? Please help! Going nuts, want to go for a ride. Hope to hear from you soon. 👍 Sssss model
I noticed that when I go downhill I can’t decrease the brake pressure. I can only release them. I don’t have issues on flat surfaces. For example, going downhill If I brake 80%, then I release them a little to 60% nothing changes it is still at 80%. If I release them to 0% then I can apply 60%. Any idea how to fix this?
Hi Russ, I was just wondering what the wheel speed option is for? And/or how it works. I also have the stock 8 inch wheels, so I guess I'll take your word for it and set it to 80.
These are preset from the factory. Only time youd change it is if you changed tire size. This cant hurt you or anything, its just a number to let the esc know what size tire youre using for tracking mileage accurately
@@propelvirtualgarage963Hello again, coming back to you a couple months later because after playing around with propel's 7" tires I started to wonder if I could get my hands on tires larger than 8" for the endeavor. I tried looking myself online but never found anything. Would you happen to know anywhere I could find such a thing?
Very helpful. Just got an Endeavor 2GT. The wheel speed with 8" tires from the factory is set at 73.......is this correct, or should it be 80?
TRANSCRIPT:
Older remotes: right button says “Reverse”, newer remotes have “Speed”. Same meaning below, i.e. “right (not Power) button.
“Throttle” means “thumb wheel” below.
On/off: long press power button
Change forward speed: short press Speed button. Cycles through Lo, Mid, Hi, Pro. Pro has same top speed as Hi with stronger braking & acceleration.
Change braking speed: hold throttle in “brake” position then cycle through options with Speed button.
Reverse: press Power button twice. Lower left changes from FW (“forwards”) to BW (“backwards”).
Cruise control: single press Power button while in motion - when throttle is released the board continues at the set speed until the rider accelerates or decelerates again.
Hidden menu
Turn remote off then long press both buttons simultaneously until it turns on.
On S, only 2 options appear. Use throttle to change speed units from MPH to KM/H.
Press Speed button to move to Wheel Speed settings. Use throttle to change number.
For Endeavour S, 8 inch wheel has speed of 80 & 7 inch is speed 65.
Use Power button again to exit the hidden menu.
Hi, I’ve bought a board from propel ev and it arrived five days ago. I drove it twice. The first time I drove about 2/3 kilometres and the battery died without any warnings, I thought it was because I didn’t charge it when it arrived, so I put it on the charger for like five hours. Today I decided to drive again but unfortunately the battery died again after just 3/4 kilometres again without any warnings. It’s a little cold outside but it’s not under the zero. What is the problem and what should I do now? It’s pivot gt 2in1
Link to video for the Color Screen Remote?
I have the Pivot S 2-in-1. What are the wheel speed numbers I should put on the hidden menu for the street wheels and the all-terrain wheels? So my speed and mileage numbers are correct.
So if 8” is 80 and 7” is 65 would that mean 6” would be 50?
Can you do the same for the pro, my board un-paired and I can't get it to reconnect 😵
Same happened to me, how did you resolve this issue ?
@@condor7782 my receiver was dead, propel sent me a new one, for free, and I was over the warranty time, I only have to pay shipping 30$
@@jayd8350 Thanks for the 411 Jay D, did you call them ?
I can't find a #.
I did send them an email.
Thanks again.
Thanks for this video, I could not figure out how to change the brake level until I watched it.
On my new 2S there is a "frequency" option in the secret menu. What is the purpose of this?
Hey There
I just got the Endeavor2 GT and i dont see how the front lights turn on? they say with the remote but there is nothing on the remote nor the hidden menu
Help!!!
thxs
Hi there. Not sure if anyone answered your question. I have the same board. Just press and hold (3 seconds) the button on the right; it says ""reverse", but if you hold it, it will turn the lights on. I hope that helps.
-Gru
Thanks, i was just looking for this@@josebutt-seco2680
HI , i have s2 almost brand new , when i accelerate with the board with fully charged battery , 2 or 3 lines from the battery go away until i slow down .
is that normal ? . thanks for answering me
Yes, totally normal
Can someone tell me how to control the damn lights on the endeavour 2 GT
Hold down the speed (right button) for 2-3 seconds). Same thing to turn them back off.
Hi ! Thanks for this video, makes everything clear on how to use the ling yi Remote, just one additional setting in the hidden menu of the Endeavor 2 S, it shows a 3rd option "FRECUENCY", what difference it makes to change it ?? regards
Do not change that, its the frequency your remote works on, leave at factory setting
Hi. Can i change to 99 wheel speed on endeavor s. 8’? If not, why???!
On 80 WS I have 51 km speed. On 99 it 63 km speed. I am not tested it on roar yet👌
Best regards!
You can, follow the link below to learn how to find the hidden menu. For an S I believe it should be set at 85 or 87, I'll get clarity tonight.
Just know, all that does is sync you mileage and speed to be realistic, you wont hurt anything changing it
I'll get exact # for you tonight
ua-cam.com/video/xDTCLKkwxT0/v-deo.html
Sorry everyone. I forgot an important part and had to edit and reload. I lost a few of the replies. Please reply again and I'll be happy to answer your questions
What are the wheel speed numbers for the Pivot S?
Hi Russ,
You & your channels 411 are very helpful.
I received my Propel Endeavor
about a week ago. 1st ride worked fine, went about a mile. When
I came out of a store, It would not work. I had fully charged the remote & board.
The power 🔋 bottom is always on?
It turns off with remote--for 3 seconds then comes back on.
How do I defrag & reboot- or?
Please help!
Going nuts, want to go for a ride.
Hope to hear from you soon.
👍
Sssss model
Please send this info to services@ridepropel.com and we'll get you sorted asap
Hello propel this is Devin. I have my propel endeavor that I have only ridden 200 miles on and it already stopped charging and won’t turn on.
H Devon, please contact services@ridepropel.com and we will get a tech to help figure out whats up.
Whats the wheel speed in the hidden menu of the x4s?
what are the chances this pairs with an older hobbywing esc?
O% This is a lingyi esc/remote
I noticed that when I go downhill I can’t decrease the brake pressure. I can only release them. I don’t have issues on flat surfaces.
For example, going downhill If I brake 80%, then I release them a little to 60% nothing changes it is still at 80%. If I release them to 0% then I can apply 60%.
Any idea how to fix this?
What is your email, I'll have one of the tech reach out to you. Also, is this a Pro or an S?
@@propelvirtualgarage963 thanks its an S. I've emailed support. Dont want to post my email publically.
Hi Russ, I was just wondering what the wheel speed option is for? And/or how it works. I also have the stock 8 inch wheels, so I guess I'll take your word for it and set it to 80.
These are preset from the factory. Only time youd change it is if you changed tire size. This cant hurt you or anything, its just a number to let the esc know what size tire youre using for tracking mileage accurately
@@propelvirtualgarage963Hello again, coming back to you a couple months later because after playing around with propel's 7" tires I started to wonder if I could get my hands on tires larger than 8" for the endeavor. I tried looking myself online but never found anything. Would you happen to know anywhere I could find such a thing?
The controller is so uncomfortable
Thats one we dont hear very often. Most riders enjoy the size and shape of the lingy remote
Hi, Just received endeavor S. How do I reverse? Tried it on remote, not seem to be working.
Press left button twice
All set?