Build a Off Road Mini BUGGY using Engine 163cc - 4 Speed
Вставка
- Опубліковано 21 сер 2021
- Hello my dear friends, in this video I'm going to show you.Build a Off Road Mini BUGGY using Engine 163cc - 4 Speed. Thank you for watching!! Please subscribe to my channel.!
Thank you for watching your video. Please share your video to support me!
Love all of you :)
----------------------------------------------------------------------------
© Copyright by KST HACKS ☞ Do not Reup
----------------------------------------------------------------------------
#KSTHACKS #buildbuggypubg #diybuggy - Навчання та стиль
Am I the only one who was impressed with the home made hydraulic press??
This is important.... Read carefully... In this project, there is a great need for structural reinforcements in the front suspension, because of the way this part of the chassis was manufactured, the cuts made in the bars to bend it , compromised its final structure. The parts to be reinforced are between the swingarms, in this place add a whole vertical bar (no cuts) welded from the bottom part (Bar) to the topmost part, after adding crossbars between the bottom bar to the middle bar, and from the middle to the top bar, forming a horizontal V ( ◀️), weld a support between the middle bar (where the upper swingarm supports are welded) to the added central reinforcement bar, this will distribute the forces applied on these three points (on these bars), instead of only applying force to the middle bar, thus preventing it from bending and breaking... The reinforcement of the middle bar where the swing arms are installed, even the central column is not for because of the force applied to the suspension, and yes because of the welded bar at the end of it (Bar not curved in a single piece (pipe)), compromising the structure of this bar of the upper swing arm... Another very necessary alteration that you will have to make the structural reinforcements, it is the shock absorber support arms, which are at a serious risk of breaking, add a cross bar between the shock absorber support bar to the middle bar of the chassis (where the upper swing arms are located) , this will avoid a great effort in these parts of the chassis, and their breakage, it is vital that their reinforcement be done, to avoid this big problems in the future (The breakage of these structures could cause the overturning)... The last reinforcement but not least , it would be to add a crosspiece (A lock) on the chassis between the upper bars that are attached to the shock absorber supports (from the right to the left side), this will prevent the chassis from twisting in the future (warping, bending, or twisting) ... These problems, if not corrected, could cause the "Mini Car" to overturn and cause serious accidents with serious injuries.
Добрый день! Креативность, конечно, на высоте, но... Боюсь, что вы больше будете ремонтировать этот автомобиль, чем ездить на нём. И самое главное - никогда не крепите рулевые механизмы на сварку, это недопустимо!
Ang galing mo ok Yan Ang Ganda, I believe in you woow, The Best ka,,
Mantap. Slamat. Chukcest
Не плохо получилось, но транспорт одноразовый. Ремонту не подлежит, да и ездить на нем опасно.
فل فیل ویڈیو
This thing is a complete deathtrap, it won't be long before somebody is severely injured through it, It's an extremely good attempt but Completely under Simplified, Structural integrity is off the chart..
Keren anda sangat kreatip
I fear the universal joints are at an extreme angle but the creativity is great.
gawang pinoy. good job kaibigan galing
👍👍👍👍👍❤️❤️❤️👍🙏
Mantap
I really like to see this buggy with highpowered 4x4 eletric hub motors! :D
YES!!!
@@donlorinsharp Absolutely!!!
What an awesome project
This guy built a gear box out of scrap parts out of a box ……. Tony stark.
it´s is music ????,, belo trabalho .AMAZING
A joy to see every minute !
Perfect
Um grande abraço
17:38 the legendary technique
A grinder and paint makes me the welder I ain't
😂😂
Amazing BUGGY
Me:“Oooo is dat a rock?”
God: Yea
good morning. Oh! Amazing and cool is fine!😆👍️ But, da ho!😆
Ban chế tác rất hay nhưng có một điều đáng lưu ý là trục dẫn động sau không có khớp thay đổi độ dài ngắn của trục một khi bánh xe nhún lên xuống trục này sẽ gãy đó là chỗ chưa hợp lí
Adorei seu projeto só uma observação faltou colocar o assoalho para os pés más parabéns vc e ninja abraço amigo
grind the galvanized coating off before welding ,better welds and less poison in your lungs,if that's a concern at all.
Cảm ơn bạn đã chia sẻ
I am afraid your suspension will tear the bearing apart there is no travel in the connection, from back suspension to engine ...
tracking is spot on... errrr ish
Quá đỉnh
Parabéns só o que posso dizer no momento continue sempre.
Parabéns sucessos
Предлагаю скинуться пацану на трубогиб!!! 😉
This is awesome and the fact is mostly handmade aside from the mechanical flaws i love it
W
Rapais vc é um gênio fazer caicha de transmissão de ré
Top
What about them county orange slippers! he had on them Bruce Lee Roy's
Amazing super good
Oh thanks
Amazing what this man does with an angle grinder and electric arc welder!
Thanks for watching!
And a big brain
And it only took him an hour and a half. I couldn't even begin to understand what all he done especially when he built that transmission and that blew me away.
@@glbaker5595the video was sped up like x2 so more like 3-4 hours on a buggy that has such shitty welds, thin metal, and bad design, that it wouldn’t even be able to handle a speed bump.
Buen trabajo 👍
👍👍👍👍👍👏👏👏👏👏👏
It must took you months to build this highly engineered kart you should put bigger wheels on it and race it Good Job!!
thanks you
Deus abençoe Tudo de bom
Top show parabéns 👏🇧🇷🇨🇮
Toptop
Awesome build!! But maybe invest in a tig welder, or even mig Welder 👍
Mantul Bosqu
Great job ,you can build your shop for full time business . 👍👍
The front part of the Oscillating Arms are the ones that run the most serious risk of failure... Mainly because of the welding on the intermediate tube and the half-cut arcs to be curved. The suspension forces applied at this point are the most vulnerable and subject to breakage due to the welding of this tube (It is not the only curved tube). The front arches will be the first to fail because of their compromised structure, they will not be able to absorb and distribute the forces applied at this point of the chassis.... Unfortunately in this case this curved structure is only for aesthetics (an ornament). on the chassis. It will cause serious problems in the future if these errors are not corrected. A way to avoid breakage at these points would be to add a Triangle in this front part of the intermediate tube, canceling the forces applied to the arches, a Straight Tube welded between the intermediate tubes on the left and right, and a reinforcement in V between these intermediate tubes to the lower front tube of the lower swingarm reinforcement, this would distribute the suspension forces more efficiently, and avoid the previously mentioned problems with the front arches. I know this is a Mini Car and not an ATV, but with a few upgrades it could become a low cost one. Learning in this case making your own mini Car is most important in this story. Good job, hope I helped in some way.
เก่งมาก
Legend say till now those bearings still weldered
Good work & good hand
This guy makes me feel less weird for welding in sandals. I knew there were more of us out there.
Wait till you have a good sized ember burn thru your shorts into your little johnny then you will be a little more careful haha not fun 🤣
great music
Muito massa 👏👏👏👏👏
you need to add adjustment to all of these chains for when they stretch
Là on a affaire à un génie et non un bricoleur du dimanche !😎🙀
Need to lower the suspension so the angles of the arms are not so sharp at ride height.
Mama will be angry..since you've stained the house specially guest room. He bro. go and make her satisfied , happy and pleased.
Follower from H.K.J
,,, ALWAYS BE HAPPY,,
Нет стабилизатора на передней подвеске.На скоростных виражах не заваливается?
И как вибро нагрузки на больших оборотах и скоростях?Просто Я посмотрел,что центровка выполнена примерно,а о балансировке речи вовсе не было.
Buy a TIG weld man, its better than ordinary arc welder
yes,
From start to finish u did a great job keep up the great work
Thank you so much!
U welcome
Welding on galvanized metal... Someone tell this brother in his language, it's poison.
You should buy some bearing blocks.
Un lavoro molto ben fatto con un ingegno non comune : avrei rinforzato i duomi superiori degli ammortizzatori anteriori e il telaio e avrei messo meno obliqui i braccetti oscillanti la gomma spancia (nota che quando sei salito sopra tendono ad allargarsi sulla carreggiata ) questo è il mio modesto parere comunque i miei complimenti per un lavoro di studio e passione
Wo maske
Do you have plans to seal up the gearbox? How has it held up so far?
I noticed you can only weld in spots, if you want a good continuous weld- drag your welding stick faster when you use it it won't burn through, when it burns through it means you were in one spot for to long, or just turn down the welder, hope this helps
Thanks for the info!
It also looks like he’s using the wrong rod should be using a 6010 AC rod and it looks like he’s using a 7018 DC rod that would make a big difference
.
your missing fact hes welding galvanized steel on top of that...... in a house lol....... hes pretty much going to die anyhow shortly. frame construction least of his worries.
this is a really cool thing you have built but i have some concerns like the lack of any sort of lubrication on your drive train im afraid you will be doin a lot of repairs pretty quickly
Amazing work
Amazing!
Wonderfull congratulacion
Please don't grind using cutting disc. It can easily shattered.
That metal looks incredibly weak as if it will break first time you hit a good bump .
This thing is awesome. Waaaaay over engineered which is a compliment.
I feel like you could get more speed (while losing the reverse and gears ) and just go straight centrifugal clutch . But then again the gears is what kinda made the whole build more interesting
For offroading you dount need speed. Šo gearbox is must have. At last 2 speed. One for mud driving one for more speedy driving. If it has 4 gears. Then its more fun and more effective. With just centrifūgal clutch you will burn that clutch in seconds when you drive in mudpit
@@varde450 The engine itself has a clutch anyway.
This car machine is beautiful, my friend, but it lacks several things, such as headlights, red night lights, and headlights to see in the darkness of the night. My innovative and genius friend, greetings to you from Iraq 🇮🇶👏👏👏👏👏👏👏💋💐👌🏻👍🏻
والله يااخي الكريم ابن عراق المجد ان في بلداننا العربية امكانات لصنع مثلها وابداعات اخرى.
يعني انت لفتت نظره الى الاضوية الامامية في الليل ..يعني فعلا تحتاج الى مثل هذه الاضافات.
Gooooooooooooood job!!
Thanks !!! beautiful workmanship !!! JESUS CHRIST IS LORD !!!! AMEN !!!!!!!
Bhai bike engine se banao na PUBG wala buggy bike ka wil lga ke Belding kar wil banao plz bhai 🙏🙏🙏
New build idea: what about a buggy with a designated cargo space? 🤔
yes, why not
@@ksthacks ooo even crazier idea..... What about a buggy truck hybrid? 😱
@@ksthacks you can tell me to shut up if you want 🥺
You living in city
@@fighteravengergaming7446 not really I'm just on the outskirts of the outskirts of a little town with only 5,000 people 😂
Genial
Why would you weld your bearing races to the plating? I see in other videos you've used pillow block bearings.
Good
Thanks
Pretty good for peanut butter welding
Кастор? Трейл? Аккерман? Углы работы кардана? Нет - не знаю. Но за видео спасибо
щрусы наверное на
таком угле тоже долго не проживут
Рама ИЗ сварки!
Трубогиб? Не, не слыхал)))
@@babayker88 не. Это уже придирки 😁. В принципе этот способ часто самодельщики используют
Мне интересно, это реально в штатах такая разруха?
@@vitalii1980 да,используют и в этом нет ничего страшного,тут ужаснее то,что буквально на всех узлах огромное биение… токарка? Нет,не слышали. Точность? Та какая точность,приварим все на глаз. Сделать болгаркой посадочное место под подшипник,а потом запрессовать… и так пойдёт😂
У меня от этого всего чуть кровь с глаз не пошла. Тут ни один узел не проживёт долго,даже видео не стану до конца досматривать
Amazing DiY
Thank you! 😊
Ustedes son unjenios acostruir o fabricar
con chalas? y las baldozas totalmente llena de quemaduras !!! NO INTENTE ESTO EN CASA
Cross between a go-cart and a dune buggy. How do you keep the dirt out of transmission?
If harbor freight ever built a gocart
Olá. Gostará de saber como foi feito o diferencial
Good ideas and good knowledge, but you work with hooves instead of hands;😅
When cutting, write lengths on the iron, it is not read from the meter, how can we know the length.
Cara vc é muito top, parabéns.
ข
ข
ขอบใจ
Nice👍
Thanks for the visit
có quả hàn tig nữa thì hết bài 😋
Needs seat belt roll cage twice more diameter tires and wheels lower gear ratio. Right now looks really unsafe.
Put on some Good Knobby Tires...