How to connect Encoder with S7-1200 ? || High Speed Counter HSC || TIA PORTAL || Lesson#13

[@ymmijjohnsson]

keep up the good work. There are many channels with the Siemens tia portal, but not many that are as informative as yours

[@medosust]

Very helpful especially wiring

[@gilbertopadovani]

Thanks for the explanation.
Could you tell me where to buy the Seiki CB2000-HC encoder? I tried searching but without success. Thanks in advance.

[@hymdt]

you saved our day with this information ... thanks

[@rashidchibvuri2036]

Great explanation sir thank you.

[@allagomar6033]

Thank you so much bro i wish to continu like this video

[@pajur]

Why is Z signal connected to I0.2? Does it have any sense here? According to S7-1200 manual, only A/B signals are needed.

[@electromecanica_automatismos]

By the way...in this wiring diagram I suppose that your Rotary Encode is NPN output (If not --- PNP--- M (0V) must be connected to 1M.... that`s right?)

[@nirutg5130]

Thank you very much

[@rincebaby145]

Nice video.but how we get reset input the encoder

[@shameehaajmal1517]

Great video! Can I know why all three encoder signal wires are connected to the PLC?

[@EASYPLCTRAINING]

Good question! three wires to detect if the encoder is moving in CW or CCW direction

[@thomassaook7787]

simple & accurate

[@botas82]

Great vídeo, thanks a lot.

[@tourdhorizon97]

2000 pulses per Revolution, how is it possible for this small encoder ????

[@tarekmohsen7572]

Thank you

[@mahmudrajon9104]

very good work.

[@sarpturker5034]

Good tutorial. But one think i cant figure out. Where is the Orange cable Z-phase I0.2? Cant see it in Hardware Inputs?

[@EASYPLCTRAINING]

Yes its i0.2

[@rokibhasan2823]

Can i change the input in monitor mode without using encoder??

[@ahmedrezk2281]

The jumpre on L+and1m error

[@kingofthering1224]

why the counter value reach out to 1700.....??? it must be 1500 only ??? I'm right

[@muhammaddanishhameed9865]

Bhai, encoder se motor ka rpm kis tarah calculate ka sakta hein siemens mein

[@EASYPLCTRAINING]

Calculate no. Of pulses in 2 seconds and multiply with 30 to get rpm

[@muhammaddanishhameed9865]

Thankyou

[@balajisekar2071]

How to connect two or more encoder in one plc

[@EASYPLCTRAINING]

You can install encoder input cards with the plc

[@MaterieUltimeUnofficialChannel]

why +24V is connected to 0V?

[@mohamedayman790]

F

[@yadavsaroj1657]

Sir please same program in omron plc cx-program

[@vorapobautomation9760]

How about S7-1500 HSC ?

[@decentmkiza8570]

Can you do a video of a stepper motor connection and programming

[@EASYPLCTRAINING]

I will try to setup ....

[@decentmkiza8570]

Thanks i am working on s7 1200 1212c ac/dc/rly that would be very helpful

[@karoliczanwojtylanu]

@@EASYPLCTRAINING Yes, it would be great!

[@desifiedCanada]

How to reset count value ?

[@EASYPLCTRAINING]

Move zero in the data register

[@desifiedCanada]

@@EASYPLCTRAINING is there any option for external reset ?

[@EASYPLCTRAINING]

Connect a push button with the PLC, use thus push button signal to move the zero to the encoder data register

[@desifiedCanada]

@@EASYPLCTRAINING should we move zero in IW1000 or QW1000?

[@ghouseahmed4u]

@@EASYPLCTRAINING can we do like this - "Since pulses are DInt format, after counter finishes counting until 2147483647, then can i move "1" to ID1000 directly, so that the cycle repeats?

[@peppealfano65]

non si vede bene

[@nazmikaddora1457]

Thank you so much