You should try mixing mos2 additive in your apache after engine oil flush & in your d400 with old engine oil want to see how difference. 👍🏻 Love you 💘.
I used mos2 on my ct110. The results where Soo good. Engine becomes butter smooth. Engine became so relaxed and got better low end tourque. I have done only 55 km till now so don't know about the fuel efficiency is improved or not. I highly recommend this for smaller capacity engines also but don't use it above recommend amount.
@@janaharajanrajan4652 no need to reduce the amount of engine oil. Make sure to use mos2 shooter pack. If more mos2 added than recommended you may face problems in gear shifting and slipping of gears. Only use the recommended amount if buying in larger quantity. Hope it helps👍
@@janaharajanrajan4652 yes add additive after you drain your old oil. Then add new oil for better dispersion. After adding keep the engine running on idle for 2 to 3 minutes without accelerating.
Bought the MoS2 Anti-Friction Engine Treatment 3/30/2021, poured it in the crankcase then drove off. After 2.5 miles of driving, engine started misfiring, lost a lot of power and barely got us home. Checked the codes when I got home and P0300 and P0305 showed. Shut the engine off, checked for loose connections but didn't find any so I started the car again. After a few minutes of idling, engine struggled then died. Now it is seized and would not start again. Engine had adequate oil and wasn't overfilled when added the Liqui-Moly, coolant level was adequate, no overheating and no issues. Now it's just dead. Car is a 2007 Mercedes ML350 with 165k miles and oil change was only ~1,000 miles ago.
The additive removed the remaining sludge inside the engine, old engines do have some sludge and other stuff clogged up inside, be careful and know their condition before pouring anything in them.
And ceratec is the better additive, btw if you got it repaired again please use amsoil signature series engine oil and don't use this stuff as it isn't needed.
And mos2 is a solid additive, in the case of cars, first it has to be mixed with engine oil before pouring inside, to much solid additive in the upper part of engine was the reason it got seized.
Been using this on my duke and 200ns and the results are satisfactory. Engine smoothness on both the bikes was noticed after approximately 50km of riding after adding the mos2. Did not notice a change in the FE though, but the overall vibrations from the engine on certain RPMs were definitely lowered. 👍
I use it on Duke 250 BS6 2020 model, which works very well. No sound at all during gear shifting, otherwise it was hard and I could hear the sound too. The engine is smooth compared to before. Also, the grunt sound comes very clearly after adding it.
What I timing I AM NO1. Lolz. Addicted to your videos as they are so informative. M also trying to understand my Apache RTR 160 4V . I would love to meet you some day and transfer some of the knowledge.
Can I use it along with fully synthetic engine oil? Or does it work better with mineral/semi synthetic only? My Karizma ZMR has 1.3 liters capacity, will 1 tube of 20ml suffice?
i m using mos2 on my thunderbird 350 , observing really good results . I say it is kinda must do thing on RoyalEnfields we can notice less vibrations and gear shift will get better for sure
Hi Srikanth , can you tell me when to add this mos2 , is it like after using the shooter , flush out the old oil , then add new oil . Post adding the new oil , you should add Mos2 rite ?
@@arunraj2583 yes right. Before adding the flush shooter, make sure the engine is warm, then add shooter and run idle for 10 mins. Then flush out and add new oil. Run for 100kms and add mos2.
@@thesportztourer Since you mentioned to not use over quantity of additive as it can cause slippage, so is this 20ml MoS2 a too more for a 800ml engine oil gearless scooter, since its mentioned for a 1litre engine oil capacity user?
Hi, Will make one for the RTR 200 4V. Your 2nd point is interesting but a very difficult one to execute plus I feel the heat management on the RTR 200 is really good. Any specific reason you want to install a liquid cooling system?
😎 Brother i have mixed mos2 in my old motul 7100 oil that is 1500kms old but the difference found after mixing mos2 is significant dont know why. And after mixing the mos2 in city traffic my radiator fan stating Quickly dont know Liqui moly mos2 additive will give benefit for a old engine oil or not. My bike is pulsar rs 200
@@saurabhgupta9385 you do know if that a video is sponsored, any youtuber has to give a disclaimer as "this video is sponsored by XYZ company" it is illegal if you dont give the disclaimer both in text on the screen and in the audio
Thanks for the great video I have a classic 350 9 years old driven 40k which takes around 2.5 liters oil so 50 ml mos2 which will cost me 1000 is this it worth the price I can do another oil change for the same price what will you recommend ? Please advise
hi, i want to know that if i use AMSOIL 5w30 for my diesel car, is there any benefit to add Liqy moly MOS2 in it, or pouring mos2 in amsoil will damage / worsen engine oil quality or no benifit .
It will work dude Even i use amsoil metric oil 10w40 + liquimoly mos2 in my 200cc motor, Benifits are vibration are decrease in certain rpm. Amsoil already on top in the synthetic with the mos2 mix together it became buttery smooth 👌🏻✨
I installed Purolator oil filter in my swift dzire Diesel ⛽ with MOBIL 3000 5W30 synthetic oil can I add mos2 in engine oil ? I mean I am afraid that it will clog that oil filter or should I switch to maruti oil filter ?
Is that better to use Mos2 on the same time we change the oil ? And would you prefer going with Liquid moly oil with liqui moly additive ? Or is that ok to use any other synthetic oil ?
Hi Sriram, Yes, you can go for it at the time of oil change. As said in the video this can be used with other brand oils as well like I did with shell advance ultra on the FZ25 😊
What is the main difference of Liqui moly Mos 2 which is only made for bike and The Liqui moly oil additive Mos 2 which is made for bike and car both? please explain me sir
it will stay at the bottom of your engine if you park your vehicle very long time (more than 2 weeks). i put in the bottle and mix well. after 2 weeks, check again. the additive stay at the bottom. shake the bottle around 15 minutes before the additive mix again with the oil (but still have a little bit left at the bottom). not sure if this additive will mix well after you park your vehicle very long time. just worry if this additive will clog your oil pump. if you use your vehicle everyday, i think it's not a problem.
Hello dear.. i wanna know which engine oil will be better for my honda hornet, Should i opt for Liquimoly street 10w40 I am currently using Motul 7100 10w40.. Which will be better?
Hi Harsh, I know a few Hornet riders who are happy with the performance of 7100 10W-40. If you have heavy use then street race will be a good choice. Have you checked this video: ua-cam.com/video/2Xz-cav_kUQ/v-deo.html
The Sportztourer it’s great my engines have run smooth I’ve used it in my Wrx for 4 years and now I’m using it in my evo 8 it’s great for performance cars
Sir i have bs6 himalayan and after my 1st servicing i am thing of using it is this one good or should i switch to other brand! You opinion will be helpful thank you❤️
Brother agar aap apke dominar pe abhi jo engine oil laga hua hai uske sathe mos2 abhi daal de to kya waisa benifits milega zaisa new engine oil k sath dalne mai milta hai?
Is it safe for me to use on a new vehicle "RE Interceptor 650", will it make any difference on new condition bike Bike condition as below 1. Purchased around 2 months ago 2. 1st service and oil change done 3. Covered around ~2300kms (Running in period was followed as per RPM limit mentioned in owners manual)
Nothing specific mentioned about it but going by the studies and properties for wet clutch transmission we can use it for every alternate oil drain interval.
Can I use it in Nexon Petrol which comes with 3 cylinder engine with turbocharger? Current odo is 21k service done at 20k with oil change. Kindly reply sir.
For my old dominar 2017 model which has a capacity of 1500ml, i poured some 40ml of mos2.will it cause any issue. As recommended quantity is 2% of the fill capacity. Upon further research i learnt that 1800ml oil has to be poured when completely drained and subsequent refill will be 1500.
U take lot of efforts to make good videos.... zi have one question...Is this a one time product or can it can be added again aftet few thousand kilometers?? What abt clutch slip?
Hello dear, I have a question. Can we use it for pulsar 150 as it has a wet clutch coz some where i heard that using oil treatment in 2 whlrs lear to slipping of clutch. What can we use for fuel treatment in pulsar 150.
Hi Shekhar, You are right about use of friction modifier additives which can effect wet clutch system. In this case 20ml of MoS2 provides the right balance and as mentioned in this video no clutch slip was experienced.
Im using it on my dominar 400 UG with liquimoly 10w60.. Great so far. Do you recommend using this per oil change ? Also does the engine become harsh after 3000 kms ?
Previously 2years ago i used liquimoly 10w60 street race with mos2 in my bs3 pulsar RS200, initial impression was great in low, mid, and top end but after 3000 kilometers, yes exactly after 3000 kilometers i noticed vibration was rapidly increasing day by day in low rpm's thats why i change liquimoly and shifter to motul 300v / amsoil After that i never back to liquimoly engine oil yes i use their mos2 product in regular service intervals.
@@audiophilipp yes better cold start smooth gear shift and vibration less rpm Quantity 25ml in 1litter engine oil If you use more than 25ml mos2 in 1litter engine oil than cause of this clutch slipping
Are you still using this engine oil additive or did you found any better additive then mos2? Did mos2 gave you any negative effect in long run till now?
this liqui moly MOS2 still the best additive for smooth gear shifting on my motorcycle. I just use it when I facing hard gear changes because i try so many engine oil. not just 1 brand. try it 10ml first then if the gear shifting still not smooth, I add another 10ml. usually 20ml just enough to make my gear changes very smooth.
@@thesportztourer not much different in fuel efficiency. with or without LM MOS2 don't have much different. furthermore, I ride most of the time in redline or high rpm at least. 100km/h to 130 km/h on highway. my bike is 185cc from SYM brand. The motorcycle performance is very good because gear shifting very smooth.
Can i use that mos2 can for like 2 years? Or it will get expire because i have opened the seal? I dont ride much thats why i change oil after 6 months.
My Question is mos2 additive from liqui moly can only be usefull when i use liqui moly engine oil? Or i can use mos2 additive in any engine oil like Motul 5100 Semisynthetic Ester oil.
I've noticed everyone saying molybdenum in the oil is making wet clutch slipping , what's the limit in ppm in the oil without clutch slipping , can I use motul 300v 10w40 in an old Kawasaki zx9r 2002 do you think
you used high end expensive engine oil, why u need additional additive? which is u are not sure will make it your motorcycle perform better or worse. if I use motul 300v, I just enjoy the engine oil performance . didn't add any additional additive. i just use this additive on cheaper engine oil if I facing not smooth gear changing.
Since you mentioned to not use over quantity of additive as it can cause slippage, so is this 20ml MoS2 a too more for a 800ml engine oil gearless scooter, since its mentioned for a 1litre engine oil capacity user?
Hi Adarsh, Since scooters run on dry type CVT system, the slippage case is not applicable for them. You can go ahead with 20ml of MoS2 for 800ml oil. Also note if you are using a scooter specific JASO MB engine oil then it will already have additional friction reducing additives.
would it be a good idea to add this after a valve clearance and servicing.? or later after a few oil changes when using cheaper engine oil? i was thinking it would be a good idea for the ms02 to coat everything while " cleaner". or is it " flushed out" at every oil change?
Pls tell me , many UA-camr's claim to PLAN adding additive 400 km prior to engine flush , is there any kind of recommendation from motorbike companies or is it just a better option for users?
Hi Bro.. I am fan of your voice and bike tips.. I have splendor ismart 100cc bike. Could you please suggest me good engine oil. Hero suggesting 10w30 grade oil, is this grade is good for engine if I go long drive around 175 km?
I use Aprilia sr 150....my scooter's recommended oil is Castrol 20 w 40.....I ride around 300+kms...and change engine oil a few days back....now can I use this??? The engine oil limited upto 700 ml....then how much this additive is needed?
Can i use it on my RR310 My bike has done 11km My bike has done 800 km after oil change Should i use it now? My engine oil capacity is 1.7ltr so should i use 1 tube?
Yes, you can use with other engine oils. This one was used with shell advance ultra. Here is the oil change video: ua-cam.com/video/FTRuQR9APXQ/v-deo.html
I m using it in my gixxer 155..20ml.. Now the acceleration punch is gone.. Bike feels sluggish. Now plz help me whether its a clutch slippage issue due to it or my clutch plates are gone.. i added 20ml in 1 liter.. plz help.. love from jammu❤ oil used Castrol power 1 ultimate 10w40 recommend grade.
I have added Liqui Moly MOS2 to my RTR200 7 days back. The engine oil is Shell Advance Ultra 4T 10W40 fully synthetic. I had ridden around 500Km after changing to Shell. Better engine oil than TVS Tru4. After riding 500Km, added MOS2 & so far have ridden almost 200Km. The results are not instant and I started feeling difference after around 100Kms. Now as the Kms are increasing, I call feel the engine getting more smoother. I don't care about increased mileage (which surely will happen due to reduced friction). However, as per various online sources, complete MOS2 effect will be evident after around 500Kms of riding. My RTR200 has completed 25,700 Kms. I did drain entire 1400ml of engine oil before putting Shell oil in it & now I am never going back to TVS Tru4. Next time will try Liqui Moly Street Race. As for the MOS2, I'm loving it. However, in line with recommendations of Liqui Moly, I did not add 28ml of MOS2 as I was concerned of clutch slip. Added 22-24ml only. Still can feel good effects. UA-cam has non-sponsored videos where Molybdenum Disulfide is being used on race engines and despite the high stress on the engines, the wear is extremely low when checked on disassembled engines. So far I'm loving it. There is so much we can do for our beautiful machines. Thanks for your video! Next: Adding MOS2 to my 2003 Fiero F2!
Hey can we use such additives in scooter ? I have a fascino and i was thinking ok using premium engine oil so ... I was considering this as well ! Is it a good idea ?
I use it in my Bonneville, I have seen improvement in shifts of the gearbox, it's an excellent friction modifier
Hi bro do we have to reduce the engine oil for the volume of engine oil additive added
@@janaharajanrajan4652no
correct same like me, but i used it with my kawasaki w650 and mixed with motul 7100
You should try mixing mos2 additive in your apache after engine oil flush & in your d400 with old engine oil want to see how difference. 👍🏻 Love you 💘.
I used mos2 on my ct110. The results where Soo good. Engine becomes butter smooth. Engine became so relaxed and got better low end tourque. I have done only 55 km till now so don't know about the fuel efficiency is improved or not. I highly recommend this for smaller capacity engines also but don't use it above recommend amount.
Hi bro do we have to reduce the engine oil for the volume of engine oil additive added
@@janaharajanrajan4652 no need to reduce the amount of engine oil. Make sure to use mos2 shooter pack. If more mos2 added than recommended you may face problems in gear shifting and slipping of gears. Only use the recommended amount if buying in larger quantity. Hope it helps👍
@@jolin950 thank you bro, for all brand engine oil additive same procedure?
@@janaharajanrajan4652 yes add additive after you drain your old oil. Then add new oil for better dispersion. After adding keep the engine running on idle for 2 to 3 minutes without accelerating.
@@jolin950 thank you bro
It works broo. .
6000-6500 kms service call.(Activa 3g )
.
Liquimoly Fully synthetic oil + Mos2 Shooter + Petrol additive = Smooth n peppy ride ✨
Bought the MoS2 Anti-Friction Engine Treatment 3/30/2021, poured it in the crankcase then drove off. After 2.5 miles of driving, engine started misfiring, lost a lot of power and barely got us home. Checked the codes when I got home and P0300 and P0305 showed. Shut the engine off, checked for loose connections but didn't find any so I started the car again. After a few minutes of idling, engine struggled then died. Now it is seized and would not start again. Engine had adequate oil and wasn't overfilled when added the Liqui-Moly, coolant level was adequate, no overheating and no issues. Now it's just dead. Car is a 2007 Mercedes ML350 with 165k miles and oil change was only ~1,000 miles ago.
The additive removed the remaining sludge inside the engine, old engines do have some sludge and other stuff clogged up inside, be careful and know their condition before pouring anything in them.
And ceratec is the better additive, btw if you got it repaired again please use amsoil signature series engine oil and don't use this stuff as it isn't needed.
And mos2 is a solid additive, in the case of cars, first it has to be mixed with engine oil before pouring inside, to much solid additive in the upper part of engine was the reason it got seized.
Been using this on my duke and 200ns and the results are satisfactory. Engine smoothness on both the bikes was noticed after approximately 50km of riding after adding the mos2. Did not notice a change in the FE though, but the overall vibrations from the engine on certain RPMs were definitely lowered. 👍
Hi bro do we have to reduce the engine oil for the volume of engine oil additive added
@@janaharajanrajan4652 Hi bro. Not at all, it's just 20ml (for duke 200 that is 1.2L of engine oil)
bro I just read a comment that says his engine got seized after he added it and now im scared. Should I go ahead with it or not
I use it on Duke 250 BS6 2020 model, which works very well. No sound at all during gear shifting, otherwise it was hard and I could hear the sound too.
The engine is smooth compared to before. Also, the grunt sound comes very clearly after adding it.
The most underrated channel
Cannot disagree to your comment, all I can say is thanks a lot for your love and support 😊
@@thesportztourer
U deserve 1lakh subscribers for your knowledge and passion for UA-cam
Yeah Ur right bro
You are right
What I timing I AM NO1. Lolz. Addicted to your videos as they are so informative.
M also trying to understand my Apache RTR 160 4V .
I would love to meet you some day and transfer some of the knowledge.
Most underrated good channel in asia :3 love from bangladesh ❤️
I had used it on my Honda Unicorn 160...the 10 ml tube....i think it damaged an expensive bell shaped rubber component in the carburettor...
And once again I'll like to take an opportunity to Thank you for making such great videos on such important topics.
Can I use it along with fully synthetic engine oil? Or does it work better with mineral/semi synthetic only? My Karizma ZMR has 1.3 liters capacity, will 1 tube of 20ml suffice?
i m using mos2 on my thunderbird 350 , observing really good results .
I say it is kinda must do thing on RoyalEnfields
we can notice less vibrations
and gear shift will get better for sure
Thanks a lot Srikanth for sharing your experience here. Happy to read we shared similar experience with gear shifts 😊
Hi Srikanth , can you tell me when to add this mos2 , is it like after using the shooter , flush out the old oil , then add new oil . Post adding the new oil , you should add Mos2 rite ?
@@arunraj2583 yes right. Before adding the flush shooter, make sure the engine is warm, then add shooter and run idle for 10 mins. Then flush out and add new oil. Run for 100kms and add mos2.
Hi bro do we have to reduce the engine oil for the volume of engine oil additive added
I've been using this in my BMW G310GS and the gear shifts have been super smooth since then! Vibrations have also reduced considerably.
Thanks a lot for sharing your first hand experience here.
Did you notice any improvement in fuel efficiency?
@@thesportztourer Since you mentioned to not use over quantity of additive as it can cause slippage, so is this 20ml MoS2 a too more for a 800ml engine oil gearless scooter, since its mentioned for a 1litre engine oil capacity user?
Knowledge, explanation, clear tone... good enough information.... practical ..👍🙏👏👌🇮🇳
Thank you so much for appreciating the efforts. Happy to have support from enthusiasts like you 😊
An erudite and concise video to explain the concept of MOS2. Well done sir.
Clickbait
1. Make a video on rtr 200 4v r.e.2.0 using the same.
2. Can we install liquid coolant + radiator in 200 4v r.e 2.0 ?
Hi,
Will make one for the RTR 200 4V. Your 2nd point is interesting but a very difficult one to execute plus I feel the heat management on the RTR 200 is really good. Any specific reason you want to install a liquid cooling system?
Yes , do a experiment on dominar and Apache !
A detailed video with clearly explained points 👌👌👌👌👌👌 yes you should try on RTR 200
😎 Brother i have mixed mos2 in my old motul 7100 oil that is 1500kms old but the difference found after mixing mos2 is significant dont know why.
And after mixing the mos2 in city traffic my radiator fan stating Quickly dont know Liqui moly mos2 additive will give benefit for a old engine oil or not.
My bike is pulsar rs 200
Liquimoly is Just Promoting it's Brand By Giving UA-camrs to Make Positive Review Videos Use MOTUL products as They are Best.
@@saurabhgupta9385 you do know if that a video is sponsored, any youtuber has to give a disclaimer as
"this video is sponsored by XYZ company" it is illegal if you dont give the disclaimer both in text on the screen and in the audio
@@saurabhgupta9385 mee to bro.. after use it nothing any changes
Don't know why but my bike is getting heated up very quickly.. and also after getting heated up sound of the engine is getting changed drastically
Thanks for the great video I have a classic 350 9 years old driven 40k which takes around 2.5 liters oil so 50 ml mos2 which will cost me 1000 is this it worth the price I can do another oil change for the same price what will you recommend ? Please advise
hi, i want to know that if i use AMSOIL 5w30 for my diesel car, is there any benefit to add Liqy moly MOS2 in it, or pouring mos2 in amsoil will damage / worsen engine oil quality or no benifit .
It will work dude
Even i use amsoil metric oil 10w40 + liquimoly mos2 in my 200cc motor,
Benifits are vibration are decrease in certain rpm.
Amsoil already on top in the synthetic with the mos2 mix together it became buttery smooth 👌🏻✨
I installed Purolator oil filter in my swift dzire Diesel ⛽ with MOBIL 3000 5W30 synthetic oil can I add mos2 in engine oil ? I mean I am afraid that it will clog that oil filter or should I switch to maruti oil filter ?
Is that better to use Mos2 on the same time we change the oil ? And would you prefer going with Liquid moly oil with liqui moly additive ? Or is that ok to use any other synthetic oil ?
Hi Sriram,
Yes, you can go for it at the time of oil change. As said in the video this can be used with other brand oils as well like I did with shell advance ultra on the FZ25 😊
What is the main difference of Liqui moly Mos 2 which is only made for bike and The Liqui moly oil additive Mos 2 which is made for bike and car both? please explain me sir
I am also looking for same answer
Please do a video on adding MoS2 to Apache 200 and share your thoughts. Thanks a lot for all the no BS info you provide. Keep Growing.
it will stay at the bottom of your engine if you park your vehicle very long time (more than 2 weeks). i put in the bottle and mix well. after 2 weeks, check again. the additive stay at the bottom. shake the bottle around 15 minutes before the additive mix again with the oil (but still have a little bit left at the bottom). not sure if this additive will mix well after you park your vehicle very long time. just worry if this additive will clog your oil pump. if you use your vehicle everyday, i think it's not a problem.
What's the difference between this and the shooter (paste) variant ?
Do we have to add mos2 every time we change the oil?
Nooo man .. Never !! Do it 1 time after changing oil 4 times (40 000 km)
Hello dear.. i wanna know which engine oil will be better for my honda hornet, Should i opt for Liquimoly street 10w40 I am currently using Motul 7100 10w40.. Which will be better?
Hi Harsh,
I know a few Hornet riders who are happy with the performance of 7100 10W-40. If you have heavy use then street race will be a good choice. Have you checked this video: ua-cam.com/video/2Xz-cav_kUQ/v-deo.html
It’s by far the best addictive I’ve used it for years
Great! How was your experience?
The Sportztourer it’s great my engines have run smooth I’ve used it in my Wrx for 4 years and now I’m using it in my evo 8 it’s great for performance cars
Sir i have bs6 himalayan and after my 1st servicing i am thing of using it is this one good or should i switch to other brand! You opinion will be helpful thank you❤️
Hi!
At what km are you planning to use this?
Brother agar aap apke dominar pe abhi jo engine oil laga hua hai uske sathe mos2 abhi daal de to kya waisa benifits milega zaisa new engine oil k sath dalne mai milta hai?
Aapko Dominar pe use kar k update karta hoon. Meine expectations toh same hi rakha hai 😊
Is it safe for me to use on a new vehicle "RE Interceptor 650", will it make any difference on new condition bike
Bike condition as below
1. Purchased around 2 months ago
2. 1st service and oil change done
3. Covered around ~2300kms (Running in period was followed as per RPM limit mentioned in owners manual)
Do we need to use it during every oil change? What is a suitable usage frequency for this additive?
Nothing specific mentioned about it but going by the studies and properties for wet clutch transmission we can use it for every alternate oil drain interval.
@@thesportztourer Makes sense. Thanks a lot buddy. Looking forward to your next video.
Can I use it in Nexon Petrol which comes with 3 cylinder engine with turbocharger? Current odo is 21k service done at 20k with oil change. Kindly reply sir.
For my old dominar 2017 model which has a capacity of 1500ml, i poured some 40ml of mos2.will it cause any issue. As recommended quantity is 2% of the fill capacity. Upon further research i learnt that 1800ml oil has to be poured when completely drained and subsequent refill will be 1500.
Can we use it every oil change..? Is it healthy for motorcycles?
U take lot of efforts to make good videos.... zi have one question...Is this a one time product or can it can be added again aftet few thousand kilometers?? What abt clutch slip?
Hello dear,
I have a question.
Can we use it for pulsar 150 as it has a wet clutch coz some where i heard that using oil treatment in 2 whlrs lear to slipping of clutch.
What can we use for fuel treatment in pulsar 150.
Hi Shekhar,
You are right about use of friction modifier additives which can effect wet clutch system. In this case 20ml of MoS2 provides the right balance and as mentioned in this video no clutch slip was experienced.
Im using it on my dominar 400 UG with liquimoly 10w60.. Great so far.
Do you recommend using this per oil change ?
Also does the engine become harsh after 3000 kms ?
Yup use it after each oil change.
Previously 2years ago i used liquimoly 10w60 street race with mos2 in my bs3 pulsar RS200, initial impression was great in low, mid, and top end but after 3000 kilometers, yes exactly after 3000 kilometers i noticed vibration was rapidly increasing day by day in low rpm's thats why i change liquimoly and shifter to motul 300v / amsoil
After that i never back to liquimoly engine oil yes i use their mos2 product in regular service intervals.
@@RSourav_Dey_SINCE_1998 u use thid aditive in motul oil now and its good ?
@@audiophilipp yes better cold start smooth gear shift and vibration less rpm
Quantity 25ml in 1litter engine oil
If you use more than 25ml mos2 in 1litter engine oil than cause of this clutch slipping
Can we use it in 2stroke engines...if yes than please explain it how to use..
Are you still using this engine oil additive or did you found any better additive then mos2? Did mos2 gave you any negative effect in long run till now?
Hi
I have Thunderbird 350. I have purchased Liqui molly 1581 bike additive. How to use it and with how much quantity?
Love u r video straight to the point u earned my subscription
Is it necessary to add it after a fresh oil change or we can add it anytime?
this liqui moly MOS2 still the best additive for smooth gear shifting on my motorcycle. I just use it when I facing hard gear changes because i try so many engine oil. not just 1 brand. try it 10ml first then if the gear shifting still not smooth, I add another 10ml. usually 20ml just enough to make my gear changes very smooth.
Great 👍
Thank you so much for sharing your experience here.
Which motorcycle? Did you notice any change in fuel efficiency?
@@thesportztourer not much different in fuel efficiency. with or without LM MOS2 don't have much different. furthermore, I ride most of the time in redline or high rpm at least. 100km/h to 130 km/h on highway. my bike is 185cc from SYM brand. The motorcycle performance is very good because gear shifting very smooth.
yes would love to see if mos2 makes any difference in d400
Sure 😊
Can i use that mos2 can for like 2 years? Or it will get expire because i have opened the seal? I dont ride much thats why i change oil after 6 months.
My Question is mos2 additive from liqui moly can only be usefull when i use liqui moly engine oil?
Or i can use mos2 additive in any engine oil like Motul 5100 Semisynthetic Ester oil.
0:10 listen...
You can use it on any oil
Need to know more about engine flush of Apache RTR 200.....means which brand is good for flush and engine oil additive
Hi,
Have you checked these videos:
ua-cam.com/video/MZnnHCDq8uU/v-deo.html
ua-cam.com/video/FTRuQR9APXQ/v-deo.html
Have you all noticed what is percentage of Mos2. 90% is paraffin and 0.5% is Mos2. I think the additives couldn't show much differences.
Any change in power delivery bro?
I've noticed everyone saying molybdenum in the oil is making wet clutch slipping , what's the limit in ppm in the oil without clutch slipping , can I use motul 300v 10w40 in an old Kawasaki zx9r 2002 do you think
According to Liquimoly, mos2 should be used maximum 2% volume of engine oil of motorbike
@@awaisiqbal8934 so motul 300v won't make my wet clutch slip as the molybdenum level isn't very high I should be ok , it's a Kawasaki zx9r
@@bccapone837 Agreed 💯
you used high end expensive engine oil, why u need additional additive? which is u are not sure will make it your motorcycle perform better or worse. if I use motul 300v, I just enjoy the engine oil performance . didn't add any additional additive. i just use this additive on cheaper engine oil if I facing not smooth gear changing.
Since you mentioned to not use over quantity of additive as it can cause slippage, so is this 20ml MoS2 a too more for a 800ml engine oil gearless scooter, since its mentioned for a 1litre engine oil capacity user?
Hi Adarsh,
Since scooters run on dry type CVT system, the slippage case is not applicable for them. You can go ahead with 20ml of MoS2 for 800ml oil.
Also note if you are using a scooter specific JASO MB engine oil then it will already have additional friction reducing additives.
Wheter it is useful for tvs jupiter, honda activa etc ?????
would it be a good idea to add this after a valve clearance and servicing.? or later after a few oil changes when using cheaper engine oil? i was thinking it would be a good idea for the ms02 to coat everything while " cleaner". or is it " flushed out" at every oil change?
Hey sportztourer nice video
Just want to know is it good for karizma 2004 model plz let me know
Hi Sahil,
Yes, you can go for it (recommended quantity). 2004 Karizma is a keeper 😊
Pls tell me , many UA-camr's claim to PLAN adding additive 400 km prior to engine flush , is there any kind of recommendation from motorbike companies or is it just a better option for users?
Hi,
Will I see results if I add 20ml mos2 to 1.5 litres of engine oil?
Can you add Mos2 for subsequent oil change after that ? Do you need to do engine oil flush each time after this ?
Just add it when u change your engine oil, usually i flush my engine every year tbh.
Will is alter the engine oil viscosity? it's thicker than our engine oil right?how will it affect engine oil flow inside engine?
Hi Bro.. I am fan of your voice and bike tips.. I have splendor ismart 100cc bike. Could you please suggest me good engine oil. Hero suggesting 10w30 grade oil, is this grade is good for engine if I go long drive around 175 km?
Hi,
Which oil are you using now?
Thanks a lot for the compliments 😊
I use Aprilia sr 150....my scooter's recommended oil is Castrol 20 w 40.....I ride around 300+kms...and change engine oil a few days back....now can I use this???
The engine oil limited upto 700 ml....then how much this additive is needed?
Hi!
I know scooter users who have used 20ml in their scooters and they have shared positive results.
Pl use mos2 on dominar 😊😊👍
Does it not changes the viscosity?? Like 10w40 to 20w40 it can change the figures by 5 to 10 points ?
Bro m using himalayan clicked 6k used mos2 for first time is there any harm regular use of mos2 shooter as technicians advised not use this products
As it is solid lubricant so will it create any sludge deposit in the engine?
Hi do you have the same review for 3M engine oil additive, can you do one review on it please, do you suggest it using in R15 V3, Please reply bro
kindly try this on the dominar as well buddy.... your videos are great 👍🏻.. keep going
Hy can we use moS2 paste which we get with performance pack of liqui moly rather thn using ths
Yes, you can use it. Just make sure you go with the right quality 😊
Hi bro im Gowtham mos2 will with mixed any type of engine oil ????
Your videos are awesome, with the right amount of details. Yes please, I would like to see the effect of MoS2 on Apache
Hello sir,
Due to lack of measurement container, I did put mos2 shooter 5ml extra, which means 35ml mos2 in 1.5ltr. Will I face any issue?
I am little worried... Plz help
Mine is dominar 400 2017 model
Extra 5ml mistakenly went down
Shall I drain all oil? Which I poured it today?
Can i use it on my RR310
My bike has done 11km
My bike has done 800 km after oil change
Should i use it now?
My engine oil capacity is 1.7ltr so should i use 1 tube?
Did you use in 310 bro?
If so Which Oil you used along with MOS2
How to know with what engine oils we should use mos2. Like motul 300v already have some mos2, can we still add it?
Bro. Liquimoly engine oil additive can only pour into liquimoly e.o or any other brand e.o also can pour in?
Hi,
It can be used with other oils like I used it here with Shell Advance ultra 😊
Sir it's necessary to flush engine before using mso2??
Hello bro m using shell ultra fully synthetic 10w40 in unicorn 150 , so can I use MOS2 Along with it . Suggest
He already mentioned. Yes
@@indrockz92 thnks
yes I would really like to know your experience with Dominar 400.
Plz do on RTR, also will it be ok to use motul engine oil (engine oil of any other company) and liqui moly mos2
Yes, you can use with other engine oils. This one was used with shell advance ultra. Here is the oil change video: ua-cam.com/video/FTRuQR9APXQ/v-deo.html
Do we have to add 30 ml to a 1.5 litter engine oil ? So the total quantity will be 1530 ml?
Can I use it on my Pulsar 220 bs4 model? I have changed the engine oil(motul fully synthetic) and have rode 1800kms.
Nice video buddy your videos are really very informative we automotive lovers love ur videos man keep bringing this type of usefull videos
Thanks a lot Deepak for appreciating the videos and supporting the channel 😊
We use liquid MOLY IN out hard working 🚕 🚖 🚕 🚖 TAXIS..IT IS GREAT🎉🎉🎉❤❤SMOOTH RUNNING NOW
Can i use this on my tvs Jupiter
What is negative of using this ? Bearings damage ?
Could it be used in Ntorq also?
I m using it in my gixxer 155..20ml.. Now the acceleration punch is gone.. Bike feels sluggish. Now plz help me whether its a clutch slippage issue due to it or my clutch plates are gone.. i added 20ml in 1 liter.. plz help.. love from jammu❤ oil used Castrol power 1 ultimate 10w40 recommend grade.
Can I use it in Honda unicorn 150 which has run 10000km
How far it ll be effective
Is it good for r15 v2...? Someone Says that it may cause engine damage...
Hi Sir, i have a honda CB400. it has a oil capacity of 4.6 liters. How much Mos2 should i put in? thanks sir. great video.
1liter 20 ml you put 4 mos2 s
I have added Liqui Moly MOS2 to my RTR200 7 days back. The engine oil is Shell Advance Ultra 4T 10W40 fully synthetic.
I had ridden around 500Km after changing to Shell. Better engine oil than TVS Tru4. After riding 500Km, added MOS2 & so far have ridden almost 200Km. The results are not instant and I started feeling difference after around 100Kms. Now as the Kms are increasing, I call feel the engine getting more smoother. I don't care about increased mileage (which surely will happen due to reduced friction). However, as per various online sources, complete MOS2 effect will be evident after around 500Kms of riding.
My RTR200 has completed 25,700 Kms. I did drain entire 1400ml of engine oil before putting Shell oil in it & now I am never going back to TVS Tru4. Next time will try Liqui Moly Street Race.
As for the MOS2, I'm loving it. However, in line with recommendations of Liqui Moly, I did not add 28ml of MOS2 as I was concerned of clutch slip. Added 22-24ml only. Still can feel good effects.
UA-cam has non-sponsored videos where Molybdenum Disulfide is being used on race engines and despite the high stress on the engines, the wear is extremely low when checked on disassembled engines.
So far I'm loving it. There is so much we can do for our beautiful machines.
Thanks for your video!
Next: Adding MOS2 to my 2003 Fiero F2!
Thanks a lot for sharing such a comprehensive experience. Yes, even I felt the difference as km started piling up 😊
How much mos2 should be added to r15 v3 slipper clutch?
After oil change how many kms need to run before adding the additive?
Hi bro u can add the additive every oil change hope it help.
Hey can we use such additives in scooter ? I have a fascino and i was thinking ok using premium engine oil so ... I was considering this as well ! Is it a good idea ?
New 125 engine or old engine?
Can it be used at every oil change interval?
Yes
Can this be used for a brand new bike ?
Is there any update on the long term use. I am about to put into my Ninja 650 after 11,000 miles and regular dealer servicing.
vai
kya isko use karne se engine oil patla ho jaata hain? want to use this on gixxer 155 with motul 300v 10w40